Move this option to Kconfig and set its default value to 4; this
increases the number of supported CPUs for some boards.
It consumes 1KB memory per CPU for PSCI stack, but it should not
be a big deal, given the amount of memory used for the modern OSes.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms
can select. Then, move CONFIG_ARMV7_PSCI, which is automatically
enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no reason to duplicate code for DRA7xx platforms as there
can be Rail grouping. The maximum voltage detection algorithm can still
be run on other platforms with no Rail grouping and does not harm as
it gives the same result.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
gpio_en field is introduced to detect if pmic is controlled by GPIO.
Make this field 0 on all TPS659* pmics available on DRA7/OMAP5 based platforms
and remove the #ifndefs.
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Linux stopped the use of keyword 'boolean' in Kconfig.
Refer to commit 6341e62b212a2541efb0160c470e90bd226d5496 ("kconfig:
use bool instead of boolean for type definition attributes")
in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Flush operations need to be cacheline aligned to take effect, make
sure to flush always complete cachelines. This avoids messages such
as:
CACHE: Misaligned operation at range [00900000, 009004d9]
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features. At this point in time they no longer serve a good purpose so
remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of testing booting Linux kernels on Rockchip devices, it was
discovered by Ziyuan Xu and Sandy Patterson that we had multiple and for
some cases incomplete isb definitions. This was causing a failure to
boot of the Linux kernel.
In order to solve this problem as well as cover any corner cases that we
may also have had a number of changes are made in order to consolidate
things. First, <asm/barriers.h> now becomes the source of isb/dsb/dmb
definitions. This however introduces another complexity. Due to
needing to build SPL for 32bit tegra with -march=armv4 we need to borrow
the __LINUX_ARM_ARCH__ logic from the Linux Kernel in a more complete
form. Move this from arch/arm/lib/Makefile to arch/arm/Makefile and add
a comment about it. Now that we can always know what the target CPU is
capable off we can get always do the correct thing for the barrier. The
final part of this is that need to be consistent everywhere and call
isb()/dsb()/dmb() and NOT call ISB/DSB/DMB in some cases and the
function names in others.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Sandy Patterson <apatterson@sightlogix.com>
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reported-by: Sandy Patterson <apatterson@sightlogix.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, hence
update QSPI input clock divider value (DPLL_PER_HS13) to provide 76.8MHz
clock, so that driver can use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This commit adds support for the Toradex Computer on Modules
Colibri iMX7S/iMX7D. The two modules/SoC's are very similar hence
can be easily supported by one board. The board code detects RAM
size at runtime which is one of the differences between the two
boards. The board also uses the UART's in DTE mode, hence making
use of the new DTE support via serial DM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This patch implements PSCI functions for ls102xa SoC following PSCI v1.0,
they are as the list:
psci_version,
psci_features,
psci_cpu_suspend,
psci_affinity_info,
psci_system_reset,
psci_system_off.
Tested on LS1021aQDS, LS1021aTWR.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The input parameter CPU ID needs to be validated before furher oprations such
as CPU_ON, this patch introduces the function to do this.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds all the PSCI v1.0 functions in to the common framework, with
all the functions returning "not implemented" by default, as a common framework
all the dummy functions are added here, it is up to every platform developer to
decide which version of PSCI and which functions to implement.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
A couple of commits have modified the am33xx/am437x ddr2/ddr3
initialization path to fix certain issues, but have had the side effect
of causing L3 noc errors during initialization. The two commits are:
69b918 "am33xx,ddr3: fix ddr3 sdram configuration"
fc46ba "arm: am437x: Enable hardware leveling for EMIF"
The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all
platforms. This delays initialization and refresh until a later stage.
The 500us timer can be programmed for platforms that require it
and for platforms that don't require it. It is currently hardcoded
for 400MHz systems. For systems with a higher memory frequency
this needs to be a larger value, and for systems with a lower
memory frequency this can be a lower value. This can be
considered a separate issue and corrected in a later commit.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The delay needs to be before the write to ref_ctrl register
which initiates refreshes. An improper initialization sequence
generates an L3 noc error.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that
causes the build to break when that option is not active. Fix this issue
by only building the u-boot_HS.img target when building U-Boot into an
actual FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit e29878f introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM43xx high-security (HS) devices that causes the
build to break when that option is not active. Fix this issue by only
building the u-boot_HS.img target when building U-Boot into an actual
FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
identify_nand_chip hangs forever in loop when NAND is not present.
