Update the ext loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than having a global variable, pass the spl_image as a parameter.
This avoids BSS use, and makes it clearer what the function is actually
doing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Update existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. We need two variants - one for BOOT_DEVICE_CPGMAC and one for
BOOT_DEVICE_USBETH.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Also set up the sunxi function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All the other SPL loaders are in this directory, so move the SPI one in
there too.
There are two board-specific SPI loaders (fsl and sunxi). These remain in
the drivers/mtd/spi directory, since they do not contain generic code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Include updating the DFU case]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a linker list macro which can be used to declare an SPL image loader.
Update spl_load_image() to search available loaders for the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and tidy up existing uses. Also add a function
comment to the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than act on the global variable, pass the required struct in as a
parameter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This format can be flashed directly at address 0 of
the NAND FLASH, as it contains all necessary headers.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Move FASTBOOT_MBR_NAME and FASTBOOT_GPT_NAME into Kconfig.
Add dependency on the FASTBOOT_FLASH setting (also for FASTBOOT_MBR_NAME).
Remove the now redundant GPT_ENTRY_NAME.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add FIXME about xxx_PARTITION needing to be in Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add special target "mbr" (otherwise configurable via CONFIG_FASTBOOT_MBR_NAME)
to write MBR partition table.
Partitions are now searched using the generic function which finds any
partiiton by name. For MBR the partition names hda1, sda1, etc. are used.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far partition search by name has been supported only on the EFI partition
table. This patch extends the search to all partition tables.
Rename part_get_info_efi_by_name() to part_get_info_by_name(), move it from
part_efi.c into part.c and make it a generic function which traverses all part
drivers and searches all partitions (in the order given by the linked list).
For this a new variable struct part_driver.max_entries is added, which limits
the number of partitions searched. For EFI this was GPT_ENTRY_NUMBERS.
Similarly the limit is defined for DOS, ISO, MAC and AMIGA partition tables.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
This bug appears in b6396403 which makes u-boot unable to pass
arguments via bootm to a standalone application without this patch.
Steps to reproduce.
Compile a u-boot. Use mkimage to package the standalone hello_world.bin
file.
e.g. For the MIPS Boston platform
mkimage -n "hello" -A mips -O u-boot -C none -T standalone \
-a 0xffffffff80200000 -d hello_world.bin \
-ep 0xffffffff80200000 hello_out
Then tftp hello_out and run it using
boston # dhcp 192.168.154.45:hello_out
...
boston # bootm $loadaddr 123 321
Without the patch the following output is observed.
boston # bootm $loadaddr 123 321
Image Name: hello
Image Type: MIPS U-Boot Standalone Program (uncompressed)
Data Size: 1240 Bytes = 1.2 KiB
Load Address: 80200000
Entry Point: 80200000
Verifying Checksum ... OK
Loading Standalone Program ... OK
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 0
argv[0] = "0xffffffff88000000"
With the patch, you see the following.
boston # bootm $loadaddr 123 321
Image Name: hello
Image Type: MIPS U-Boot Standalone Program (uncompressed)
Data Size: 1240 Bytes = 1.2 KiB
Load Address: 80200000
Entry Point: 80200000
Verifying Checksum ... OK
Loading Standalone Program ... OK
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 3
argv[0] = "0xffffffff88000000"
argv[1] = "123"
argv[2] = "321"
argv[3] = "<NULL>"
Without the patch, the go command at the entry point seems to work.
boston # go 0xffffffff80200000 123 321
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 3
argv[0] = "0xffffffff80200000"
argv[1] = "123"
argv[2] = "321"
argv[3] = "<NULL>"
Hit any key to exit ...
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Without this, if g_dnl_register() fails, DFU code continues on
blindly and crashes. This fix makes it simply print an error
message instead.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
[l.majewski@samsung.com - some manual tweaks needed]
The cmd_dfu functionality is been used by both SPL and
u-boot, saperating the core dfu functionality moving
it to common/dfu.c.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Traditionally the DFU support is available only
as part 2nd stage boot loader(u-boot) and DFU
is not supported in SPL.
The SPL-DFU feature is useful for boards which
does not have MMC/SD, ethernet boot mechanism
to boot the board and only has USB inteface.
