UCLASS_MTD is a better fit for NAND drivers.
Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c
Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, the denali NAND driver in U-Boot configures the
SPARE_AREA_SKIP_BYTES based on the CONFIG option.
Recently, Linux kernel merged a patch that associates the proper
value for this register with the DT compatible string.
Do likewise in U-Boot too.
The denali_spl.c still uses CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When the reset signal is de-asserted, the HW-controlled bootstrap
starts running unless it is disabled in the SoC integration.
It issues some commands to detect a NAND chip, and sets up registers
automatically. Until this process finishes, software should avoid
any register access.
Without this delay function, some of UniPhier boards hangs up while
executing nand_scan_ident(). (denali_read_byte() is blocked)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Denali NAND driver in mainline Linux currently cannot deassert the
reset. The upcoming Linux 5.6 will support the reset controlling, and
also set up SPARE_AREA_SKIP_BYTES correctly. So, the Denali driver in
the future kernel will work without relying on any bootloader or firmware.
However, we still need to take care of stable kernel versions for a while.
U-boot should not assert the reset of this controller.
Fixes: ed784ac382 ("mtd: rawnand: denali: add reset handling")
Signed-off-by: Marek Vasut <marex@denx.de>
[yamada.masahiro: reword the commit description]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The "nand_x" and "ecc" clocks are currently optional. Make the core
clock optional in the same way. This will allow platforms with no clock
driver support to use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de> # On SoCFPGA Arria V
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.
This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.
This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.
This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for Octal flash devices. Octal flash devices use 8 IO lines
for data transfer. Currently only 1-1-8 Octal Read mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Linux has supported W25N01GV for a long time, so lets import it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove hardcoded base addresses of smc controller and nand controller.
Get those addresses from dt and replace wherever they are used.
Remove smc and nand base address from header file too.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove hardcoded base address of nand and replace it with the
value taken from device tree. Remove base address from header
file too.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Make changes to arasan nand driver to move it to driver model.
Select DM_MTD if arasan nand driver is selected.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Static checker warns 'ret' variable may be used uninitialized in
spi_nor_erase() and spi_nor_write() in case of zero length requests.
Fix these warnings by checking for zero length requests and returning
early.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add gd25q128 128Mbit chip to spi-nor id table.
Tested on Pinebook Pro
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JESD216 allow vendors to define their own SFDP tables.
Add SST SFDP parser. The vendor table is allocated using resource-managed
kmalloc - the table will be freed on driver detach. It will be accessible
by getting the UCLASS_SPI_FLASH's private data.
The SST's SFDP table is particularly of interest because contains
pre-programmed globally unique EUI-48 and EUI-64 identifiers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
With of-platdata we need to create drivers for particular chips, or at
least drivers that are separate from the standard code, since C structures
are created by dtoc which are private to that driver.
To avoid duplicating the probing code, export this probe function for use
by these drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).
Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is already the case that all defconfigs with SPI_FLASH_MTD also
declare using MTD, but let's make this consistent and enforce it in
Kconfig. Most of the time SPI_FLASH_MTD is used in conjunction with
UBI, which already depends on MTD.
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Because of the include's game, when some files are compiled for a SPI
NAND device, no warning appears. But when it is for a raw NAND device,
GCC complains. Fix these warning by including <common.h>.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The array 'mtd_table' is unused in the code. Remove this as gcc doesn't
always discard unused global variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
- Add I2C clocks for i.MX6Q CCF driver
- Fix check in clk_set_default_parents()
- Managed API to get clock from device tree
- Fixes for core clock code (including sandbox regression tests)
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.
This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add an entry for the Adesto AT25SL321 SPI NOR chip.
This SPI NOR chip is found in the Embedded Artist i.MX7ULP COM board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.
Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).
We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.
We do this all in one patch to guarantee bisectibility.
This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
n25q* and mt25q* (both 256Mb and 512Mb) flashes support Flag status
register that indicates various errors that may be encountered during
erase/write operations. Therefore add USE_FSR flag wherever missing.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
mt25q* flashes support stateless 4 byte addressing opcodes. Add entries
for the same. These flashes have bit 6 set in 5th byte of READ ID
response when compared to n25q* variants.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Per datasheets of n25q256* and n25q512* not all variants of n25q256* and
n25q512* support 4 Byte stateless addressing opcodes. Therefore drop
SPI_NOR_4B_OPCODES flag from these entries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot uses CONFIG_SPI_FLASH_USE_4K_SECTORS to enable 4K small sector
support. Use that instead of MTD_SPI_NOR_USE_4K_SECTORS.
Reported-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use dev_err() when reporting reason for erase/write failures so that
users can be made aware of the reason for failure.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To allow SPI_FLASH_MTD being enabled separately in SPL we add a new
option. The only user currently is the stm32mp15_basic board.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
DM_SPI_FLASH should require spi flash interface code for dm
version, so imply SPI_FLASH core by default if any board
enabled DM_SPI_FLASH.
This overcome the explicit enablement of CONFIG_SPI_FLASH on
respective boards when DM_SPI_FLASH being used.
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add is25wp256, chip to spi-nor id table.
Tested on SiFive FU540 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>