This change switches all existing users of ast2500 Watchdog to Driver
Model based Watchdog driver.
To perform system reset Sysreset Driver uses first Watchdog device found
via uclass_first_device call. Since the system is going to be reset
anyway it does not make much difference which watchdog is used.
Instead of using Watchdog to reset itself, SDRAM driver now uses Reset
driver to do that.
These were the only users of the old Watchdog API, so that API is
removed.
This all is done in one change to avoid having to maintain dual API for
watchdog in between.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Reset Driver for ast2500 SoC. This driver uses Watchdog Timer to
perform resets and thus depends on it. The actual Watchdog device used
needs to be configured in Device Tree using "aspeed,wdt" property, which
must be WDT phandle, for example:
rst: reset-controller {
compatible = "aspeed,ast2500-reset";
aspeed,wdt = <&wdt1>;
}
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make functions for locking and unlocking SCU part of SCU API.
Many drivers need to modify settings in SCU and thus need to unlock it
first. This change makes it possible.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver supports ast2500 and ast2400 SoCs.
Only ast2500 supports reset_mask and thus the option of resettting
individual peripherals using WDT.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
am33xx does not support OneNAND, but we need this define anyway
to let UBI SPL code compile.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.
Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
R40 has a similar SATA controller with the ones on A10/A20, but with a
reset line added (like other peripherals on sun6i+), and two extra VDD
pins added (1.2v and 2.5v).
Add clock configuration of R40 SATA.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This converts the following to Kconfig:
CONFIG_CMD_BLOB
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add imply CMD_BLOB under CHAIN_OF_TRUST]
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds support for HDMI output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs.
Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this
naming.
Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim
down the arch/arm/Kconfig level.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The register names and offset were not correct as per the TRM for OMAP3530
and OMAP3630. Correct the naing and offsets per the documentation
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
PSCI can be used on both multiple and single core socs. Current
implementation only allows PSCI to work on multiple core socs.
This patch removes this restriction so that PSCI can work on
single core socs as well.
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is needed for HDMI, which will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Video driver for older Allwinner SoCs uses cfb console framework which
in turn uses struct ctfb_res_modes to hold timing informations. However,
DM video framework uses different structure - struct display_timing.
It makes more sense to convert lcdc to use new timing structure because
all new drivers should use DM video framework and older drivers might be
rewritten to use new framework too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
TCON unit has similar layout and functionality also on newer SoCs. This
commit splits out TCON code for easier reuse later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 has the CPUCFG block at the same address as the A20.
Fix it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.
This patch enables it for all the PLLs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present if the return to bootrom fails (e.g. because you are not using
the Rockchip's bootrom's pointer table in MMC) then the board prints
SPL message and hangs. Print a message first if we can, to help in
understanding what happened when it hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:
[Linux] [U-Boot]
arch/arm/kernel/smccc-call.S -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes* -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h -> include/linux/arm-smccc.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add NAND secure boot target for ls1043ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define bootscript and its header addresses for QSPI target
Also add PPA header address in Kconfig
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The header address of PPA defined in Kconfig.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The RK3399-Q7 ("Puma") SoM exposes UART0 as the Qseven UART (i.e. the
serial line available via standardised pins on the edge connector and
available on a RS232 connector).
To support boards (such as the RK3399-Q7) that require UART0 as a
debug console, we match CONFIG_DEBUG_UART_BASE and add the appropriate
iomux setup to the rk3399 SPL code.
As we are already touching this code, we also move the board-specific
UART setup (i.e. iomux setup) into board_debug_uart_init(). This will
be called from the debug UART init when CONFIG_DEBUG_UART_BOARD_INIT
is set.
As the RK3399 needs to use its board_debug_uart_init() function, we
have Kconfig enable it by default for RK3399 builds.
With everything set up to define CONFIG_BAUDRATE via defconfig and
with to have the SPL debug UART either on UART0 or UART2, the configs
for the RK3399 EVB are then update (the change for the RK3399-Q7 is
left for later to not cause issues on applying the change).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM controller in the Allwinner H5 SoC is again very similar to
the one in the H3 and A64.
Based on the existing socid parameter, add support for this controller
by reusing the bulk of the code and only deviating where needed.