This patch add DFU support in SPL with RAM
memory device support to load and execute u-boot.
And then leverage full functionality DFU in
u-boot to flash boot inital binary images to
factory or bare-metal boards to memory devices
like SPI, eMMC, MMC/SD card using USB interface.
This SPL-DFU support can be enabled through
Menuconfig->Boot Images->Enable SPL-DFU support
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit bac17b78da ("image-fit: switch ENOLINK to ENOENT") changed
fit_get_node_from_config to return -ENOENT when a property doesn't
exist, but didn't change any of its callers which check return values.
Notably it didn't change boot_get_ramdisk, which leads to U-Boot failing
to boot FIT images which don't include ramdisks with the following
message:
Ramdisk image is corrupt or invalid
It also didn't take into account that by returning -ENOENT to denote the
lack of a property we lost the ability to determine from the return
value of fit_get_node_from_config whether it was the property or the
configuration node that was missing, which may potentially lead callers
to accept invalid FIT images.
Fix this by having fit_get_node_from_config return -EINVAL when the
configuration node isn't found and -ENOENT when the property isn't
found, which seems to make semantic sense. Callers that previously
checked for -ENOLINK are adjusted to check for -ENOENT, which fixes the
breakage introduced by commit bac17b78da ("image-fit: switch ENOLINK
to ENOENT").
The only other user of the return fit_get_node_from_config return value,
indirectly, is bootm_find_os which already checked for -ENOENT. From a
read-through of the code I suspect it ought to have been checking for
-ENOLINK prior to bac17b78da ("image-fit: switch ENOLINK to ENOENT")
anyway, which would make it right after this patch, but this would be
good to get verified by someone who knows this x86 code or is able to
test it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jonathan Gray <jsg@jsg.id.au>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Currently we have a mismash of architectures which use arch_cpu_init
from architecture-wide code (arc, avr32, blackfin, mips, nios2, xtensa)
and architectures which use arch_cpu_init from machine/SoC level code
(arm, x86).
In order to clean this mess up & allow for both use cases, introduce a
new mach_cpu_init callback which is run immediately after arch_cpu_init.
This will allow for architectures to have arch-wide code without needing
individual machines to all implement their own arch_cpu_init with a call
to some common function.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the config IDENT_STRING to Kconfig and migrate all boards
[sivadur: Migrate zynq boards]
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[trini: Update configs, add some default to sunxi Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some of the SPL options have TPL equivalents. Add these to Kconfig so that
we can convert these options over to work from Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a lot of SPL options in U-Boot to enable various features and
drivers. Currently these do not use Kconfig. Add them to Kconfig along
with suitable help, and drop them from the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present TPL uses the same options as SPL support. In a few cases the board
config enables or disables the SPL options depending on whether
CONFIG_TPL_BUILD is defined.
With the move to Kconfig, options are determined for the whole build and
(without a hack like an #undef in a header file) cannot be controlled in this
way.
Create new TPL options for these and update users. This will allow Kconfig
conversion to proceed for these boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reworks spl_set_header_raw_uboot to allow having both os boot
(which comes with a valid header) and aborting when no valid header is
found (thus excluding raw u-boot.bin images).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 62afc60188 introduced fpga image load via
bootm but broke the OS check in fit_image_load().
This commit removes following compiler warning:
---8<---
In file included from tools/common/image-fit.c:1:
/Volumes/devel/u-boot/tools/../common/image-fit.c:1715:39: warning: use of logical '||' with constant operand [-Wconstant-logical-operand]
os_ok = image_type == IH_TYPE_FLATDT || IH_TYPE_FPGA ||
^ ~~~~~~~~~~~~
/Volumes/devel/u-boot/tools/../common/image-fit.c:1715:39: note: use '|' for a bitwise operation
os_ok = image_type == IH_TYPE_FLATDT || IH_TYPE_FPGA ||
^~
|
1 warning generated.
--->8---
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
When phy autoneg on, the link speed and duplex should be
determined by phy advertising register and
phy link partner ability register.
