Introduce USB Gadget config option. This allows to combine Makefile
entries for SPL_USBETH_SUPPORT and SPL_DFU_SUPPORT.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Ravi Babu <ravibabu@ti.com>
The DFU Kconfig menu entries should be part of the SPL
Kconfig file. Also avoid using the top level Makefile by
moving the config dependent build artifacts to the driver/
and driver/usb/gadget/ Makfiles.
With that, DFU can be built again in SPL if
CONFIG_SPL_DFU_SUPPORT is enabled.
Fixes: 6ad6102246 ("usb:gadget: Disallow DFU in SPL for now")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Some devices (e.g. dra7xx) support loading to RAM using DFU without
having direct boot from RAM support. Make sure the linker list
does not contain BOOT_DEVICE_RAM if CONFIG_SPL_RAM_DEVICE is not
enabled.
Fixes: 98136b2f26 ("spl: Convert spl_ram_load_image() to use linker list")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
This fixes the loop delay when using a hw watchdog.
In case a watchdog is used that accesses CPU registers,
the defined delay of 20us in a tight loop will cause a
huge delay in the actual timeout seen. This is caused
by the fact that udelay will inheritantly call WATCHDOG_RESET.
Together with the omap wdt implementation, the seen timeout increases up to
around 30s. This makes the loop very slow and causes long
delays when using the modem.
Instead, implement the 2 sec loop by using the timer interface to know
when to break out of the timeout loop. Watchdog kicking is taken care of
by getc().
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Commit d97dc8a0 separated the non-command code into its own file
which caused variable sata_curr_device can not be set to a correct
value.
Before commit d97dc8a0, variable sata_curr_device can be set
correctly in sata_initialize().
After commit d97dc8a0, sata_initialize() is moved out to its own file.
Accordingly, variable sata_curr_device is removed from sata_initialize()
too. This caused sata_curr_device never gets a chance to be set properly
which prevent other commands from being executed.
This patch sets variable sata_curr_device properly.
Fixes: d97dc8a0 (dm: sata: Separate the non-command code into its
own file)
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make show_board_info() a weak function which allows for custom board
specific implementations thereof.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Drop CONFIG_CUSTOM_BOARDINFO as it is not Kconfig compliant and anyway
not really used anywhere plus the upcoming weak show_board_info()
approach seems much superior.
This reverts commit a9ad18c9d5.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Add check for FDT_MAGIC, otherwise also legacy images will be loaded as
a FIT. With this check in place, the loader works correct both
with legacy and FIT images.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current code assumes that the devices are ordered corresponding to
their alias value. But (for example) video1 can come before video0 in the
device tree.
Correct this, by always looking for device 0 first. After that we can fall
back to finding the first available device.
Signed-off-by: Simon Glass <sjg@chromium.org>
While we move some config macros to Kconfig, kconfig header is needed
to avoid compiling error if not already included.
Signed-off-by: York Sun <york.sun@nxp.com>
Commit ec6617c3 includes autoconf.h in image-fit.c, causing conflict
for board odroid-xu3 which overwrites CONFIG_SYS_BOARD in header
file. Move the include higher and use linux/kconfig.h instead of
generated/autoconf.h.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.
The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.
Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the need to explicitly add SHA/RSA pairings. Invalid SHA/RSA
pairings will still fail on verify operations when the hash length is
longer than the key length.
Follow the same naming scheme "checksum,crytpo" without explicitly
defining the string.
Indirectly adds support for "sha1,rsa4096" signing/verification.
Signed-off-by: Andrew Duda <aduda@meraki.com>
Signed-off-by: aduda <aduda@meraki.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cut down on the repetition of algorithm information by defining separate
checksum and crypto structs. image_sig_algos are now simply pairs of
unique checksum and crypto algos.
Signed-off-by: Andrew Duda <aduda@meraki.com>
Signed-off-by: aduda <aduda@meraki.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Padding verification was done against static SHA/RSA pair arrays which
take up a lot of static memory, are mostly 0xff, and cannot be reused
for additional SHA/RSA pairings. The padding can be easily computed
according to PKCS#1v2.1 as:
EM = 0x00 || 0x01 || PS || 0x00 || T
where PS is (emLen - tLen - 3) octets of 0xff and T is DER encoding
of the hash.
