Since commit ce412b79e7 ("drivers: net: phy: atheros: add separate
config for AR8031") Ethernet does not work on mx6sabreauto.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on mx6sabreauto design we need some additional configurations,
such as enabling the 125 MHz AR8031 output and setting the TX clock
delay that need to be done in the board file.
This is the equivalent fix from commit 4b6035da48 ("mx6sabresd: Make
Ethernet functional again").
Reported-by: Miquel RAYNAL <miquel.raynal@free-electrons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for Falcon mode and explain in the README the steps to
boot the kernel directly without loading the full U-Boot.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
WEIM cannot be used when I2C3 is enabled due to pin conflict, so keep
WEIM disabled by default.
I2C3 controls GPIO I2C expander (USB host and OTG have VBUS controlled by
the GPIO I2C expander), magnetometer, accelerometer.
Not disabling WEIM in U-Boot causes I2C3 to behave badly when booting
a NXP 4.1 kernel, which leads to probe failure on several devices,
including the lack of USB:
imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517
By keeping WEIM disabled in U-Boot these kernel issues are gone.
Reported-by: Takashi Matsuzawa <tmatsuzawa@xevo.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.
This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.
Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg
Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg
Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The Cubox-i and Hummingboard series of devices have an option of
SATA on board, and depending on how the fuses are blown even the
option to boot SPL from SATA. So enable support for it so it can
be used to boot the OS from if people desire.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
This change sets the VLDO4 settings output to 2.8V in PMIC
initialization so that the MIPI DSI/CSI input voltage is 2.8V
as per the schematics. The original code provides an output of
3.3V which violates the voltage mentioned in the schematics.
Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
imx6qdl_icore_mmc_defconfig => imx6qdl_icore_rqs_defconfig
Since icorem6_rqs support MMC/eMMC boot, so doesn't need
to name it explicitly.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
There is no need to add a 100us delay after the DDR initialization.
Other imx6 boards do not have such delay either, so simply remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The Turris Omnia is a open-source router created by CZ.NIC.
The code is based on the Marvell/db-88f6820-gp by Stefan Roese
with modifications from Tomas Hlavacek in the CZ.NIC turris-omnia-uboot
repository, which can be found at
https://gitlab.labs.nic.cz/turris/turris-omnia-uboot
By default, the Turris Omnia uses btrfs as the main and only filesystem,
and also loads kernel and device tree from this filesystem. Since U-Boot
does not yet support btrfs, you should not flash your Turris Omnia board
with this unless you know what you are doing.
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 board/CZ.NIC/turris_omnia/Makefile
create mode 100644 board/CZ.NIC/turris_omnia/kwbimage.cfg
create mode 100644 board/CZ.NIC/turris_omnia/turris_omnia.c
create mode 100644 configs/turris_omnia_defconfig
create mode 100644 include/configs/turris_omnia.h
Signed-off-by: Stefan Roese <sr@denx.de>
The DDR3 training code for Marvell A38X currently computes 1t timing
when given board topology map of the Turris Omnia, but Omnia needs 2t.
This patch adds support for enforcing the 2t timing in struct
hws_topology_map, through a new enum hws_timing, which can assume
following values:
HWS_TIM_DEFAULT - default behaviour, compute whether to enable 2t
from the number of CSs
HWS_TIM_1T - enforce 1t
HWS_TIM_2T - enforce 2t
This patch also sets all the board topology maps (db-88f6820-amc,
db-88f6820-gp, controlcenterdc and clearfog) to have timing set to
HWS_TIM_DEFAULT.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is not a very useful name since once it is probed it still hangs
around. With driver model we will use uclass data for this, so rename the
struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The instructions for creating a disk image that are presently in
README.sandbox fail because sfdisk doesn't know about GPT.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Enable all the boot-on regulator in default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Probe dwc2 udc in the function of board_usb_start to enable
usb gadget function.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The bank0 ram size should be the DRAM size minus reserved size,
the DRAM size may be 1GB, 2GB, 4GB, we can not hard code it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Added DECLARE_GLOBAL_DATA_PTR for RK3328, RK3368 and RK3399:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Replace the sdram_init() in board init and rockchip_sdram_size() in
sdram driver for all the Rockchip SoCs which enable CONFIG_RAM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make dram_init() in rk3036-board.c conditional on CONFIG_RAM:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
K2G ICE evm will have its own dtb. Therefore, add it to the list of dtbs
located in the appended U-boot dtb FIT image. Therefore, when swapping out
dtbs K2G ICE boards can grab the correct one.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to allow "board_name" to
be set depending on the board it is being ran on.
