Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Check whether user has explicitly defined device and partition where
environment file will be located before using 'auto' i.e. bootable
partition
Voids the need to set such partition as bootable to work with the
'dev:auto' tuple
Signed-off-by: Manuel Reis <mluis.reis@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
Try to initialize emmc in board_late_init() and if it fails then we know
that emmc device is not connected.
This allows to use in U-Boot just one DTS file for all Espressobin variants
and also to correctly set fdtfile env variable for Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Reviewed-by: Andre Heider <a.heider@gmail.com>
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a9 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add Luka Perkov to Puzzle-M801 BOARD MAINTAINERS.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Upstream linux DT naming doesn't align with the U-Boot DT, which may
not always be the case so this allows using BOOTENV_EFI_SET_FDTFILE_FALLBACK
where it might be appropriate for some boards.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For booting via UEFI we need to define the fdtfile option so
bootefi has the option to load a fdtfile from disk. For arm64
the kernel dtb is located in a vendor directory so we define
that as nvidia for that architecture.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use gpio_early_init_uart() function to disable RS232 serial transceiver
ForceOFF# pins on Iris.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Avoid UART input from floating RX pins on UARTB and UARTC (Colibri T30)
and UARTB, UARTC and UARTD (Apalis T30).
Note: Floating pins may cause spurious break conditions potentially
interrupting U-Boot's autoboot.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix SPI1 and UART2/3 resp. UARTB/C pinmuxing.
Note: The former was illegally muxing multiple SoC balls onto the same
internal SoC signal which caused rather strange behaviour regarding
the RS232 serial transceiver ForceOFF# pins as available on Iris.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add pinmuxing comment stating that TRISTATE means the output driver is
tri-stated and INPUT means the input driver is enabled vs. OUTPUT where
it is disabled.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was used for a board which is not supproted anymore and can
therefore be dropped.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This option is obsolete since 2009 and can be removed globally.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Kontron SMARC-sAL28 board uses that flash.
This is the same change as in the linux commit f3418718c0ec ("mtd:
spi-nor: Add support for w25q32jwm").
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Leo Krueger <leo.krueger@zal.aero>
Since update_flash() is used only in update_tftp(), it should be
guarded with appropriate config options.
After the commit 3149e524fc, common/update.c will be built under
either CONFIG_UDATE_TFTP, CONFIG_DFU_TFTP or CONFIG_UPDATE_FIT.
Since CONFIG_UPDATE_FIT, hence fit_update(), doesn't rely on
update_flash(), the compiler may cause an "unused" warning if
CONFIG_UPDATE_FIT=y and CONFIG_UPDATE_TFTP=n and CONFIG_DFU_TFTP=n.
This is, for example, the case for sandbox defconfig where
EFI_CAPSULE_FIRMWARE_FIT is enabled for test purpose.
Fixes: 3149e524fc ("common: update: add a generic interface for FIT
image")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This comment is in the wrong format, so reports an error with
'make htmldocs'. Fix it.
Fixes: a294ead8d2 ("dm: Use an allocated array for run-time device info")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This comment is in the wrong format, so reports an error with
'make htmldocs'. Fix it.
Fixes: b73d61a556 ("x86: zimage: Add a little more logging")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It seems nobody tested the debug() option in spin_lock_irqsave().
Currently, when #define DEBUG, it spoils the compiler with
In file included from drivers/usb/dwc3/gadget.c:18:
drivers/usb/dwc3/gadget.c: In function ‘dwc3_gadget_set_selfpowered’:
include/log.h:235:4: warning: ‘flags’ is used uninitialized in this function [-Wuninitialized]
235 | printf(pr_fmt(fmt), ##args); \
| ^~~~~~
drivers/usb/dwc3/gadget.c:1347:17: note: ‘flags’ was declared here
1347 | unsigned long flags;
| ^~~~~
and so on...
Drop useless debug() call to make compiler happy.
Fixes: 0c06db5983 ("lib, linux: move linux specific defines to linux/compat.h")
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
timeout should be in "millisecond" instead of second,
so divided it by 1000 when calculate the load value.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
The origin patch didn't have this change and it was caused by manual
resolution where additional backslash was added.