Store DER prefix in checksum_algo and create rsa_verify_padding
function to handle verification of a message for any SHA/RSA pairing.
Signed-off-by: Andrew Duda <aduda@meraki.com>
Signed-off-by: aduda <aduda@meraki.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support was already implemented, but not hooked up. This fixes several
fails in the test cases.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Coverity complains that this can overflow. If we later increase the size
of one of the strings in the table, it could happen.
Adjust the code to protect against this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 150964)
- Add DEFAULT_FDT_FILE kconfig entry
- Move CONFIG_DEFAULT_FDT_FILE from include/configs to defconfigs
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This converts the following to Kconfig:
CONFIG_SYS_STDIO_DEREGISTER
This option should never be enabled in SPL, so use
CONFIG_IS_ENABLED(SYS_STDIO_DEREGISTER) when checking the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_ENV_OVERWRITE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
CONFIG_CONSOLE_MUX
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these option to Kconfig and tidy up existing uses.
The Power PC boards don't have a suitable common element: the common header
files don't appear to line up with the Kconfig files as far as I can tell.
This results in a lot of defconfig changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
[trini: Re-migrate, update common/console.c logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Hardware: CM-FX6 Module from Compulab
This patch fixes unwanted watchdog resets while the user enters
a command at the U-Boot prompt.
As found on the CM-FX6 board from Compulab, when having enabled the
watchdog, a missing WATCHDOG_RESET call in common/console.c causes
this and alike boards to reset when the watchdog's timeout has
elapsed while waiting at the U-Boot prompt.
Despite the user could press several keys within the watchdog
timeout limit, the while loop in cli_readline.c, line 261, does only
call WATCHDOG_RESET if first == 1, which gets set to 0 in the 1st
loop iteration. This leads to a watchdog timeout no matter if the
user presses keys or not.
Although, this affects other boards as well as it touches
common/console.c, the macro WATCHDOG_RESET expands to {} if watchdog
support isn't configured. Hence, there's no harm caused and no need to
surround it by #ifdef in this case.
* Symptom:
U-Boot resets after watchdog times out when in commandline prompt
and watchdog is enabled.
* Reasoning:
When U-Boot shows the commandline prompt, the following function
call stack is executed while waiting for a keypress:
common/main.c:
main_loop => common/cli.c: cli_loop() =>
common/cli_hush.c:
parse_file_outer => parse_stream_outer =>
parse_stream => b_getch(i) =>
i->get(i) => file_get =>
get_user_input => cmdedit_read_input =>
uboot_cli_readline =>
common/cli_readline.c:
cli_readline => cli_readline_into_buffer =>
cread_line => getcmd_getch (== getc) =>
common/console.c:
fgetc => console_tstc
common/console.c:
(with CONFIG_CONSOLE_MUX is set)
- in console_tstc line 181:
If dev->tstc(dev) returns 0, the global tstcdev variable doesn't get
set. This is the case if no character is in the serial buffer.
- in fgetc(int file), line 297:
Program flow keeps looping because tstcdev does not get set.
Therefore WATCHDOG_RESET is not called, as mx_serial_tstc from
drivers/serial/serial_mxc.c does not call it.
* Solution:
Add WATCHDOG_RESET into the loop of console_tstc.
Note: Macro expands to {} if not configured, so no #ifdef is needed.
* Comment:
Signed-off-by: Christian Storm <christian.storm@tngtech.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andreas J. Reichel <Andreas.Reichel@tngtech.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move SYS_OS_BASE to Kconfig and cleanup existing
uses.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Also migrate a4m2k]
Signed-off-by: Tom Rini <trini@konsulko.com>
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>
Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes devicetree nodes and or properties are added out of the u-boot
console, maybe through some script or manual interaction.
The devicetree as loaded or embedded is quite small, so the devicetree
has to be resized to take up those new nodes/properties.
In original the devicetree was only extended by effective
4 * add_mem_rsv.
