PCI I/O space is currently mapped 1:1 at 0xFA000000. Linux requires
PCI I/O space to start at 0 on the PCI bus. This patch maps PCI I/O
space such that 0xFA000000 in the processor's address space maps to 0
on the PCI I/O bus.
Signed-off-by Randy Vinson <rvinson@mvista.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
fix mvBL-M7 config and move to matrix_vision subdir
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add the ability for the MPC8349EMDS to run in PCI Agent mode, acting as a
PCI card rather than a host computer.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change the MPC8349EMDS board to use the generic PCI initialization code
for the mpc83xx cpu.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fix build warnings @ mvBC-P board by using correct types, i.e. change
out_be32 to out_be16 and out_8 accordingly.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
There is no point in disabling the icache on 7xx/74xx/86xx parts and not
also flushing the icache. All callers of invalidate_l1_instruction_cache()
call icache_disable() right after. Make it so icache_disable() calls
invalidate_l1_instruction_cache() for us.
Also, dcache_disable() already calls dcache_flush() so there is no point
in the explicit calls of dcache_flush().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Remove non-common flash driver in
board/freescale/m54455evb/flash.c. The non-cfi flash will
use CONFIG_FLASH_CFI_LEGACY to configure the flash
attribute.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Fixing leading white spaces
- Fixing indentation where 4 spaces are used instead of tab
- Removing C++ comments (//), wherever I introduced them
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Correct the mx31_gpio_mux() function to allow changing all i.MX31 IOMUX
contacts instead of only the first 256 ones as is the case prior to
this patch.
Add missing MUX_* macros and update board files to use the new macros.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
The recent change to move the .bss outside of the image gives older
binutils (ld from eldk4.1/binutils-2.16) some headache:
ppc_85xx-ld: u-boot: Not enough room for program headers (allocated 3, need 4)
ppc_85xx-ld: final link failed: Bad value
We workaround it by being explicit about the program headers and not
assigning the .bss to a program header.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the Favr-32 board made by EarthLCD.
This kit, which is also called ezLCD-101 when running with EarthLCD firmware,
has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash,
Ethernet, audio out, USB device, SD-card slot, USART and various other
connectors for cennecting stuff to SPI, I2C, GPIO, etc.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
TASREG is ColdFire platform, the include ppc4xx.h in
board/esd/common/flash.c causes conflict.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
* Move to using absolute addressing always. Makes the scripts a bit more
portable and common
* Moved .bss after the end of the image. These allows us to have more
room in the resulting binary image for code and data.
* Removed .text object files that aren't really needed
* Make sure _end is 4-byte aligned as the .bss init code expects this.
(Its possible that the end of .bss isn't 4-byte aligned)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Relocate the location of U-Boot in the flash
- Save the environment in one sector of the flash memory
- MTD Support
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
For more information see: http:///www.miromico.com/hammerhead
Signed-off-by: Julien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
Renamed initialization functions for atngw100 and atstk1000.
Removed initializations for these boards from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
among others:
-Virtex 5 FX FPGA (With a ppc440x5 in it)
-256MB of SDRAM2
-32MB of Flash
-I2C Eeprom
-System ACE chip
-Serial ATA connectors
-RS232 Level Conversors
-Ethernet Transceiver
This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash
- Includes Changes propossed by Stefan Roese and Michal Simek
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
The thinko was quite silly indeed, I messed with !ptr. Normally this
would trigger some fault, but in U-Boot NULL pointer is equal to phys
0, so the code was working still, just didn't actually test mpc8315erdb
environment variable value. Heh.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Freescale ships MPC8315E-RDB boards either with TSEC1 and USB UTMI
support, or without TSEC1 but with USB ULPI PHY support in addition.
With this patch user can specify desired USB PHY.
Also, it seems that we can't distinguish the two boards in software, so
user have to set `mpc8315erdb' environment variable to either 'tsec1'
(TSEC1 enabled) or `ulpi' (board with ULPI PHY, TSEC1 disabled), so that
Linux will not probe for TSEC1.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update the sys_eeprom.c file to handle both NXID and CCID EEPROM formats. The
NXID format replaces the older CCID format, but it's important to support both
since most boards out there still use the CCID format. This change is in
preparation for using one file to handle both formats. This will also unify
EEPROM support for all Freescale 85xx and 86xx boards.
Also update the 86xx board header files to use the standard CFG_I2C_EEPROM_ADDR
instead of ID_EEPROM_ADDR.
Signed-off-by: Timur Tabi <timur@freescale.com>
Add in for the sbc8560, the ft_board_setup() routine, based on what is
in use for the Freescale MPC8560ADS board.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The sbc8560 board ships with 512MB of memory installed,
but the current cs0_bnds is hard coded for 256MB. Set the
value based on CFG_SDRAM_SIZE.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The 8544 DS doesn't have any cacheable Local Bus memories set up. By mapping
space for some anyway, we were allowing speculative loads into unmapped space,
which would cause an exception (annoying, even if ultimately harmless).
Removing LBC_CACHE_BASE, and using LBC_NONCACHE_BASE for the LBC LAW solves the
problem.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Signed-off-by: Stefan Roese <sr@denx.de>
On the at91sam9260ep development board there is an EEPROM
connected to the TWI interface (PA23, PA24 Peripheral A
multiplexing), so we cannot use these pins as ETX2, ETX3.
This patch configures PA10, PA11 pins for ETX2, ETX3
instead of PA23, PA24 pins.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Manuel Sahm <Manuel.Sahm@feig.de>
The DIU_DIV register is 8 bit not 5 bit. This prevented large DIV values
so it was not possible to set a slow pixel clock and thus prevented
display on small screens.
Signed-off-by: Kenneth Johansson <kenneth@southpole.se>
Acked-by: John Rigby <jrigby@freescale.com>
board/ads5121/iopin.c
Replace bit fields in struct iopin_t with a single
field and intialize it via plain old macros.
This fixes the type pun warnings and makes the code
more readable.
board/ads5121/ads5121.c
Add include iopin.h to ads5121.c for the iopin_initialize
prototype.
Add an extern void ads5121_diu_init(void)
Signed-off-by: John Rigby <jrigby@freescale.com>