Check phy advertising register when geting phy link speed and
duplex if autoneg on.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This improves the cread_line() function so that it will correctly
process the 'Home', 'End', 'Delete' and arrow key escape sequences
produced by various terminal emulators. This makes command line editing
a more pleasant experience.
The previous code only supported the cursor keys and the 'Home' key, and
only for certain terminal emulator configurations. This adds support for
the 'End and 'Delete' keys, and recognises a wider range of escape
sequences. For example, the left arrow key can be 'ESC O D' instead of
'ESC [ D', and the 'Home' key can be 'ESC [ H', 'ESC O H', 'ESC 1 ~' or
'ESC 7 ~', depending on what terminal emulator you use and how it is
configured.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Changes for v2
- Explicitly initialize variable to avoid spurious compiler warning.
Changes for v3
- Remove unnecessary setting of 'act' to ESC_REJECT (now its default
value).
The bootz and booti commands rely on common functionality that is found
in common/bootm.c and common/bootm_os.c. They do not however rely on
the rest of cmd/bootm.c to be implemented so split them into their own
files. Have various Makefiles include the required infrastructure for
CONFIG_CMD_BOOT[IZ] as well as CONFIG_CMD_BOOTM. Move the declaration
of 'images' over to common/bootm.c.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that nand_info[] is an array of pointers we need to ensure that it's
been populated prior to use. We may for example have ENV in NAND set in
configurations that run on boards with and without NAND (where default
env is fine enough, such as omap3_beagle and beagleboard (NAND) vs
beagle xM (no NAND)).
Fixes: b616d9b0a7 ("nand: Embed mtd_info in struct nand_chip")
Cc: Scott Wood <oss@buserror.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Scott Wood <oss@buserror.net>
The Xtensa processor architecture is a configurable, extensible,
and synthesizable 32-bit RISC processor core provided by Cadence.
This is the first part of the basic architecture port with changes to
common files. The 'arch/xtensa' directory, and boards and additional
drivers will be in separate commits.
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The cleanup of the legacy mii registration API that's no longer used now
that the drivers have been converted to use the (more) modern API.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The next patch will call fdt_translate_address() from somewhere with a
"const void *blob" rather than a "void *blob", so fdt_translate_address()
must accept a const pointer too. Constify the minimum number of function
parameters to achieve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Squashed in build fix from Stephen:
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit allows injecting a board/platform/device-specific post-
processing function into the FIT image data loading process, which can
include modifying the size and altering the starting source address of
an image data artifact. This might be desired to do things like strip
headers or footers attached to the images before they were packaged into
the FIT, or to perform operations such as decryption or authentication.
Introduce new configuration option CONFIG_FIT_IMAGE_POST_PROCESS to
allow controlling this feature. If enabled, a platform-specific post-
process function must be provided.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The devicetrees for various platforms already exceed 16k. Add a define
CONFIG_SYS_FDT_SIZE to specify the FDT size, and set to 16k for the
two boards that define this CONFIG_SYS_FDT_BASE parameter. This
allows platforms with larger devicetree blobs to boot from NOR.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Add new Kconfig option to disable arch_fixup_fdt() calls for cases where
U-Boot shouldn't update memory setup in DTB file.
One example of usage of this option is to boot OS with different memory
setup than U-Boot use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix up the call in mmc_load_image_raw_partition() to use the correct
function to obtain the MMC device, so that this code can support driver
model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This change introduces default_splash_locations which
simplifies splash recovery from the first partition of
USB/MMC/SATA drive.
Given usual mapping of the first partition of external media for
basic boot stuff like uImage/zImage, .dtb etc it looks quite
obvious option to put there splash.bmp as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Current implementation of splash_init_usb() requires usb_stor_scan()
which doesn't exist in case of DM_USB simply because real probing
happens right in usb_init().
So disable usage of usb_stor_scan() in case of DM_USB.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Robert Winkler <robert.winkler@boundarydevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In certain circumstances it comes in handy to be able to boot into a second
U-Boot. But as of now it is not possible to boot a U-Boot binary that is inside
a FIT image, which is problematic for projects that e.g. need to guarantee a
unbroken chain of trust from SOC all the way into the OS, since the FIT signing
mechanism cannot be used.
