Enable the gpio support (driver and command)
in the configuration of the board bcm968380gerg
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable the gpio controllers in the device tree
of the board bcm968380gerg.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add gpio controllers in bcm6838 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This driver is used on several big endian mips board.
So we could use raw I/O function instead of forcing
big endian access.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
S17 ethernet support is for QCA8337N, which used on
AP152 (QCA9563) board. It is a 7 ports GbE switch.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2-v3:
- add more commit message for s17
Changes for v4-v5:
- coding style cleanup
QCA9563 is CPU used on AP152 board :
Clock speed : 750 MHz ,
Arch : Mips 74Kc,
Eth : SGMII interface,
MIMO config : 3 * 3 450M,
2 * USB 2.0,
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2:
- coding style cleanup
- remove ununsed flash chip in defconfig
- enable automatic icache / dcache size in defconfig
Changes for v3:
- add detailed information for qca956x in commit message
Changes for v4:
- remove pre-configured network settings in ap152.h
Changes for v5:
- coding style cleanup
See details in chapter 8.6.2 and 8.6.4 (page 140-141) of qca9563 datasheet,
NFRAC[17:0]
So the mask of [17:5] is 0x1fff not 0x3fff.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2-v3:
- add more information for this commit
Changes for v4-v5:
- coding style cleanup
The function mscc_miim_reset resets all the phys, but it is called for
each phy separetely. One consequence of this is that the boot time
is increased by 2 seconds.
The fix consists for calling the mscc_miim_reset function only once for
all phys.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove the function boot_reloc_ramdisk in the file arch/mips/lib/bootm
because it is relocating again the ramdisk. The function do_bootm_states()
already relocates the ramdisk even if it is a legacy uImage or a FIT image.
The relocation in the function do_bootm_states() was introduce in the
commit c2e7e72bb9 ("bootm: relocate ramdisk
if CONFIG_SYS_BOOT_RAMDISK_HIGH set")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch changes Gardena to the correct GARDENA spelling. Also the
platform name is "GARDENA smart Gateway". This patch changes the
incorrect occurrances.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The new mtd is very useful so let's enable it on the LinkIt Smart
7688 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jiri Kastner <cz172638@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Currently enabling fsck on FAT16/FAT32 exposes that we have problems
with:
TestFsBasic.test_fs13[fat16]
TestFsBasic.test_fs11[fat32]
TestFsBasic.test_fs12[fat32]
TestFsBasic.test_fs13[fat32]
TestFsExt.test_fs_ext1[fat32]
TestFsExt.test_fs_ext2[fat32]
TestFsExt.test_fs_ext3[fat32]
TestFsExt.test_fs_ext4[fat32]
TestFsExt.test_fs_ext5[fat32]
TestFsExt.test_fs_ext6[fat32]
TestFsExt.test_fs_ext7[fat32]
TestFsExt.test_fs_ext8[fat32]
TestFsExt.test_fs_ext9[fat32]
TestMkdir.test_mkdir6[fat16]
TestMkdir.test_mkdir1[fat32]
TestMkdir.test_mkdir2[fat32]
TestMkdir.test_mkdir3[fat32]
TestMkdir.test_mkdir4[fat32]
TestMkdir.test_mkdir5[fat32]
TestMkdir.test_mkdir6[fat32]
TestUnlink.test_unlink1[fat16]
TestUnlink.test_unlink2[fat16]
TestUnlink.test_unlink3[fat16]
TestUnlink.test_unlink4[fat16]
TestUnlink.test_unlink5[fat16]
TestUnlink.test_unlink6[fat16]
TestUnlink.test_unlink7[fat16]
TestUnlink.test_unlink1[fat32]
TestUnlink.test_unlink2[fat32]
TestUnlink.test_unlink3[fat32]
TestUnlink.test_unlink4[fat32]
TestUnlink.test_unlink5[fat32]
TestUnlink.test_unlink6[fat32]
TestUnlink.test_unlink7[fat32]
This is because we don't update the "information sector" on FAT32.
While in the future we should resolve this problem and include that
feature, we should enable fsck for ext4 to ensure that things remain in
good shape there.
Signed-off-by: Tom Rini <trini@konsulko.com>
Ext4 allows for arbitrarily sized block group descriptors when 64-bit
addressing is enabled, which was previously not properly supported. This
patch dynamically allocates a chunk of memory of the correct size.
Signed-off-by: Benjamin Lim <jarsp.ctf@gmail.com>
Add option to the mmc rd test to check the duration of the
execution of the mmc read command. This allows intercepting
read performance regressions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test for 'mmc info' subcommand. This tests whether the card
information is obtained correctly and verifies the device, bus
speed, bus mode and bus width.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test for 'mmc rescan' subcommand. This tests whether the
system can switch to a specific card and then rescan the card.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add separate test for 'mmc dev' subcommand. This tests whether
the system can switch to a specific card.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Factor out the 'mmc dev' call so it can be recycled by other tests.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
A FAT12/FAT16 root directory location is specified by a sector offset and
it might not start at a cluster boundary. It also resides before the
data area (before cluster 2).
