- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Add USB OTG ID pin mux and switch the USB OTG port
from peripheral to OTG mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DH DRC02 board has an on-board microSD slot,
add DT properties to enable the slot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Check whether user has explicitly defined device and partition where
environment file will be located before using 'auto' i.e. bootable
partition
Voids the need to set such partition as bootable to work with the
'dev:auto' tuple
Signed-off-by: Manuel Reis <mluis.reis@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
Use the full name of firmware self extracting file to make it run.
Also, don't use sudo when not needed.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Try to initialize emmc in board_late_init() and if it fails then we know
that emmc device is not connected.
This allows to use in U-Boot just one DTS file for all Espressobin variants
and also to correctly set fdtfile env variable for Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Reviewed-by: Andre Heider <a.heider@gmail.com>
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a9 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add Luka Perkov to Puzzle-M801 BOARD MAINTAINERS.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Add implementation of board_mem_get_layout for overriding the memory
layout.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Introduce weak function board_mem_get_layout() which allows overriding
the memory layout from board code in runtime, useful for handling
different SKU versions.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This documents the u-boot build and deployment procedure.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Introduce initial hierarchy of device trees for Apalis iMX8X
System on Module.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
the mem_map structure containing the size of SDRAM is used in various
cache functions in cache_v8.c thus we need to update it with the
sdram size the board is configured with as well. Without this
the cache functions do not get setup properly and can hang
in the case where a board reports more SDRAM than defined in
PHYS_SDRAM_SIZE.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Implement board_phys_sdram_size() to automatically detect Verdin iMX8M
Mini DualLite 1GB vs. Verdin iMX8M Mini Quad 2GB.
Note: This only works if we keep using similar RAM chips!
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Now with them first Verdin iMX8M Mini DualLite modules in for bring-up
we got clarity how is_cpu_type() actually behaves.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Enable PCA9450 i2c level translator, as this is used for the
on module ADC.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
And select the correct devicetree accordingly by setting the variant
environment variable.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
V1.1A HW switched the PMIC from BD71837 to PCA9450.
- Disable combined DVS in PCA9450_BUCK123_DVS.
- Increase DDR Voltage to 0.95V as we use a 1.5GHz RAM.
- Configure WDOG_B behaviour.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The I2C address is 0x25, not 0x35. This according to the datasheet and
tests with a PCA9450A.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
For imx usdhc/esdhc, once set the DDR_EN, enable the DDR mode, the
card clock will be divied by 2 automatically by the host. So need
to first config the DDR_EN correctly, then update the card clock.
This will make sure the actual card clock is as our expected.
IC also suggest config the DDR_EN firstly, then config the clock
divider.
For HS400/HS400ES mode, need to config the strobe dll, this need
to based on the correct target clock rate, so need to do this after
clock rate is update.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
add the dts file to the MAINTAINERS entry
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Set `bootcause' from b850v3 power management watchdog status.
Boot cause "REVERT" is no longer used, remove it.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reduce vital product data size to match the latest specification.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use VPD product ID instead of confidx, so that we can easily reuse the
product ID defines and avoid some magic numbers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove pinmux defines, that are no longer used after
converting the code to devicetree.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix typo in NFS command configuration check.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Commit f692b479f0 changed the VPD partition name from "vpd" to
"vpd@0". Fix the VPD reader code to use the new name, so that
the VPD code keeps working.
Fixes: f692b479f0 ("i2c: eeprom: Use reg property instead of offset and size")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following warning:
arch/arm/mach-imx/imx8/ahab.c:105:3: warning: implicit declaration of function ‘flush_dcache_range’ [-Wimplicit-function-declaration]
flush_dcache_range(s, e);
^~~~~~~~~~~~~~~~~~
Include cpu_func.h header which declares the flush_dcache_range()
function.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Fix those by using "%lu" specified.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
Fix those by using %llx
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