This patch adds the capability to load such FIT images.
An example .its snippet (utilizing signature verification) might look
like the following:
images {
firmware@1 {
description = "2nd stage U-Boot image";
data = /incbin/("u-boot-dtb.img.gz");
type = "firmware";
arch = "arm";
os = "u-boot";
compression = "gzip";
load = <0x8FFFC0>;
entry = <0x900000>;
signature@1 {
algo = "sha256,rsa4096";
key-name-hint = "key";
};
};
};
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
In raw mode a full sector is to be read even if image covers part of
a sector. Number of sectors are calculated as ROUND_UP(size)/sec_size by FIT
framework. This calculation assumes that image is at the 0th offset of a sector,
which is not true always in FIT case. So, include the image offset while
calculating number of sectors.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Other payload than uImage is currently considered to be raw U-Boot
image. Check also for zImage in Falcon mode.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for loading from UBI volumes on the top of NAND
and OneNAND.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move config option CONFIG_SYS_NO_FLASH as Kconfig
option. All the boards which needs to enable this
option can be done through defconfigs
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Make code 64bit aware.
Warnings:
+../arch/arm/lib/spl.c: In function ‘jump_to_image_linux’:
+../arch/arm/lib/spl.c:63:3: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
+../common/spl/spl_fat.c: In function ‘spl_load_image_fat’:
+../common/spl/spl_fat.c:91:33: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When secure ram is used, MMU tables have to be put into secure ram.
To use common MMU code, gd->arch.tlb_addr will be used to host TLB
entry pointer. To save allocated memory for later use, tlb_allocated
variable is added to global data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When CONFIG_OF_PLATDATA is enabled, we cannot use the u-boot,dm-pre-reloc
device tree property since the device tree is not available. However,
dt-platdata.c only includes devices which would have been present in the
device tree, and we can assume that all such devices are needed for SPL.
If they were not needed, they would have been omitted to save space.
So in this case, bind all devices regardless of the u-boot,dm-pre-reloc
setting. This avoids needing to add a DM_FLAG_PRE_RELOC to every driver,
thus affecting U-Boot proper also.
Signed-off-by: Simon Glass <sjg@chromium.org>
The function fixup_silent_linux() is called in status BOOTM_STATE_LOADOS
to silence Linux if variable 'silent' is set.
Currently only the 'bootm' command state machine contains
BOOTM_STATE_LOADOS, but others like 'booti' or 'bootz' commands do not.
This means silent Linux does not work with these commands.
This patch moves the fixup_silent_linux() call out of the
BOOTM_STATE_LOADOS state and into BOOTM_STATE_OS_PREP, to silence Linux
independently of the used command (booti, bootm or bootz).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
At present sandbox exits when the 'bootm' command completes, since it is not
actually able to run the OS that is loaded. Normally 'bootm' failure is
considered a fatal error in U-Boot.
However this is annoying for tests, which may want to examine the state
after a test is complete. In any case there is a 'reset' command which can
be used to exit, if required.
Change the behaviour to return normally from the 'bootm' command on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Teddy Reed <teddy.reed@gmail.com>
Add generic functions which can look up information about a category:
- the number of items in the category
- the category description
- an item long time
- an item short time
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present the name is NULL, which prevents qsort() fromp being used. Use
the name "invalid" instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a table that contains the category name, the number of items in each
category and a pointer to the table of items. This will allow us to use
generic code to deal with the categories.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The next stage boot loader image and the selected FDT can be post-
processed by board/platform/device-specific code, which can include
modifying the size and altering the starting source address before
copying these binary blobs to their final destination. This might be
desired to do things like strip headers or footers attached to the
images before they were packaged into the FIT, or to perform operations
such as decryption or authentication. Introduce new configuration
option CONFIG_SPL_FIT_IMAGE_POST_PROCESS to allow controlling this
feature. If enabled, a platform-specific post-process function must
be provided.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes the following compiler error:
common/fb_mmc.c: In function ‘fb_mmc_erase’:
common/fb_mmc.c:209:17: error: ‘struct blk_desc’ has no member named
‘block_erase’
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_*, instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Move the bootdelay >= 0 check to the caller, which simplifies
the callees.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Factor out the same code from the callees to the caller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Because abortboot_keyed() and abortboot_normal() are not compiled
at the same time, we can rename both of them to __abortboot().
