Add pinctrl and sdmmc nodes to add MMC support for
STM32H743 evaluation board.
Evaluation board needs a second pinctrl node
"pinctrl_sdmmc1_level_shifter" to drive a level shifter
on MMC bus.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch remove the extra compatibility string "st,stm32h7-usart"
and "st,stm32f7-usart" to avoid confusion, save some time & space.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Banana Pi M1 Plus is an open-source single-board computer
that adds more connectivity to the classic board using
Allwinner A20 SOC.
Bananapi M1-Plus features:
- A20 Dual-core 1.0GHz
- 1 GB DDR3 SDRAM
- MicroSD
- 10/100/1000 Ethernet RJ45
- WiFi b/g/n
- 5V DC Micro USB power-supply
For dts file,
Sync with Linux commit f92ca09("Merge branch 'akpm/master'").
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The upstream (Linux) device tree file for the Bananapi M3 follows the
convention of using the well known brand name, instead of the vendor
name, for naming. The file was recently added to upstream in commit
359b5a1e1c2d ("ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi
BPI-M3")
Rename the device tree file in U-boot to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
From rev.J A20-OLinuXino-MICRO has eMMC option. For now this is
only 4GB, but in the future size may increase.
The dts file is the same from mainline kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The kernel DT of the SinA33 has evolved quite a bit. Make sure we sync it
and its upstream DTSI to be able to use the OTG. The DTs were taken from
the 4.13 kernel release.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The (Qseven) BIOS_DISABLE signal on the RK3399-Q7 (Puma) keeps the
eMMC and SPI in reset initially and we need to write a GPIO to turn
them on before continuing the boot-up.
This adds the DTS entries for the additional regulator and makes
pinctrl and gpio3 available during SPL. It also adds a hook to the
spl_board_init() to ensure that the regulator gets probed and enabled.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the general case, we want to continue booting the full U-Boot
(contained in a discoverable FIT image) from the same device the SPL
stage was loaded from. This prepends the 'same-as-spl' specifier to
our configurable boot-order to make this the default behaviour.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add i2c1 and rk805 nodes to support rk805 init setting.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This re-syncs omap3 DTS file with current file from
Linux v4.14-rc1 to ensure a consistent configuration. Upstream
Linux removed the redundant Interrupt-parent property from usbhsohci,
usbhsehci, ssi_port1 and ssi_port2 sub nodes.
Signed-off-by: Karthik Tummala <karthik@techveda.org>
With DM enabled, gpio numbering is assigned based on the
probed order of gpios, irrespective of the gpio base. So enable
all necessary gpios in SPL.
Fixes: edf25d94d55c (“ARM: dts: OMAP5+: Enable gpio in SPL”)
Reported-by: Gou, Hongmei <h-gou@ti.com>
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.
There are some spacing issues in the patch, but they appear to be
present in the Linux source files. I'll try to get to fixing them there,
and do a future re-sync at a later date.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With DM now enabled with the device tree pulled from Linux, we can
enable DM_I2C in U-Boot.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add DM_I2C_COMPAT to da850_am18xxevm to fix warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A few small additional items are needed to support DM_SPI and
DM_SERIAL, so those were added to da850-evm-u-boot.dtsi
Signed-off-by: Adam Ford <aford173@gmail.com>
The PHY reset GPIOs were missing from the DT, add them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :
_ Add RCC clock driver node and update all clocks phandle
accordingly.
By default, on kernel side, all clocks was temporarly
configured as a phandle to timer_clk waiting for a RCC
clock driver to be available.
On U-boot side, we now have a dedicated RCC clock driver, we
can configured all clocks as phandle to this driver.
All this binding update will be available soon in a kernel tag,
as all the bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
_ Align STM32H7 serial compatible string with the one which will be
available in next kernel tag. The bindings has been acked by
Rob Herring [2].
This compatible string will be usefull to add stm32h7 specific
feature for this serial driver.
[2] https://lkml.org/lkml/2017/7/17/739
_ Add gpio compatible and aliases for stm32h743
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add missing HSI and CSI oscillators nodes needed
by STM32H7 RCC clock driver.
Clock sources could be:
_ HSE (High Speed External)
_ HSI (High Speed Internal)
_ CSI (Low Power Internal)
These clocks can be used as clocksource in some configuration.
By default, HSE is selected as clock source.