With this commit we can add an argument to the "fdt resize" command,
which takes the extrasize to be added.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Simon Glass <sjg@chromium.org>
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is already called earlier, from fdtdec_setup(), so drop this unnecessary
call from the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present all video devices are probed on start-up. It would be better to
probe a device only when it is needed. This can happen if it is referenced
in the stdout environment variable, for example.
Add support for this by searching for a suitable device when needed, probing
it, and finding the stdio device it creates.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
By default saveenv option is not supported for SPL. This patch
enable the support for save environment variable for SPL build.
Enable save environment support in SPL after setenv. By default
the saveenv option is not provided in SPL, but some boards need
this support in 'Falcon' boot, where SPL need to boot from
different images based on environment variable set by OS. For
example OS may set "reboot_image" environment variable to
"recovery" inorder to boot recovery image by SPL. The SPL read
"reboot_image" and act accordingly and change the reboot_image
to default mode using setenv and save the environemnt.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Simon Glass <sig@chromium.org>
change in v1:
- dropped SUPPORT, use CONFIG_SPL_SAVEENV
- updates the comments in mmc_private.h
When CONFIG_SILENT_CONSOLE is defined and the default environment has
silent=1 it is not possible for a user to make the console un-silent if
the environment is not available when console_init_f() is called (for
example because the environment is in SPI).
Add a new helper function console_update_silent() and call it from both
console_init_f() and console_init_r().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no need for this to be in the BSS region. By moving it we can delay
use of BSS in SPL. This is useful for machines where the BSS region is not
in writeable space. On 64-bit x86, SPL runs from SPI flash and it is easier
to eliminate BSS use than link SPL to run with BSS at a particular
cache-as-RAM (CAR) address.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the fat loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the ext loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than having a global variable, pass the spl_image as a parameter.
This avoids BSS use, and makes it clearer what the function is actually
doing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Update existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. We need two variants - one for BOOT_DEVICE_CPGMAC and one for
BOOT_DEVICE_USBETH.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Also set up the sunxi function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All the other SPL loaders are in this directory, so move the SPI one in
there too.
There are two board-specific SPI loaders (fsl and sunxi). These remain in
the drivers/mtd/spi directory, since they do not contain generic code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Include updating the DFU case]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a linker list macro which can be used to declare an SPL image loader.
Update spl_load_image() to search available loaders for the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and tidy up existing uses. Also add a function
comment to the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than act on the global variable, pass the required struct in as a
parameter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This format can be flashed directly at address 0 of
the NAND FLASH, as it contains all necessary headers.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Move FASTBOOT_MBR_NAME and FASTBOOT_GPT_NAME into Kconfig.
Add dependency on the FASTBOOT_FLASH setting (also for FASTBOOT_MBR_NAME).
Remove the now redundant GPT_ENTRY_NAME.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add FIXME about xxx_PARTITION needing to be in Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add special target "mbr" (otherwise configurable via CONFIG_FASTBOOT_MBR_NAME)
to write MBR partition table.
Partitions are now searched using the generic function which finds any
partiiton by name. For MBR the partition names hda1, sda1, etc. are used.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far partition search by name has been supported only on the EFI partition
table. This patch extends the search to all partition tables.
Rename part_get_info_efi_by_name() to part_get_info_by_name(), move it from
part_efi.c into part.c and make it a generic function which traverses all part
drivers and searches all partitions (in the order given by the linked list).
For this a new variable struct part_driver.max_entries is added, which limits
the number of partitions searched. For EFI this was GPT_ENTRY_NUMBERS.
Similarly the limit is defined for DOS, ISO, MAC and AMIGA partition tables.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
This bug appears in b6396403 which makes u-boot unable to pass
arguments via bootm to a standalone application without this patch.
Steps to reproduce.