This allows to drop #ifdef from the caller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.
To sum up, the autoboot behaves as follows:
[1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
autoboot with no delay, with no check for abort
[3] CONFIG_BOOTDELAY=-1
disable autoboot
[4] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the
cases only by CONFIG_BOOTDELAY, like this:
[1] CONFIG_BOOTDELAY=0
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=-1
disable autoboot
[3] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
This commit converts the logic as follow:
CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
--> CONFIG_BOOTDELAY=-2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
The same information now exists in common/Kconfig. Do not duplicate
documentation from the point of view of maintainability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add CONFIG_{SD|NAND|ONENAND|SPI|QSPI|SATA}_BOOT kconfig entries.
SoCs supports loading U-Boot from different medias to DRAM, such as
i.MX6/7 supports loading U-Boot to DRAM from sd/emmc/nand/qspi/spi/sata
and etc. For i.MX, imximage will generate different IVT headers according
to boot medias.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>
Not only am335x supports booting from NOR, i.MX6 SoCs also
supports booting from NOR. Make NOR_BOOT a common
option to let different SoCs share it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- increase the size of the fill buffer
- testing has shown a 10x improvement when the sparse image
has large CHUNK_TYPE_FILL chunks
Signed-off-by: Steve Rae <srae@broadcom.com>
In order to process the CHUNK_TYPE_DONT_CARE properly, there is
a requirement to be able to 'reserve' a specified number of blocks
in the storage media. Because of the special handling of "bad blocks"
in NAND devices, this is implemented in a storage abstraction function.
Signed-off-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- update fastboot_okay() and fastboot_fail()
This file originally came from upstream code.
While retaining the storage abstraction feature, this is the second
set of the changes required to resync with the
cmd_flash_mmc_sparse_img()
in the file
aboot.c
from
https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1
Signed-off-by: Steve Rae <srae@broadcom.com>
This "session-id" alogrithm is not required, and currently corrupts
the stored image whenever more the one "session" is required.
Signed-off-by: Steve Rae <srae@broadcom.com>
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
There is no more define of CONFIG_SYS_HUSH_PARSER. Rename some
remaining references and drop the backward compatible Kconfig entry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We already support iminfo for other images. The idea
of this patch is start to have a minimal support for
android image format. We still need to print id[] array
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit bb597c0eeb ("common: bootdelay: move CONFIG_BOOTDELAY
into a Kconfig option"), CONFIG_BOOTDELAY is defined for all boards.
Prior to that commit, it was allowed to unset CONFIG_BOOTDELAY to
not compile common/autoboot.c, as described in common/Makefile:
# This option is not just y/n - it can have a numeric value
ifdef CONFIG_BOOTDELAY
obj-y += autoboot.o
endif
It was a bit odd to enable/disable code with an integer type option,
but it was how this option worked before that commit, and several
boards actually unset it to opt out of the autoboot feature.
This commit adds a new bool option, CONFIG_AUTOBOOT, and makes
CONFIG_BOOTDELAY depend on it.
I chose "default y" for this option because most boards use the
autoboot. I added "# CONFIG_AUTOBOOT is not set" for the boards that
had not set CONFIG_BOOTDELAY prior to the bad commit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Somehow this got overlooked when getting rid of nand_info.
Small patch, won't affect anything else, no reason to wait for the
next cycle.
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
On modern NAND it's more than recommended to have a backup copy of the
u-boot binary to recover from corruption: bitflips are quite common on
MLC NANDs, and the read-disturbance will corrupt your u-boot partitition
more quickly than what you would see on an SLC NAND.
Add an extra Kconfig option to specify the offset of the redundant u-boot
image.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[scottwood: added ifdef to fix build break]
Signed-off-by: Scott Wood <oss@buserror.net>
Correct the error message in spl_load_image_ext() when image parsing
fails. Instead of "ext4fs_read failed" print "failed to parse image
header".