These new bits set or cleared here and there have been mostly found by
looking at DRAM register dumps after using the H5 boot0 and comparing
them to what we set in the code. So for now it's mostly unclear what
those bits actually mean - hence the missing names and comments.
Also add the delay line parameters taken from the boot0 and libdram
disassembly.
Register setup differences between H5 and H3 are courtesy of Jens Kuske.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB,
while the first SRAM region is mapped at address 0.
With the extended physical memory support of the A80 this was changed,
so the BROM is now at address 0 and the SRAM region starts right behind
this at 64KB. This configuration seems to be called "high SRAM".
Instead of enumerating the SoCs which have copied this configuration,
let's call a spade a spade and introduce a Kconfig option for this setup.
SoCs implementing this (A80, A64 and H5, so far), can then select this
configuration.
Simplify the config header definition on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
To add GMAC (Gigabit Ethernet) support (limited to RGMII only at this
point), we need support for additional pin-configuration. This commit
adds the pinctrl support for GMAC in RGMII signalling mode:
* adds a PERIPH_ID_GMAC and the mapping from IRQ number to PERIPH_ID
* adds the required defines (in the GRF support) for configuring the
GPIOC pins for RGMII
* configures the RGMII pins (in GPIOC) when requested via pinctrl
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.
DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.
EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.
Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which makes the whole
startup take a lot of time. We therefore want to at least move to the safe
600MHz value we can use with default pmic settings.
This is also the freqency the proprietary sdram-init leaves the cpu at.
For boards that have pmic control later in u-boot, we also add the option
to set the maximum frequency of 1.6GHz, if they so desire.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The SPL binary needs to be prefixed with the boot magic ('RK33' for
the RK3399) on the Rockchip platform and starts execution of the
instruction word following immediately after this boot magic.
This poses a challenge for AArch64 (ARMv8) binaries, as the .text
section would need to start on the odd address, violating natural
alignment (and potentially triggering a fault for any code that
tries to access 64bit values embedded in the .text section).
A quick and easy fix is to have the .text section include the 'RK33'
magic and pad it with a boot0 hook to insert 4 bytes of padding at the
start of the section (with the intention of having mkimage overwrite
this padding with the appropriate boot magic). This avoids having to
modify the linker scripts or more complex logic in mkimage.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Layerscape Chassis-2 have PCIe device, some platform devices and
DPAA1 devices which will use stream-ids for iommu level isolation
as they are behind SMMU.
This patch defines the stream-ids for Chassis-2 devices. DPAA1 is
reserved for future use.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080a, LS1088a and LS2088a SOCs are based on Chassis-3 and shared
same stream-id partitioning. This patch rewords the definition to
support all these SOCs.
Also have changes in description about iommu-map property updates
in PCI node.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The stream ID allocation for Chasis 3.0 devices can be shared among
LS1088, LS2088 and LS2080.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For validating images from uboot (Such as Kernel Image), either keys
from SoC fuses can be used or keys from a verified table of public
keys can be used. The latter feature is called IE Key Extension
Feature.
For Layerscape Chasis 3 based platforms, IE table is validated by
Bootrom and address of this table is written in scratch registers 13
and 14 via PBI commands.
Following are the steps describing usage of this feature:
1) Verify IE Table in ISBC phase using keys stored in fuses.
2) Install IE table. (To be used across verification of multiple
images stored in a static global structure.)
3) Use keys from IE table, to verify further images.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moved the ifdef into ppa.h and removed the duplicated macros.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add header address for PPA to be validated during ESBC phase for LS2080A
platform based on Layescape Chasis 3.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since the lpc32xx i2c driver does not yet support the devicetree bindings,
this structure is also needed by the board file as the hardware description
is done there.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Non OMAP platforms i.e. Keystone will also need to use the board
EEPROM helpers so let's make the macro platform independent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
GPIO_TO_PIN(bank, bank_gpio) returns the GPIO index
from the GPIO bank number and bank's GPIO offset number.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
We only support cores that do Thumb-1 or later. So we add a comment to
explain this and remove the architecture test.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of initializing 'struct src' to SRC_BASE_ADDR on
every function better to have global define macro.
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Use meaningful macros IMX6_BMODE_*, instead of numerical
number in boot mode detection code.