Fixes: 6723b4c6ca ("binman: Call helper function binman_set_rom_offset() to fill offset")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The test should be checking whether $flags are non-zero and $drv_flags
contain specific flags, however these two sets of flags are separate,
and the two tests should be logically ANDed, not bitwise ANDed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 6900797678 ("cros_ec: Support keyboard scanning with
EC_CMD_GET_NEXT_EVENT") the cros-ec-keyb driver has started using this
command, but the sandbox EC emulator does not recognize it and
continuously prints:
** Unknown EC command 0x67
This patch makes the sandbox driver send basic responses to the command,
but the response only supports keyboard scans for now.
The EC side of this command stores and returns events from a queue, and
returns -EC_RES_UNAVAILABLE when there are no new events. This should be
possible to implement by hooking into the SDL event queue (perhaps via
sandbox_sdl_poll_events). Implementing that is a bit harder to do since
the existing sandbox code is discarding pending keyboard events, then
reading the current keyboard state.
Since the EC emulator never explicitly fails to work on this command,
the fallback to the older command will not trigger and will not be
tested anymore.
Fixes: 6900797678 ("cros_ec: Support keyboard scanning with EC_CMD_GET_NEXT_EVENT")
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present if CROSS_COMPILE contains a tilde, such as
~/.buildman-toolchains/gcc-7.3.0-nolibc/i386-linux/bin/i386-linux-gcc
then binman gives a confusing error:
binman: Error 255 running '~/..buildman-toolchains/gcc-7.3.0- ...
Fix this by expanding it out before running the tool.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a tool to update or insert an Octeon specific header into the U-Boot
image. This is needed e.g. for booting via SPI NOR, eMMC and NAND.
While working on this, move enum cvmx_board_types_enum and
cvmx_board_type_to_string() to cvmx-bootloader.h and remove the
unreferenced (unsupported) board definition.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Using ram_get_info() is complicated and does not work after relocation.
Now that gd->ram_size holds the full RAM size, let's use it instead and
remove the ram_get_size logic completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With this patch, gd->ram_size now holds to full RAM size detected by the
DDR init code. It introduces the get_effective_memsize() function to
report the maximum usable RAM size in U-Boot to the system instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Don't use "platdata_auto_alloc_size" but "priv_auto_alloc_size" instead
to auto allocate the private data struct, which is referenced via
dev_get_priv() in this driver. This fixes an ugly bug detected while
trying to boot via SPI NOR.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Octeon has a specific boot header, when booted via SPI NOR, NAND or MMC.
Here the only 2 instructions are allowed in the first few bytes of the
image. And these instructions need to be one branch and a nop. This
patch adds the necessary nop after the nop, to that the common MIPS
image is compatible with this Octeon header.
The tool to patch the Octeon boot header into the image will be send in
a follow-up patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The following errors are corrected:
* Linux crash when accessing UEFI variables at runtime.
* UEFI variable using standalone MM on 32 bit systems
not working due to missing packing of communication
structure
* NULL dereference when FAT16 root directory is full
* FAT files with a short file name starting with 0xE5 (0x05 in directory
entry) where treated as deleted.
The UEFI SetTime() service is enabled on ARM QEMU.
-----BEGIN PGP SIGNATURE-----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=CgpH
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc3-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc3 (3)
The following errors are corrected:
* Linux crash when accessing UEFI variables at runtime.
* UEFI variable using standalone MM on 32 bit systems
not working due to missing packing of communication
structure
* NULL dereference when FAT16 root directory is full
* FAT files with a short file name starting with 0xE5 (0x05 in directory
entry) where treated as deleted.
The UEFI SetTime() service is enabled on ARM QEMU.
commit 1fabfeef506c ("efi_loader: parameter check in GetNextVariableName()")
introduces a check using u16_strnlen(). This code is used on EFI
runtime variables as well, so unless we mark it as runtime, the kernel
will crash trying to access it.
Fixes: 1fabfeef506c ("efi_loader: parameter check in GetNextVariableName()")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Pack struct efi_mm_communicate_header as done in EDK2 as seen in
release 201808 [1]. If not packed sizeof() for the structure adds
4 additional bytes on 32bit targets which breaks the ABI.
Link: [1] https://github.com/tianocore/edk2/blob/edk2-stable201808/MdePkg/Include/Protocol/MmCommunication.h#L21
Fixes: 23a397d2e2 ("efi_loader: Add headers for EDK2 StandAloneMM communication")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Enable EFI_SET_TIME on the sandbox and QEMU ARM to ensure that we compile
and test the relevant code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Using constants instead of anonymous numbers increases code readability.
Fixes: 704df6aa0a ("fs: fat: refactor write interface for a file offset")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Patrice Chotard