Update findfdt to use this new dynamic board_name value to determine
which dtb should be used.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Certain peripherals used by K2G GP aren't used on K2G ICE evm. Or
configuration is slightly different. Therefore, use board detection to
deal with these variations.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some code doesn't apply to K2G ICE evm. Therefore, use board detection to
wrap these calls.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration settings used by the K2G ICE evm. Also use board
detection to determine which DDR3 configuration to use.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add basic pinmux data for new K2G ICE evm. Also add pinmuxing for a
generic K2G evm which includes I2C 0 and 1 used for board detection
purposes.
Since multiple K2G boards are supported that means initially generic
pinmuxing should be used when board detection hasn't ran. Once board
detection runs the proper pinmuxing can be reran to match the board
being ran on.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a function that can be used to determine if the board being ran on is
a K2G Industrial Communication Engine EVM or K2G General Purpose EVM based
on values programmed on the EEPROM.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some K2G evms have their EEPROM programming while most do not. Therefore,
add EEPROM board detection to be used as the default method and fall back
to the alternative board detection when needed.
Also reorder board configuration. Perform bare minimal configuration
initially since board detection hasn't ran. Finish board configuration
once the board has been identified.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now with support for U-boot runtime dtb selection each board needs to
define board_fit_config_name_match so U-boot can determine what the
correct dtb is within the FIT blob.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For K2G, runtime DTB selection utilizes the embedded_dtb_select function.
Therefore, define the function which will perform a EEPROM read and then
retries selecting the correct dtb now that it can detect which board its
on. For other Keystone devices use an empty function since they will still
use the embedded FIT functionality but their FIT will only contain a single
dtb.
Most production K2G boards do not have their EEPROM programmed. Therefore,
perform a test to verify a K2G GP is currently being used and if it is then
set the values normally set by a EEPROM read.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When the EEPROM is first read its contents are stored in memory as a
cache to avoid further I2C operations. To determine if the EEPROM was
previously read the easiest way is to check the memory to see if the
EEPROM's magic header value is set. Create a new function that can
determine if the EEPROM was previously read or not without having to
perform a I2C transaction.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In some situations the EEPROM used for board detection may not be
programmed or simply programmed incorrectly. Therefore, it may be
necessary to "simulate" reading the contents of the EEPROM to set
appropriate variables used in the board detection code.
This may also be helpful in certain boot modes where doing i2c reads
may be costly and the config supports running only a specific board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Franklin S Cooper Jr. <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It's been a while since I've touched U-Boot on the Raspberry Pi and
other things have been taking my time. Drop my maintainership for this
port.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The 82xx board mgcoge3ne was removed from the codebase, so this is dead
code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Discern the SoMs based on the presence of SPI flash to support both
variants of the SoM, one booting from SPI NOR and one booting from
eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Continue loading U-Boot from MMC2 when the SPL was loaded using SAM-BA
loader. This allows the board to boot system from the removable media
instead of the eMMC, which is useful for commissioning purposes. When
booting from the eMMC, always boot from it as it is not possible to
boot from the SD interface directly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The SDHCI1 is the primary boot controller on rev. 2.1 SoM, which
is the version available on the market. Swap the controller order
to match this and future versions of the SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Init the controllers, otherwise the board cannot boot from SD/MMC.