_ Set HSE to 25Mhz for stm32h743i-disco and eval board
By default, the external oscillator frequency is defined at
25 Mhz in SoC stm32h743.dtsi file.
It has been set at 125 Mhz in kernel DT temporarly waiting for
RCC clock driver becomes available.
As in U-boot we got a RCC clock driver, the real value of HSE
clock can be used.
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This file is imported from linux kernel v4.13
Add device tree support for STM32H743 evaluation board.
This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS and FS
_ I2 C compatible serial interface
_ RTC with rechargeable backup battery
_ SAI Audio DAC
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM, 1Mx16bit SRAM and 8Mx16bit NOR Flash
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Potentiometer
_ 4 colored user LEDs
_ Reset, wakeup, tamper or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
Power jack
3 USB with Micro-AB
RS-232 communications
Ethernet RJ45
FD-CAN compliant connection
Stereo headset jack including analog microphone input
2 audio jacks for external speakers
microSD™ card
JTAG/SWD and ETM trace
_ Expansion connectors:
Extension connectors and memory connectors for daughterboard
or wire-wrap board
_ Flexible power-supply options: ST-LINK USB VBUS or external
sources
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update ehci and ohci node's compatible string in order to
use ehci-generic and ohci-generic drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On STi 96boards, configure by default the micro USB connector
(managed by DWC3 hardware block) in peripheral mode.
This will allow to use fastboot feature.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
reset-names property is needed to use the reset
API for STi sdhci driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368 TPL stage always returns to the BootROM, so it has no need
for the eMMC, SD and SPI nodes. This marks those nodes (that should
be included in SPL, but not TPL) as 'u-boot,dm-spl'.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7, we need to turn on the on-module USB hub before using the
USB host interfaces (only the OTG interface is directly connected to the edge
connector). This drops the deprecated 'rockchip,vbus-gpio' property and uses
a fixed regulator to turn on the USB hub.
References: 26a8b80 "usb: host: xhci-rockchip: use fixed regulator to control vbus"
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To support bootstage recording, we want to mark our DM timer as the
tick-timer; this triggers the support for 'trying harder' to read the
timer in the Rockchip DM timer driver, even if the device model isn't
ready yet.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds USB OTG/EHCI/OHCI nodes for evb-rv1108 USB ports.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
commit b63b995 (arm: dts: Add u-boot specific compatibles) separated out
u-boot specific compatibles from dts files.
The u-boot specifics were moved in *-u-boot.dtsi files for all dra7
platforms except dra7-evm.
Without it the SD card is broken on DRA7-evm because the regulator cannot
be enabled.
Fix it by adding the missing dra7-evm-u-boot.dtsi with the needed
properties.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2
with 1Gbit DDR2-SDRAM in a single package.
The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and
Mac-address EEPROM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For sama5d2, add the sfr node with syscon support.
In order to access the SFR_UTMICKTRIM register for the utmi clock
driver, add the phandle property for the utmi node to point to the
sfr node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The DTS files had some spacing issues and they needed fixing. This
pull re-sync's the OMAP3xx related DTS files with Linux 4.13-RC5.
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.
Signed-off-by: Adam Ford <aford173@gmail.com>
V3: The resync broke card detect on MMC1 on Logic PD's Torpedo,
so we add the cd-invert to the Torpedo's -u-boot.dtsi file.
V2: Add the u-boot.dtsi files for OMAP3, OMAP36xx, and Torpedo
Remove the need for the second patch in the series
Fix the building warning as below:
---8<----
Warning (reg_format): "reg" property in /i2c-gpio-0/pcf8563@50 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /i2c-gpio-0/pcf8563@50
Warning (avoid_default_addr_size): Relying on default #size-cells value for /i2c-gpio-0/pcf8563@50
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The R8A7796 XHCI USB nodes are missing from r8a7796 dtsi, add them.
These nodes don't come from mainline Linux, yet the DT binding is
similar enough to R8A7795 which already has those in mainline and
once the nodes hit mainline, this DT should be resynched.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7796 EHCI USB nodes are missing from r8a7796 dtsi, add them.
These nodes don't come from mainline Linux, yet the DT binding is
similar enough to R8A7795 which already has those in mainline and
once the nodes hit mainline, this DT should be resynched.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.13,
commit 569dbb88e80deb68974ef6fdd6a13edb9d686261 . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace the code to set the ethernet mac address with the code from
the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Separate out u-boot specific compatibles from dts files.