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
For i.MX6, the bootmode determine code is part of spl_boot_device,
but there is might be a possibility for other part the code need to
check the desired boot mode for adding new functionalities like
modeboot env variable, or changing boot order etc.
So introduced imx6_src_get_boot_mode which actually reading the
boot mode register for desired modes.
More cleanup will be add in future patches.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add CAAM clock functions, SEC_CONFIG[1] fuse checking, and default CSF
size for HAB support boot on mx7ulp.
Users need to uncomment the CONFIG_SECURE_BOOT in mx7ulp_evk.h to build
secure uboot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add the iomux pins header file from iomux tool team. Change the IOMUXC0 pins
to add IOMUX_CONFIG_MPORTS flags.
Note: The IOMUXC0 offset provided in this file is from 0xD000, this is not
aligned with IOMUXC0 base address. We have adjusted the IOMUXC0 base address
to aligin with it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update the mxc_ocotp driver to support i.MX7ULP.
The read/write sequence has some changes due to
PDN and OUT_STATUS registers added and TIME register is
removed. Also update the bank size and number.
Add is_mx7ulp macro in sys_proto.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add the imx_rgpio2p driver for Rapid GPIO2P controllers on i.MX7ULP.
Have added all ports on RGPIO2P_0 and RGPIO2P_1.
The configurations CONFIG_IMX_RGPIO2P and CONFIG_DM_GPIO must be set
to y to enable the drivers.
To use the GPIO function, the IBE and OBE needs to set in IOMUXC.
We did not set the bits in driver, but leave them to IOMUXC settings
of the GPIO pins. User should use IMX_GPIO_NR to generate the GPIO number
for gpio APIs access.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Implement the i2c clock enable and get function for mx7ulp. These
functions are required by imx_lpi2c driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Implement soc level functions to get cpu rev, reset cause, enable cache,
etc. We will disable the wdog and init clocks in s_init at very early u-boot
phase.
Since the we are seeking the way to get chip id for mx7ulp, the get_cpu_rev
is hard coded to a fixed value. This may change in future.
Reuse some code in imx-common.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a clock framework to support SCG1/PCC2/PCC3 for A7 to support get/set
clock source, divider, clock rate and parent source.
Users need to include pcc.h to use the APIs to for peripherals clock. Each
peripheral clock is defined in enum pcc_clk type.
SCG relevants APIs are defined in scg.h which supports clock rate get, PLL/PFD
enablement and settings, and all SCG clock initialization. User need use enum
scg_clk to access each clock source.
In clock.c, we initialize necessary clocks at u-boot s_init and implement the
clock functions used by driver modules to operate clocks dynamically.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while IOMUXC1 is for A7. We set IOMUXC1 as
the default IOMUX in this driver. Any pins in IOMUXC0 needs
to configure with IOMUX_CONFIG_MPORTS in its mux_mode field.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add imx-regs.h for i.MX7ULP registers addresses definitions and some
registers structures.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add rk3328 pinctrl driver and grf/iomux structure definition.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3399 support DDR3, LPDDR3, DDR4 sdram, this patch is porting from
coreboot, support 4GB lpddr3 in this version.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
The sdram controller blocks are very similar to the rk3288 in utilizing
memory scheduler, Designware uPCTL and Designware PUBL blocks, only
limited to one bank instead of two.
There are some minimal differences when setting up the ram, so it gets
a separate driver for the rk3188 but reuses the driver structs, as there
is no need to define the same again.
More optimization can happen when the modelling of the controller parts
in the dts actually follow the hardware layout hopefully at some point
in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add a driver for setting up and modifying the various PLLs and peripheral
clocks on the RK3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
PMU is the power management unit and GRF is the general register file. Both
are heavily used in U-Boot. Add header files with register definitions.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
So far spl-boards have declared the back_to_brom() function as simple
extern in the files themself. That doesn't scale well if every boards
defines this on its own.
Therefore move the declarations to a bootrom header.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Use defines to describe the bit shifts used to create the
table for ddrconf register values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
rk3399 has different syscon registers which may used in spl,
add to support rk3399 spl.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
rk3399 grf register bit defenitions should locate in header
file, so that not only pinctrl can use it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