This boot option is new on rev. 2.1 SoM .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The CAN controllers need slight delay between toggling of their reset
line. Move this action into board_init(), otherwise timer will not be
initialized and the board might hang.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
According to the datasheet, sequential mapping is used for DDR
SDRAM, while interleaved mapping is used for regular SDRAM.
Incorrect configuration of this bit does indeed cause sporadic
memory instability.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
ARC HS Development Kit board is a new low-cost
development platform sporting ARC HS38 in real silicon
with nice set of features such as:
* Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz
* 4Gb of DDR (we use only lowest 1Gb out of it now)
* Lots of DesigWare peripherals
* Different connectivity modules:
- Synopsys HAPS HT3
- Arduino-compatible connector
- MikroBUS
This initial commit supports the following peripherals:
* UART (DW 8250)
* Ethernet (DW GMAC)
* SD/MMC (DW Mobile Storage)
* USB 1.1 & 2.0
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
since commit 842778a091 dfu-util shows serial="UNDEFINED".
to see here again a serial number, we have to call
g_dnl_set_serialnumber().
Signed-off-by: Heiko Schocher <hs@denx.de>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Otherwise the loaded image would miss the efi_runtime sections, and fall
over hard when grub (for example) tried to call runtime services located
in this section.
Signed-off-by: Rob Clark <robdclark@gmail.com>
On the controlcenterd_36BIT_SDCARD config we get a warning about
prg_stage1_prepare being unused. Move the declaration closer to usage
and hide under the existing #if tests.
Cc: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
GPIO bank E pin 8 & 9 are used to control the on-board two USB ports
VBUS on/off. Let's configure them in the misc_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
The topic-miamilite SoM contains a Zynq xc7z010 SoC, 1GB DDR3L RAM,
64MB dual-parallel QSPI NOR flash and clock sources.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init* contain sleep.h header which is not present in u-boot.
Instead of keep comment sleep.h in psu_init* it is easier to add empty
file which is included.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
since commit
'd5abcf94c7123167725fc22ace342f0d455093c1' -
ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
MMC boot on brxre1 board is broken, with this commit we make our board
working again.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.
NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable DHCP command by default. Move environmental variable location
to before U-Boot image. Enlarge reserved mem for malloc. Update
maintainer.
Signed-off-by: York Sun <york.sun@nxp.com>
commit 0650798824 ("board: am335x: Introduce scale_vcores")
updated voltages of each board based on efuse. It updated
beagle bone specific voltages under the condition board_is_bone().
But this is true only for BeagleBoneWhite. Due to which voltages
are not configured for BBB, BBW as wrong device is being probed.
So create a common function board_is_beaglebonex() which includes
am335x based beagle family. Use this for updating voltages.
Also remove extra if condition for selecting voltages which is
done later using a switch case and match usb current limit as
before the commit 0650798824.
Fixes: 0650798824 ("board: am335x: Introduce scale_vcores")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM572x-evm using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 and am572x_gp_evm_A2b_sr1p1
that were autogenerated on 30th January, 2017 by
"Ahmad Rashed <a-rashed@ti.com>" and "Tom Johnson <thjohnson@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM571x-IDK board using latest PMT[1] and the
board files named am571x_idk_v1p3b_sr2p0 that were autogenerated on
23rd March, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_idk_v1p3b_sr2p0 that were autogenerated on
30th January, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.