This will help in syncing dts files in future.
Also these will get deleted eventually once respective drivers
are capable of handling Linux dts files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
U-boots spi-nor support is currently considered a work in progress. For
now to avoid issues it is necessary to add a "spi-flash" compatible
string. Eventually the "jedec,spi-nor" will be sufficient when the core
U-boot code is updated to support it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This re-syncs AM33xx DTS file with current file from
Linux v4.13-rc4 to ensure a consistent configuration. Upstream
Linux removed the redundant Interrupt-parent property from mmc,
mac, lcdc and tscadc sub nodes.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We need the clock available very early, add the u-boot,dm-pre-reloc
DT property on those nodes, so they come up very in the process.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since commit 576e3cc700 ("usb: host: xhci-dwc3: Add dual role mode
support from DT"), warning is displayed if dr_mode is not specified.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are two same gmac node, remove one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update the tx_delay and rx_delay to match the timing for
rk3399-firefly board to improve the stability of gmac data
transfer.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.
OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
mmc using 150000000 as max-frequency like what rk3288 sets.
This can speed up the mmc read/write, the actual mmc clock is:
Before this patch: 37.125M
After this patch: 49.5M
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
add node for sdmmc in dts and rk3229-evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Device drivers like debug serial, dmc should be enabled before
relocation, so add u-boot.dtsi files to contain devices that
should be marked as dm-pre-reloc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To use it with the DM timer driver in SPL and TPL, timer0 needs to be
marked as pre-reloc.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368-uQ7 (codenamed 'Lion') is a micro-Qseven (40mm x 70mm,
MXM-230 edge connector compatible with the Qseven specification)
form-factor system-on-module based on the octo-core Rockchip RK3368.
It is designed, supported and manufactured by Theobroma Systems.
It provides the following features:
- 8x Cortex-A53 (in 2 clusters of 4 cores each)
- (on-module) up to 4GB of DDR3 memory
- (on-module) SPI-NOR flash
- (on-module) eMMC
- Gigabit Ethernet (with an on-module KSZ9031 PHY)
- USB
- HDMI
- MIPI-DSI/single-channel LVDS (muxed on the 'LVDS-A' pin-group)
- various 'slow' interfaces (e.g. UART, SPI, I2C, I2S, ...)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For full SPL support, including DRAM initialisation, we need a few
nodes from the DTS: this commit adds the DMC (DRAM controller) node,
the service_msch (memory scheduler) node and marks GRF, PMUGRF and CRU
as 'u-boot,dm-pre-reloc'. In addition to this, we also include the
dt-binding for the DMC to allow DTS files including this DTSI to refer
to the symbolic constants for the DDR3 bin and for the
memory-schedule.
Note that the DMC contains both the memory regions for the
(Designware) protocol controller as well as the DDR PHY.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We will to drop device security temporarily (until the ATF initialises
it fully) from the TPL/SPL stage: this requires access to some
registers in the SGRF.
This adds the sgrf node to the rk3368.dtsi, so we can then bind a
syscon device onto it and access its memory ranges.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Synced ohci0 and ehci0 nodes from Linux for sun50i-a64.dtsi
Here is the Linux last merge tag details:
Merge: 0e91f43d e5770b7
Author: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Fri Jun 9 14:59:55 2017 +1000
Merge remote-tracking branch 'staging/staging-next'
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The node name for the power seq pin is mmc2@0 like the mmc2_pins_a one.
This makes the original node (mmc2_pins_a) scrapped out of the dtb and
result in a unusable eMMC if U-Boot didn't configured the pins to the
correct functions.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and driver
model. The peripheral clock and pins configuration are handled by
the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.12-rc6,
commit 6f7da290413ba713f0cdd9ff1a2a9bb129ef4f6c . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not using board revision is causing confusion about which board is
supported and tested. Mark dts files exactly with board revision which
was tested. When new board revision arives it can be symlink if SW view
is the same. Also add -revX suffix to compatible string because user space
tools are parsing this string and can change behavior depends of board
revision.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Z-Turn board is a low cost development board based on the
Xilinx Zynq SoC. While it's powerful and quite versatile, it
so far lacked upstream support.
This patch adds basic support for the Z-Turn. It does however
for now miss enablement for MIO51 reset which means that USB
and ethernet don't work. For that either FSBL or SPL need to
be adjusted. The SPL part will follow later.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