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Guillaume GARDET <guillaume.gardet@free.fr>
CC: Tom Rini <trini@konsulko.com>
Remove redundant #if defined(CONFIG_SPL_OS_BOOT) statement around
getenv() calls in spl_load_image_ext_os().
The whole function is surrounded by #ifdef CONFIG_SPL_OS_BOOT.
No functional change.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Guillaume GARDET <guillaume.gardet@free.fr>
Acked-by: Guillaume GARDET <guillaume.gardet@free.fr>
The comments in the source file are riddled with spelling mistakes. Be
a good citizen and take a stab at cleaning up some of the more obvious
ones.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case we have restarted u-boot there is a chance that environment
buffer contains old environment (from the previous boot). If UBI volume
is zero size, ubi_volume_read() doesn't modify the buffer and exits
successfully.
We need to clear buffer manually before reading it from UBI, so the
invalid CRC will cause setting default environment in case that the UBI
volume is zero size.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Flushing part of the cache should be done on cache boundaries. Trying to
flush part of a cache line is not supported and the request may be ignored
or print warnings.
Adjust the bootm code to align the end address to prevent this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This allows a board to configure verified boot within the SPL using
a FIT or FIT with external data. It also allows the SPL to perform
signature verification without needing relocation.
The board configuration will need to add the following feature defines:
CONFIG_SPL_CRYPTO_SUPPORT
CONFIG_SPL_HASH_SUPPORT
CONFIG_SPL_SHA256
In this example, SHA256 is the only selected hashing algorithm.
And the following booleans:
CONFIG_SPL=y
CONFIG_SPL_DM=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_FIT=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_SPL_OF_LIBFDT=y
CONFIG_SPL_FIT_SIGNATURE=y
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Sumit Garg <sumit.garg@nxp.com>
move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Fixes:
=> ext2ls scsi 0:1
** Bad device scsi 0:1 **
for boards which use the scsi legacy driver (such as ls1043ardb).
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Setup flag when default environment are used to be able to
rewrite default distro boot variables based on SoC boot mode.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
When no DTB can be matched successfully to the board that's being used
a list of available FIT-embedded DTBs will be output to the console for
diagnostic purposes. But rather than the contents of the "description"
FDT property a non-existent property was accessed and as a result "NULL"
was output instead of the actual name(s) of the DTB(s). Fix this issue
by using the correct property which is also the exact same property
that's used earlier during the actual board matching process.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Allow configuring the begining of the malloc_f area in SPL.
This patch uses the same CONFIG_MALLOC_F_ADDR established by
the sandbox.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Remove the check for GD_FLG_SPL_INIT in spl_relocate_stack_gd().
The check will always fail. This is because spl_relocate_stack_gd()
is called from ARM's crt0.S and it is called before board_init_r().
The board_init_r() calls spl_init(), which sets the GD_FLG_SPL_INIT
flag.
Note that reserving the malloc area in RAM is not a problem even
if the GD_FLG_SPL_INIT flag is not set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
When loading fit header, it should be loaded to a previous address
aligned to ARCH_DMA_MINALIGN and not 8. Fixing the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
This provides a way to load a FIT containing U-Boot and a selection of device
tree files from UART.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Detect a FIT when loading from NAND and handle it using the
new FIT SPL support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Make sure we continue to use (void *)(unsigned long) for
load_addr].
Signed-off-by: Tom Rini <trini@konsulko.com>
Detect a FIT when loading from a FAT File system and handle it using the
new FIT SPL support.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This provides a way to load a FIT containing U-Boot and a selection of device
tree files from a File system. Making sure that all the reads and writes
are aligned to their respective needs.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Make this still apply with Michal's alignment change for 'fit']
Signed-off-by: Tom Rini <trini@konsulko.com>
sectors field is not being updated when reading fdt from fit image. Because of
this size_of(u-boot.bin) is being read when reading fdt. Fixing it by updating
the sectors field properly.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This option is always enabled and is about to be removed. Drop references
to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Allow this to be unset, such that gd->mon_len is invalid. This seems to be
what the sh architecture does.
Signed-off-by: Simon Glass <sjg@chromium.org>
If bl_len is not aligned it can caused a problem because another code
expects that start is aligned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
