In rk3328, some function pin may have more than one choice, and muxed
with more than one IO, for example, the UART2 controller IO,
TX and RX, have 3 choice(setting in com_iomux):
- M0 which mux with GPIO1A0/GPIO1A1
- M1 which mux with GPIO2A0/GPIO2A1
- usb2phy which mux with USB2.0 DP/DM pin.
We should not decide which group to use in pinctrl driver,
for it may be different in different board, it should goes to board
file, and the pinctrl file should setting correct iomux depends on
the com_iomux value.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move GRF register bit definition into GRF header file, remove
'GRF_' prefix and add 'GPIOmXn_' as prefix for bit meaning.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
U-Boot prefer to use MASKs with SHIFT embeded, clean the Macro
definition in grf header file and pinctrl driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- hclk/pclk_div range should use '<=' instead of '<'
- use GPLL for pd_bus clock source
- pd_bus HCLK/PCLK clock rate should not bigger than ACLK
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Embeded the shift in mask MACRO definition in cru header file
and clock driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver to support iomux setup for the most commonly
used peripherals on rk3368.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver to setup the various PLLs and peripheral
clocks on the RK3368.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
At present common.h includes various ARM-specific headers. In preparation
for dropping this, add a few explicit declarations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within arm's u-boot.h header.
Also drop the comment about something to be fixed. It has been there
forever and it is not clear what it means.
Signed-off-by: Simon Glass <sjg@chromium.org>
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX. It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family. In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations. Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient. Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still. As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it. We also remove a bunch
of other untested code about changing the speed the DDR runs at.
Signed-off-by: Tom Rini <trini@konsulko.com>
Loading PPA in SPL puts the rest of U-Boot (including RAM version
loaded later) in EL2 with MMU and cache enabled. Once PPA is loaded,
PSCI is available.
Signed-off-by: York Sun <york.sun@nxp.com>
The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and
is built on layerscape architecture. It is 40-pin derivative of
LS2084A (non-AIOP personality of LS2088A). So feature-wise it is
same as LS2084A. LS2041A is a 4-core personality of LS2081A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_HASH
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_ESBC_VALIDATE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch updates the mksunxiboot tool to optionally add
the default device tree name string to the SPL header. This
information can be used by the firmware upgrade tools to
protect users from harming themselves by trying to upgrade
to an incompatible bootloader.
The primary use case here is a non-removable bootable media
(such as NAND, eMMC or SPI flash), which already may have
a properly working, but a little bit outdated bootloader
installed. For example, the user may download or build a
new U-Boot image for "Cubieboard", and then attemept to
install it on a "Cubieboard2" hardware by mistake as a
replacement for the already existing bootloader. If this
happens, the flash programming tool can identify this
problem and warn the user.
The size of the SPL header is also increased from 64 bytes
to 96 bytes to provide enough space for the device tree name
string.
[Andre: split patch to remove OF_LIST hash feature]
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Newer SoCs use same TV encoder unit. Split it out so it can be reused
with new DM video driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there. Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely. The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file. Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead. With that
changed we can drop all defines of CONFIG_OMAP. While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Change tbu/l type to unsigned int.
>From the timer file for arm,
"(((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;" is used,
This piece code is based on tbu/tbl is 32bits, so change the type to
unsigned int.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:
MPU values for PG 2.0 and later(Package ZCZ and ZCE):
-------------------------------------------------------
| | ZCZ | ZCE |
|-------------------------------------------------------|
| | VDD[V] | ARM [MHz] | VDD[V] | ARM [MHz] |
|-------|----------|------------|----------|------------|
| NITRO | 1.325 | 1000 | NA | NA |
|-------|----------|------------|----------|------------|
| TURBO | 1.26 | 800 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP120 | 1.20 | 720 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP100 | 1.10 | 600 | 1.10 | 600 |
|-------|----------|------------|----------|------------|
| OPP50 | 0.95 | 300 | 0.95 | 300 |
-------------------------------------------------------
There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.
[1] http://www.ti.com/lit/ds/symlink/am3356.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cortex-M archs support option memory protection unit (MPU). MPU is used
to set the memory types, attributes, access permissions for different regions,
cache policies of the device.
e.g. using MPU it is possible to configure memory region as device memory
or strongly ordered, memory attributes like execute never, cache policies
like write-back or write-through.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
At present there is not operation to invalidate a cache range. This seems
to be needed to fill out the cache operations. Add an implementation based
on the flush operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Add mipi display mode for rk3399 vop, so that we can use mipi panel
for display.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add GRF register declaration for mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To add HDMI support for the RK3399, this commit provides the needed
pinctrl functionality to configure the HDMI I2C pins (used for reading
the screen's EDID).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are 3 regions used by rk3399 ATF:
- bl31 code, located at 0x10000;
- cortex-m0 code and data, located at 0xff8c0000;
- bl31 data, located at 0xff8c1000 ~ 0xff8c4000;
SPL_TEXT_BASE starts from 0xff8c2000, we need to reserve memory
for ATF data, or else there will be memory corrupt after SPL
loads the ATF image.
More detail about cortex-M0 code in ATF:
https://github.com/ARM-software/arm-trusted-firmware/commit/
8382e17c4c6bffd15119dfce1ee4372e3c1a7890
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
GMAC controller need to init the tx io driver strength to 13mA,
just like the description in dts pinctrl node, or else the controller
may only work in 100MHz Mode, and fail to work at 1000MHz mode.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
Reviewed-by: Simon Glass <sjg@chromium.org>
