This patch adds support for the Voipac PXA270 board. The support includes:
- Ethernet
- USB
- MMC
- NOR Booting
- OneNAND Booting
- LCD
- HDD
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
The SPI env code didn't support redundant environments until recently, but
this code was written before that. Since it has never been tested (and
currently causes a build failure), simply punt it. If the functionality
is actually desired, it can be re-added once it has been tested.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The original BF518F-EZBRD's have a Micrel KSZ8893 DSA on them, but newer
ones only have a National PHY (which lack a RX Error interrupt line). So
in the board eth init code, dynamically detect what is hooked up to the MAC
and handle each accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than only support the pins dedicated as chip selects, utilize the
gpio framework to support any gpio pin.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add edminiv2 board support for mv_egiga.
Add edminiv2 config to enable mv_egiga.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rename all references to kirkwood in mvgbe symbols
throughout the whole codebase.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The example configuration files of nios2-generic board can generated
binary to run on the EP1C20, EP1S10, and EP1S40 boards. So the three
boards can be removed.
With nios2-generic approach, the fpga parameter header file can
be generated from hardware designs using tools. Porting u-boot for
nios2 boards is simplified. Vendors can supply their fpga parameter
file or patches to add a new nios2-generic board instance. There is
no need to include other boards support for nios2 in the u-boot
mainline.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
* the following problems are met :
config was set to use the new driver as a default but
- RMII was not enabled for the new driver
- the new driver didn't compile with RMII enabled
- the new driver initialize a PHY at address O when the PHY of
this board is at 1 thus we get "AT91 EMAC RMII: No PHY present"
* to fix these problems, this patch :
- enable RMII for the new driver
- fix the wrong define used in the at91_emac.c
- allow the config file to set a default phy address (and use
0 as a default as in the actual at91_emac.c driver)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch add support for the ve8313 board based on
Freescale MPC8313 CPU.
- serial console on UART 1
- 128 MB DDR RAM
- 32 MB NOR Flash
- 16 MB NAND Flash
- Ethernet MII Mode over on TSEC0
- micrel ksz804 phy
- Hardware WDT MAX824
changes since v1
- Environment size = sector size
- use red. environment
- add comments from Kim Phillips
- add MAKEALL, MAINTAINERS entry
- Codingstyle issues fixed
- inserted original Copyrights
- PCI subsys vendor ID changed from 0x1057 (Motorola)
to 0x1957 (Freescale)
changes since v2
- add comments from Wolfgang Denk
- fix Codingstyle and some comments
- reworked WDT reset (just toggling the WD_TRIG pin)
- Environment size now 16KiB
- fixed RAMBOOT version
- fixed CONFIG_SYS_LOAD_ADDR
- renamed CONFIG_TSEC1_NAME to TSEC1
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch provides support for MPC8308RDB development board from
Freescale with a minimal set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
The following features are enabled in configuration but not fully tested:
I2C (used to get the board revision)
I2C-connected RTC
VSC7385 switch
There is one (hopefully) minor issue: on soft reset the board sometimes
resets twice. I've not managed to find the fix for this problem yet.
As a workaround instruction cache can be disabled.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the new GPIO framework code in both the Blackfin arch and the
nand_plat driver to simplify things greatly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
OMAP4 Panda is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU
This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4430 SDP is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU
This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9
Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.
The two architectures are similar enough that substantial code can be shared.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Now that we have a unified gpio layer, the different status led
implementations can be switched to the common gpio led driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When boards define CONFIG_BOARD_SPECIFIC_LED, the common led definitions
are OK for Blackfin boards. So switch the few boards using these over to
the common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that we have a unified gpio layer, the misc partial gpio commands
can be unified and made complete (support all possible gpios).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Remove some INFERNO related #ifdef's from common environment code by
fixing the board configuration settings (add CONFIG_ENV_SECT_SIZE).
While we are at it, fix comment which incorrectly talks about 4 KB
environment size, while it's actually 0x4000 = 16 KiB.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rolf Offermanns <rof@sysgo.de>
On P2020RDB eTSEC2 is connected to Vitesse VSC8221 PHY via SGMII.
Current TBI PHY settings for SGMII mode cause link problems on
this platform, link never comes up.
Fix this by making TBI PHY settings configurable and add a working
configuration for P2020RDB.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Because the variable was getting defined twice.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality. Change all this to use CONFIG_SYS_BUS_CLK consistently.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Eran Man <eran@nbase.co.il>
Cc: Stefan Roese <sr@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h.
Because of this, EMAC does not work on EVMs which do not have phy
connected at 1. Moving the macro to board config file makes this
configurable depending on where the phy is connected on the MDIO bus.
This patch fixes the board reset issue observed during network access
on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1
but it is 0 on DM365EVM.
This patch is verified on da830/omap-l137, dm365 and dm644x evms.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Conflicts:
CONFLICT (rename/add): Rename
board/davinci/da830evm/Makefile->board/ti/tnetv107xevm/Makefile
in 89b765c7f6.
board/ti/tnetv107xevm/Makefile added in HEAD
But files were identical, so no problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for the LaCie ED Mini V2 product
which is based on the Marvell Orion5x SoC.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
This patch adds support for the Samsung Goni board (S5PC110 SoC)
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Provides initial support for TI OMAP-L138/DA850 SoC devices on
a Logic PD EVM board.
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The EVMS have been shipping with NAND (instead of OneNAND) as default.
So, this patch sets NAND as default.
To choose OneNAND, define CMD_ONENAND instead of CMD_NAND in the
config file omap3_evm.h.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
