The UHS modes are not supported in beagle-x15 because it's not possible to
switch the IO lines supply voltage to 1.8v.
Also HS200 cannot be supported on mmc2, because the IO lines of mmc2 are
connected to 3.3v.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the new compatible string "ti,dra7-hsmmc" that was specifically
added for dra7 and dra72. This is required since for dra7 and dra72
processors iodelay values has to be set unlike other processors.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
To debug device tree issues involving 32- and 64-bit platforms, it is useful to
have a generic 64-bit platform available.
Add a version of the sandbox that uses 64-bit integers for its physical
addresses as well as a modified device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Added CONFIG_SYS_TEXT_BASE to configs/sandbox64_defconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dtc produces these warnings when compiling sandbox:
arch/sandbox/dts/test.dtb: Warning (gpios_property):
Could not get phandle node for /base-gpios:num-gpios(cell 0)
arch/sandbox/dts/test.dtb: Warning (gpios_property):
Missing property '#gpio-cells' in node /reset-ctl or bad phandle
(referred from /extra-gpios:num-gpios[0])
Both are due to it assuming that the 'num-gpios' property holds a phandle
pointing to a GPIO node.
To avoid these warnings, rename the sandbox property so that it does not
include the string 'gpios'.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dtc produces these warnings when compiling sandbox:
arch/sandbox/dts/test.dtb: Warning (reg_format): "reg" property in /chosen/chosen-test has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
arch/sandbox/dts/test.dtb: Warning (avoid_default_addr_size): Relying on default #address-cells value for /chosen/chosen-test
arch/sandbox/dts/test.dtb: Warning (avoid_default_addr_size): Relying on default #size-cells value for /chosen/chosen-test
Add the missing properties to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: f200680 (dm: core: parse chosen node)
Only ARM and in some configs MIPS really implement arch_fixup_fdt().
Others just use the same boilerplate which is not good by itself,
but what's worse if we try to build with disabled CONFIG_CMD_BOOTM
and enabled CONFIG_OF_LIBFDT we'll hit an unknown symbol which was
apparently implemented in arch/xxx/lib/bootm.c.
Now with weak arch_fixup_fdt() right in image-fdt.c where it is
used we get both items highlighted above fixed.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Enable I2C6 bus on Porter to access the PMIC , ie. to reset the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix ommission where the u-boot,dm-pre-reloc DT bit was pulled into the
common DT, not the U-Boot specific DT part. Move it to U-Boot DT part.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Those two nodes are needed to configure pinmux before relocation
and to configure clock before relocation, since CPG/MSSR needs
access to RST node. This is not noticable on Gen3, but on Gen2
this causes problems in SPL if they are not available early.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Make the SCIF available before relocation and in SPL on R8A7791 Porter.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Kconfig should only 'select' features that are required for an arch.
Standard features that can be disabled without breaking board support
should use 'imply' instead, to allow users to disable it.
These options are changed for mach-socfpga:
- DM_SPI & DM_SPI_FLASH: only required with QSPI support enabled
- SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION: the boot rom supports a
partitionless mode also, where SPL is located at address 0
- HW_WATCHDOG: while all mainline board defconfigs use it, U-Boot
should still work without it.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
All Socfpga boards from ./include/configs/socfpga_* define
CONFIG_HW_WATCHDOG.
To ease CONFIG_HW_WATCHDOG conversion to Kconfig select it in
config ARCH_SOCFPGA (arch/arm/Kconfig) section.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
This patch adds "spi-flash" to the compatible list of the qspi flash
chip for all socfpga boards. This is required to make qspi work on
these boards on top of the recent fixes. Without the "spi-flash"
compatible string for the flash chip, the speed cannot be read and a
speed of 0Hz is used (which results in a divide-by-zero on these
boards).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
ARC Elf32 tools by default enable usage of so-called "small data"
section or in ARC PRM parlance "GP-relative addressing".
The idea is to put up to 2kB of frequently used data into a separate
location and use indirect addressing via dedicated core register (GP).
Where GP is used as a base for offset calculation.
And so if "-msdata" toggle is passed to the compiler either explicitly
or implicitly (that's Elf32 tools case) it will try to put some data
in that "small data" area and then to calculate real offset from GP
to be encoded in instructions we need to know the base value which
liker gets from __SDATA_BEGIN__ symbol in hte linker script.
In U-Boot we don't use that feature and linker script doesn't define
__SDATA_BEGIN__ which gives us the following linkage error if we use
Elf32 tools:
------------------------->8-------------------
LD u-boot
.../bin/arc-elf32-ld.bfd: Error: Linker symbol __SDATA_BEGIN__ not found
.../bin/arc-elf32-ld.bfd: final link failed: Bad value
------------------------->8-------------------
Note if uClibc or glibc tools are used that problem doesn't happen
because usage of "small data section" is disabled by default as not very
useful for bigger executables. Moreover GP is just another name of r26
so we're loosing 1 core register which is not used by the compiler as a
generic register with "-msdata".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ATF recently began announcing PSCI v1.1. Since that version is unknown
to u-boot, the PSCI device nodes were not updated.
Switch from the case statement to a greater/less-than comparison so that
v1.1, as well as future versions, get at least the compatible nodes of
known versions.
PSCI v1.1 doesn't seem to have introduced a new corresponding compatible.
Signed-off-by: Andre Heider <a.heider@gmail.com>
When this config is enabled, <asm/arch/boot0.h> is included,
but the Kconfig help says this should be a define
(ARM_SOC_BOOT0_HOOK).
The code for this in arch/arm/lib/vectors.s was changed on
01/02/2017 with commit ce62e57fc5 ("ARM: boot0 hook: remove macro,
include whole header file").
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Commit 6808ef9ac2 ("move booti_setup to arch/arm/lig/image.c")
not only moved the code, but also replaced a tab with 4 spaces
to break the Linux coding style.
Restore tab indentation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Chen <bin.chen@linaro.org>
This driver is no longer used on any supported platform in U-Boot and
there is no interest in maintaining it further from people that have
used it historically.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
c: Alexey Brodkin <alexey.brodkin@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Fix build warning in arch/microblaze/lib/bootm.c with gcc 7.3.0:
warning: this 'if' clause does not guard... [-Wmisleading-indentation]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Fix build warning in arch/arm/mach-omap2/emif-common.c and
arch/arm/mach-omap2/omap4/emif.c with gcc 7.3.0:
warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Before the patch an undefined constant EFI_SUBSYSTEM was used in the
crt0 code. The current version of binutils does not swallow the error.
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=888403
The necessary constant IMAGE_SUBSYSTEM_EFI_APPLICATION is already
defined in pe.h. So let's factor out asm-generic/pe.h for the
image subsystem constants and use it in our assembler code.
IMAGE_SUBSYSTEM_SAL_RUNTIME_DRIVER does not exist in the specification
let's use IMAGE_SUBSYSTEM_EFI_ROM instead.
The include pe.h is only used in code maintained by Alex so let him be the
maintainer here too.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
config_phylib_all_drivers.h should be included when CONFIG_PHYLIB and
CONFIG_TSEC_ENET are defined.
Fixes: 3146f0c017 ("Move PHYLIB to Kconfig")
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove dependency of SYS_HAS_SERDES for Layerscape Chasis 2 and
Layerscape Chasis 3.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
Simplify SPL_LDSCRIPT config by using the new arch Kconfig
configurations ARCH_MX23 and ARCH_MX28.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The motivation for moving MX28 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The motivation for moving MX23 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