Details:
- Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
OMAP4/5), so we can obtain status register in common way
- For now ctrl structure for AM33xx/OMAP3 contains only status register
address
- Run hw_data_init() in order to assign ctrl to proper structure
- Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
(DEVICE_TYPE_MASK and GP_DEVICE are used instead)
- Guard structs in omap_common.h with #ifdefs, because otherwise
including omap_common.h on non-omap4/5 board files breaks compilation
Buildman script was run for all OMAP boards. Result output:
arm: (for 38/616 boards)
all +352.5
bss -1.4
data +3.5
rodata +300.0
spl/u-boot-spl:all +284.7
spl/u-boot-spl:data +2.2
spl/u-boot-spl:rodata +252.0
spl/u-boot-spl:text +30.5
text +50.4
(no errors to report)
Tested on AM57x EVM and BeagleBoard xM.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add ddr voltage rail (dcdc3) configuration. Set the dcdc3
DDR supply to 1.35V.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The SoPine is a SoM by Pine64, with an Allwinner A64 SoC, a LPDDR3 DRAM
chip, an AXP803 PMIC, a SPI NOR Flash and a MicroSD slot. The card
detect pin of the MicroSD slot is broken, however, it doesn't matter as
the design of SoPine didn't allow hot-swapping the MicroSD card (The
MicroSD slot is at the back of the SoM, and when the SoM is installed on
the baseboard, it's nearly impossible to remove the MicroSD).
The official baseboard of it is a board with nearly the same connectors
with the original Pine64+, with the MicroUSB power jack replaced, and
at the position of MicroSD slot a eMMC module slot is added.
Add support for SoPine with the official baseboard by adding its
defconfig file. It still uses the device tree of Pine64, however, it
will change after a proper device tree of SoPine with baseboard is
accepted by Linux mainline.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Update board/sunxi/MAINTAINERS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The usb_gadget_handle_interrupts()-function is already implemented by
drivers/usb/gadget/dwc2_udc_otg.c, so we need to avoid defining it
in the evb-rk3328.c board-specific file.
This change fixes the following build error (from buildman):
drivers/usb/gadget/built-in.o: In function `usb_gadget_handle_interrupts':
build/../drivers/usb/gadget/dwc2_udc_otg.c:850: multiple definition of `usb_gadget_handle_interrupts'
board/rockchip/evb_rk3328/built-in.o:build/../board/rockchip/evb_rk3328/evb-rk3328.c:37: first defined here
make[1]: *** [u-boot] Error 1
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update maintainer to Kever Yang for William Zhang is not
work for this board now.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Generate a MAC address based on the cpuid available in the efuse
block: Use the first 6 byte of the cpuid's SHA256 hash and set the
locally administered bits. Also ensure that the multicast bit is
cleared.
The MAC address is only generated and set if there is no ethaddr
present in the saved environment.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With our efuse driver for the RK3399 ready, we can add the
board-specific code that consumes the cpuid from the efuse block and
postprocesses it into the system serial (using the same CRC32 based
derivation as in Linux).
We expose the cpuid via two distinct environment variables:
serial# - the serial number, as derived in Linux
cpuid# - the raw 16 byte CPU id field from the fuse block
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Disable SDRAM controller EMIF2 for single core SOC
Set SDRAM size size to 1GB
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Switch to using <configs/ti_armv7_omap.h> and family. This lets us
drop lots of custom defines.
- Ensure that our default environment uses DEFAULT_LINUX_BOOT_ENV so
that Linux will boot correctly.
- Enable CONFIG_DISTRO_DEFAULTS
- Switch to using CONFIG_OF_CONTROL
- Various other cleanups to match other SoCs in the family line.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family. In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations. Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient. Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still. As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it. We also remove a bunch
of other untested code about changing the speed the DDR runs at.
Signed-off-by: Tom Rini <trini@konsulko.com>
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT
Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.
Signed-off-by: York Sun <york.sun@nxp.com>
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.
Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a sandbox board to test the non-livetree build (i.e. with
CONFIG_OF_FLAT disabled). This increases our build and test coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_DM_MMC_OPS and CONFIG_BLK for all Tegra devices. This moves
Tegra to use driver model fully for MMC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.
BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply
For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").
Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
NOTICE: Configuring AXP PMIC
NOTICE: PMIC: setup successful
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