As IGEPv2 comes either with NAND or OneNAND flash, add reset timeout
to let function fail gracefully allowing caller to know NAND is
not present. On NAND equipped board, reset succeeds on first read,
so 1000 loops seems to be safe timeout.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
According to the IMX6DQRM Reference Manual, the description
of bit 7 (axi_alt_sel) of the CCM_CBCDR register is:
"AXI alternative clock select
0 pll2 396MHz PFD will be selected as alternative clock for AXI root clock
1 pll3 540MHz PFD will be selected as alternative clock for AXI root clock "
The current logic is inverted, so fix it to match the reference manual.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Set the enable-method in the cpu node to PSCI, and create device
node for PSCI, when PSCI was enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use existing Kconfig symbols to let the user configure whether to
build a U-Boot with non-secure mode support or not. This also allows
to enable virtualization extension easily.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This can be useful if the same U-Boot binary is used for boards
available with a i.MX 7Solo and i.MX 7Dual.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have a secure data section for storing variables, there
should be no need for platform code to get the stack address.
Make psci_get_cpu_stack_top a local function, as it should only be
used in armv7/psci.S and only by psci_stack_setup.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we have a secure data section and space to store per-CPU target
PC address, switch to it instead of storing the target PC on the stack.
Also save clobbered r4-r7 registers on the stack and restore them on
return in psci_cpu_on for Tegra, i.MX7, and LS102xA platforms.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we have a data section, add helper functions to save and fetch
per-CPU target PC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi and i.mx7 both define the __secure modifier to put functions in
the secure section. Move this to a common place.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
psci_text_end was used to calculate the PSCI stack address following the
secure monitor text. Now that we have an explicit secure stack section,
this is no longer used.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we have a secure stack section that guarantees usable memory,
allocate the PSCI stacks in that section.
Also add a diagram detailing how the stacks are placed in memory.
Reserved space for the target PC remains unchanged. This should be
moved to global variables within a secure data section in the future.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch finishes the rewrite of sunxi specific PSCI parts into C
code.
The assembly-only stack setup code has been factored out into a common
function for ARMv7. The GIC setup code can be renamed as psci_arch_init.
And we can use an empty stub function for psci_text_end.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Every platform has the same stack setup code in assembly as part of
psci_arch_init.
Move this out into a common separate function, psci_stack_setup, for
all platforms. This will allow us to move the remaining parts of
psci_arch_init into C code, or drop it entirely.
Also provide a stub no-op psci_arch_init for platforms that don't need
their own specific setup code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
At present armv7 will unhappily invalidate a cache region and print an
error message. Make it skip the operation instead, as it does with other
cache operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Errata i727 is applicable on all OMAP5 and DRA7 variants but enabled only
on OMAP5 ES1.0. So, enable it on all platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modify the SPL build procedure for AM437x high-security (HS) device
variants to create a secure u-boot_HS.img FIT blob that contains U-Boot
and DTB artifacts signed (and optionally encrypted) with a TI-specific
process based on the CONFIG_TI_SECURE_DEVICE config option and the
externally-provided image signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds commands so that when a secure device is in use and the SPL is
built to load a FIT image (with combined U-Boot binary and various
DTBs), these components that get fed into the FIT are all processed to
be signed/encrypted/etc. as per the operations performed by the
secure-binary-image.sh script of the TI SECDEV package. Furthermore,
perform minor comments cleanup to make better use of the available
space.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds an API that verifies a signature attached to an image (binary
blob). This API is basically a entry to a secure ROM service provided by
the device and accessed via an SMC call, using a particular calling
convention.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a generic C-callable API for making secure ROM calls on OMAP and
OMAP-compatible devices. This API provides the important function of
flushing the ROM call arguments to memory from the cache, so that the
secure world will have a coherent view of those arguments. Then is
simply calls the omap_smc_sec routine.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