However, the current code assumes that the root directory is located at
a beginning of a cluster, causing no files to be found if that is not
the case.
Since the FAT12/FAT16 root directory is located before the data area
and is not aligned to clusters, using unsigned cluster numbers to refer
to the root directory does not work well (the "cluster number" may be
negative, and even allowing it be signed would not make it properly
aligned).
Modify the code to not use the normal cluster numbering when referring to
the root directory of FAT12/FAT16 and instead use a cluster-sized
offsets counted from the root directory start sector.
This is a relatively common case as at least the filesystem formatter on
Win7 seems to create such filesystems by default on 2GB USB sticks when
"FAT" is selected (cluster size 64 sectors, rootdir size 32 sectors,
rootdir starts at half a cluster before cluster 2).
dosfstools mkfs.vfat does not seem to create affected filesystems.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Tested-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Hi,
when I try to load a sparse file via ext4load, I am getting the error message
'invalid extent'
After a deeper look in the code, it seems to be an issue in the function ext4fs_get_extent_block in fs/ext4/ext4_common.c:
The file starts with 1k of zeros. The blocksize is 1024. So the first extend block contains the following information:
eh_entries: 1
eh_depth: 1
ei_block 1
When the upper layer (ext4fs_read_file) asks for fileblock 0, we are running in the 'invalid extent' error message.
For me it seems, that the code is not prepared for handling a sparse block at the beginning of the file. The following change, solved my problem:
I am really not an expert in ext4 filesystems. Can somebody please have a look at this issue and give me a feedback, if I am totally wrong or not?
Test cases are:
1) basic link creation, verify it can be followed
2) chained links, verify it can be followed
3) replace exiting file a with a link, and a link with a link. verify it
can be followed
4) create a broken link, verify it can't be followed
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The command line is:
ln <interface> <dev[:part]> target linkname
Currently symbolic links are supported only in ext4 and only if the option
CMD_EXT4_WRITE is enabled.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Re-use the functions used to write/create a file, to support creation of a
symbolic link.
The difference with a regular file are small:
- The inode mode is flagged with S_IFLNK instead of S_IFREG
- The ext2_dirent's filetype is FILETYPE_SYMLINK instead of FILETYPE_REG
- Instead of storing the content of a file in allocated blocks, the path
to the target is stored. And if the target's path is short enough, no block
is allocated and the target's path is stored in ext2_inode.b.symlink
As with regulars files, if a file/symlink with the same name exits, it is
unlinked first and then re-created.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix ext4 env code]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no need to modify the buffer passed to ext4fs_write_file().
The memset() call is not required here and was likely copied from the
equivalent part of the ext4fs_read_file() function where we do need it.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We need to make sure that file writes,file creation, etc. are properly
performed and do not corrupt the filesystem.
To help with this, introduce the assert_fs_integrity() function that
executes the appropriate fsck tool. It should be called at the end of any
test that modify the content/organization of the filesystem.
Currently only supports FATs and EXT4.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the metadata checksums are enabled, all write operations will fail.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When a file contains extents, U-Boot currently reads extent-related data
for each block in the file, even if that data is located in the same
block each time. This significantly slows down loading of files that use
extents. Implement a very dumb cache to prevent repeatedly reading the
same block. Files with extents now load as fast as files without.
Note: There are many cases where read_allocated_block() is called. This
patch only addresses one of those places; all others still read redundant
data in any case they did before. This is a minimal patch to fix the
load command; other cases aren't fixed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
v2018.01 commit e23eb942ad ("ARM: rmobile: Stop using
rcar-common/common.c on Gen3") removed
board/renesas/rcar-common/common.c from the build chain with the
reasoning that calling arch_preboot_os() is no longer needed.
However, it left the arch_preboot_os() in place. Get rid of it.
This is done in preparation of resurrecting rcar-common/common.c.
NOTE: The three removed header includes (io.h, sys_proto.h, rcar-mstp.h)
are in direct relationship with the dropped arch_preboot_os() hook. The
other headers (common.h, rmobile.h) are going to be needed by pretty
much anything that is going to appear in the rcar common code. So, keep
the two in place.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
The E2 Alt board has two USB ports, add missing DT nodes to make the
USB available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Increase the USB power good delay on Alt, this is required with
certain USB sticks, otherwise they might not be detected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Synchronize R-Car Gen3 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen3 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Linux 5.0, commit 1c163f4c7b3f621efff9b28a47abb36f7378d783,
has a TDSEL fix for R8A7790 H2 and R8A7794 E2 SoCs, implement
similar fix for U-Boot. The difference here is that the SoC
ES matching has to be implemented manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add defconfig and board specific adjustments for the R8A77965 M3N ULCB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pin control tables for R8A77965 from Linux 5.0 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add clock tables for R8A77965 from Linux 5.0 , except for the
crit, R and Z clock, which are neither used nor supported by
the U-Boot clock framework yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
