We need to update gd in assamble code after relocate,
this is a fix to:
adc421e arm: move gd handling outside of C code
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
It can be useful to record how long tests take; this can help debug slow
running test systems or track changes in performance over time. Enhance
the test system to record timestamps while running test:
- Whenever a new log file section is started.
- After U-Boot is started and communication has been established.
- After each host or U-Boot command is executed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix clock division factor initialization for RCC_PLLCFGR
registers.
PLLR bits (bit 31-28) in RCC_PLLCFGR must not be cleared,
it's a forbidden value. So update RCC_PLLCFGR using
clrsetbits_le32() to set only necessary bits fields.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert this driver to driver model.
This driver is also used by VEXPRESS platforms which doesn't
use driver model.
Tested on STM32F746 and STM32F769 platforms.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update arm_pl180_mmci_init() prototype by adding struct mmc**
param. This is needed before converting this driver to driver model
in order to use arm_pl180_mmci_init() in driver model and in none
driver model implementation
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This option provides better performance and should really always be
enabled. Make this be default y.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch adds support for the Internal RMII Ethernet PHY on the
Amlogic P212 Reference Board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.
The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
Make them a wrapper of scripts/dtc/libfdt/*. This is exactly what
Linux does to sync libfdt. In order to make is possible, import
<linux/libfdt.h> and <linux/libfdt_env.h> from Linux 4.14-rc5.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
The fdt_region.c is U-Boot own file.
I did not touch them in order to avoid unpredictable impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add this typedef in the same place as in Linux. This is necessary
to refactor libfdt inclusion.
U-Boot also defines it in include/compiler.h. Of course it should
not do that, but I do not want to open a can of worms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Prior to this commit, tools/Makefile pulls all libfdt files from
lib/libfdt.
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
This commit changes them to #include ones from scripts/dtc/libfdt.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
I did not touch them in order to avoid unpredictable impact.
The fdt_region.c is U-Boot own file. This is also borrowed from
lib/libfdt/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fortunately, U-Boot did not modify libfdt_internal.h locally.
Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be
periodically synced with the upstream DTC (or kernel).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fortunately, U-Boot did not modify fdt.h locally.
Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be
periodically synced with the upstream DTC (or kernel).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, pylibfdt is always compiled if swig is installed on your
machine. It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.
"checkbinman" and "checkdtoc" are wrong. It is odd that the final
build stage checks if we have built necessary tools. If your platform
depends on dtoc/binman, you must be able to build pylibfdt. If swig
is not installed, it should fail immediately.
I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be
property select:ed by platforms that need them. Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pylibfdt is used by dtoc (and, indirectly by binman), but there
is no reason why it must be generated in the tools/ directory.
Recently, U-Boot switched over to the bundled DTC, and the directory
structure under scripts/dtc/ now mirrors the upstream DTC project.
So, scripts/dtc/pylibfdt is the best location.
I also rewrote the Makefile in a cleaner Kbuild style.
The scripts from the upstream have been moved as follows:
lib/libfdt/pylibfdt/setup.py -> scripts/dtc/pylibfdt/setup.py
lib/libfdt/pylibfdt/libfdt.i -> scripts/dtc/pylibfdt/libfdt.i_shipped
The .i_shipped is coped to .i during building because the .i must be
located in the objtree when we build it out of tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds the following commits from upstream:
b1a6003 tests: Add a test for overlays syntactic sugar
737b2df overlay: Add syntactic sugar version of overlays
497432f checks: Use proper format modifier for size_t
22a65c5 dtc: Bump version to v1.4.5
c575d80 Add fdtoverlay to .gitignore
b6a6f94 fdtoverlay: Sanity check blob size
8c1eb15 pylibfdt: Use Python2 explicitly
ee3d26f checks: add interrupts property check
c1e7738 checks: add gpio binding properties check
b3bbac0 checks: add phandle with arg property checks
[ sync with Linux commit: 4201d057ea91c3d6efd2db65219bc91fae413bc2 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
libfdt has gained some new files. We need to include them in the
kernel's copy.
Reported-by: Kyle Yan <kyan@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[ Linux commit: 4322323058f010274564006d61945187a15b6361 ]
This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Add the Amlogic Meson GXL pinctrl support based on the GXBB driver and
the synchronized DTS from Linux 4.13.5
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5
In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
All current ClearFog SOMs have the SPI flash populated. Enable SPI flash in
the device tree.
Add an alias to the SPI bus so that the 'sf' command can probe the flash on
bus 1.
Add the "spi-flash" compatible string to make the standard SPI flash driver
probe the device.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The production variant of the SPI flash used by the clearfog
devices are based on winbond chips. Additionally enable
SPI_FLASH_BAR since some variants will have 16MB of flash
that requires this to be enabled.
Remove the default speed and mode; these values are taken from the
device tree when CONFIG_DM_SPI_FLASH is enabled.
Add default bus, so that 'sf' detects the SPI flash by default.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: remove speed/mode; add bus; move winbond to defconfig]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the driver by default for the clearfog boards since the external
port is configured for XHCI.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: split from the SoC setup patch]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This fixes the USB 3.0 support for the a38x SOC.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This makes the initial changes need to support the
a38x series of SOCs. It adds the device-tree identifier
as well as changing the board_support function to take
the IO address designated by device-tree.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t; update 37xx and 8K implementations]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable DISTRO_DEFAULTS for
mvebu_db_armada8k_defconfig
mvebu_mcbin-88f8040_defconfig
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Update help message for "mac" command to reflect correct descriptions
and parameters.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Distro boot support gives flexibility to run distro RFS like Ubuntu
being deployed from SD card or SATA drive. If it fails to detect
external storage, fall back to qspi/sd boot.
Enable this by default in RDB's defconfig by selecting
CONFIG_DISTRO_DEFAULTS
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Zhang Ying <zhangying@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently the chipselect used to identify the corresponding NAND chip
is stored at the controller and only set during fsl_ifc_chip_init().
This way, only the last NAND chip is working, as the previous value
of cs_nand gets overwritten.
In order to solve this issue the chipselect is computed on demand by
evaluating the bank variable. Thus, the correct chipselect for each
NAND chip operation is used.
Tested on hardware with two NAND chips connected to the IFC
controller.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Scott Wood <oss@buserror.net>
[YS: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The zero value returned from qbman_swp_acquire() is an error
condition meaning no free buffer for allocation.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kushwaha Prabhakar <prabhakar@freescale.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
