This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.
The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.
Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.
Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will get printed. If the device is detected, the board will get
resetted so that an easy loop test can be done. The board will reboot
until the PCIe device is not detected.
Signed-off-by: Stefan Roese <sr@denx.de>
Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the default of currently 2
is used. Values from 0...3 are possible (2 bits).
In this case of the theadorable board, PEX interface 0 needs a value
of 0 for the detection pulse width so that the PCIe device (Atheros
WLAN PCIe device) is consistantly detected.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.
Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Adam Shobash <adams@marvell.com>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove DM_I2C_COMPAT from the board configurations for
Armada 37xx platform boards for supressing the buid tim
warning.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Bypass XHCI and AHCi board configuration flow on ESPRESSOBin
community board.
The community board does not have i2c expander and USB VBUS
is always on, so the scan for AHCi and USB devices can be
faster without unneded configurations.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add initial default configuration for Marvell ESPRESSOBin
community board based on Aramda-3720 SoC
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Implement the board-specific network init function for
ESPRESSOBin community board, setting the on-board Topaz
switch port to forward mode and allow network connection
through any of the available Etherenet ports.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix the default pin control values in a board-specific
function on early board init stage.
This fix allows the NETA driver to work in RGMII
mode until the full-featured pin control driver gets
introduced.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes for North and South bridges to
Armada-37xx DT
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable mvebu bubt command support on A3720 DB
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable support for Marvell Ethernet PHYs on A37xx platforms
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add default configuration for MACHHIATOBin community board
based on Aramda-8040 SoC.
Change-Id: Ic6b562065c0929ec338492452f765115c15a6188
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y
Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously, dtoc could only process the top-level nodes which led to
device nodes in hierarchical trees to be ignored. E.g. the mmc0 node
in the following example would be ignored, as only the soc node was
processed:
/ {
soc {
mmc0 {
/* ... */
};
};
};
This introduces a recursive helper method ScanNode, which is used by
ScanTree to recursively parse the entire tree hierarchy.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
commit 2f11cd9121 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Enable SPL_DM on all AM43xx based platforms
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable DM_I2C/SPI/ETH for all AM43XX based boards.
Enable it using imply keyword so that a user can
disable this when not needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add u-boot specific dtsi for am43xx-gp-evm so
that it will be used for SPL.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add u-boot specific dtsi so that this will be
included automatically while building dts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To make SPL_OF_CONTROL work on OMAP2+ SoCs, _image_binary_end must be
defined in the linker script along with CONFIG_SPL_SEPARATE_BSS.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Calls to IS_ENABLED() on a non-y/n option will always be false, even
when set. We can correct this by adding a new bool value that is set
based on the conditions required for SPL_STACK_R_MALLOC_SIMPLE_LEN to be
set instead.
Fixes: 340f418acd ("spl: Add spl_early_init()")
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Changes in v2:
- Fix thinko pointed out by Lokesh
Add support for the Broadcom Northstar2 SoC and SVK (bcm958712k). The
BCM5871X is a series of quad-core 64-bit 2GHz ARMv8 Cortex-A57
processors targeting a broad range of networking applications.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
When building u-boot tools in cross-build environment CFLAGS environment
variable set up for target is taken into an account when building code
for host. Make it empty on invocation of python.
This fixes the following build errors when cross-compiling for xtensa:
cc1: error: unrecognized command line option "-mlongcalls"
cc1: error: unrecognized command line option "-mauto-litpools"
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The CAAM in IMX parts doesn't support public key hardware acceleration
(PKHA), so don't use RSA_FREESCALE_EXP. If you try to use it on IMX
(assuming you have the clocks enabled first) you will get back an
"Invalid KEY Command" error since PKHA isn't a valid key destination for
these parts.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, AM43xx just re-uses the version strings from AM33xx which is
wrong; the actual values for AM43xx are different. Fix this by adding
a separate version string array for AM43xx and use this instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
* Add note that execution needs Python development package installed
* Standardize on upper case "FIT", "FDT" as necessary for clarity
* Fix "tempoerary", "linex" typos
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
This adds documentation on the u-boot,efi-partition-entries-offset
property (which overrides CONFIG_EFI_PARTITION_ENTRIES_OFF, if
present).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This moves the description of the /config node from README.fdt-control
into a separate file doc/device-tree-bindings/config.txt.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some architectures require their SPL loader at a fixed address within
the first 16KB of the disk. To avoid an overlap with the partition
entries of the EFI partition table, the first safe offset (in bytes,
from the start of the device) for the entries can be set through
CONFIG_EFI_PARTITION_ENTRIES_OFF (via Kconfig)
When formatting a device with an EFI partition table, we may need to
leave a gap between the GPT header (always in LBA 1) and the partition
entries. The GPT header already contains a field to specify the
on-disk location, which has so far always been set to LBA 2. With this
change, a configurable offset will be translated into a LBA address
indicating where to put the entries.
Now also allows an override via device-tree using a config-node (see
doc/device-tree-bindings/config.txt for documentation).
Tested (exporting an internal MMC formatted with this) against Linux,
MacOS X and Windows.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: __maybe_unused on config_offset to avoid warning]
Signed-off-by: Tom Rini <trini@konsulko.com>