Compile a u-boot. Use mkimage to package the standalone hello_world.bin
file.
e.g. For the MIPS Boston platform
mkimage -n "hello" -A mips -O u-boot -C none -T standalone \
-a 0xffffffff80200000 -d hello_world.bin \
-ep 0xffffffff80200000 hello_out
Then tftp hello_out and run it using
boston # dhcp 192.168.154.45:hello_out
...
boston # bootm $loadaddr 123 321
Without the patch the following output is observed.
boston # bootm $loadaddr 123 321
Image Name: hello
Image Type: MIPS U-Boot Standalone Program (uncompressed)
Data Size: 1240 Bytes = 1.2 KiB
Load Address: 80200000
Entry Point: 80200000
Verifying Checksum ... OK
Loading Standalone Program ... OK
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 0
argv[0] = "0xffffffff88000000"
With the patch, you see the following.
boston # bootm $loadaddr 123 321
Image Name: hello
Image Type: MIPS U-Boot Standalone Program (uncompressed)
Data Size: 1240 Bytes = 1.2 KiB
Load Address: 80200000
Entry Point: 80200000
Verifying Checksum ... OK
Loading Standalone Program ... OK
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 3
argv[0] = "0xffffffff88000000"
argv[1] = "123"
argv[2] = "321"
argv[3] = "<NULL>"
Without the patch, the go command at the entry point seems to work.
boston # go 0xffffffff80200000 123 321
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 3
argv[0] = "0xffffffff80200000"
argv[1] = "123"
argv[2] = "321"
argv[3] = "<NULL>"
Hit any key to exit ...
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Without this, if g_dnl_register() fails, DFU code continues on
blindly and crashes. This fix makes it simply print an error
message instead.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
[l.majewski@samsung.com - some manual tweaks needed]
The cmd_dfu functionality is been used by both SPL and
u-boot, saperating the core dfu functionality moving
it to common/dfu.c.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Traditionally the DFU support is available only
as part 2nd stage boot loader(u-boot) and DFU
is not supported in SPL.
The SPL-DFU feature is useful for boards which
does not have MMC/SD, ethernet boot mechanism
to boot the board and only has USB inteface.
This patch add DFU support in SPL with RAM
memory device support to load and execute u-boot.
And then leverage full functionality DFU in
u-boot to flash boot inital binary images to
factory or bare-metal boards to memory devices
like SPI, eMMC, MMC/SD card using USB interface.
This SPL-DFU support can be enabled through
Menuconfig->Boot Images->Enable SPL-DFU support
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit bac17b78da ("image-fit: switch ENOLINK to ENOENT") changed
fit_get_node_from_config to return -ENOENT when a property doesn't
exist, but didn't change any of its callers which check return values.
Notably it didn't change boot_get_ramdisk, which leads to U-Boot failing
to boot FIT images which don't include ramdisks with the following
message:
Ramdisk image is corrupt or invalid
It also didn't take into account that by returning -ENOENT to denote the
lack of a property we lost the ability to determine from the return
value of fit_get_node_from_config whether it was the property or the
configuration node that was missing, which may potentially lead callers
to accept invalid FIT images.
Fix this by having fit_get_node_from_config return -EINVAL when the
configuration node isn't found and -ENOENT when the property isn't
found, which seems to make semantic sense. Callers that previously
checked for -ENOLINK are adjusted to check for -ENOENT, which fixes the
breakage introduced by commit bac17b78da ("image-fit: switch ENOLINK
to ENOENT").
The only other user of the return fit_get_node_from_config return value,
indirectly, is bootm_find_os which already checked for -ENOENT. From a
read-through of the code I suspect it ought to have been checking for
-ENOLINK prior to bac17b78da ("image-fit: switch ENOLINK to ENOENT")
anyway, which would make it right after this patch, but this would be
good to get verified by someone who knows this x86 code or is able to
test it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jonathan Gray <jsg@jsg.id.au>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Currently we have a mismash of architectures which use arch_cpu_init
from architecture-wide code (arc, avr32, blackfin, mips, nios2, xtensa)
and architectures which use arch_cpu_init from machine/SoC level code
(arm, x86).
In order to clean this mess up & allow for both use cases, introduce a
new mach_cpu_init callback which is run immediately after arch_cpu_init.
This will allow for architectures to have arch-wide code without needing
individual machines to all implement their own arch_cpu_init with a call
to some common function.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the config IDENT_STRING to Kconfig and migrate all boards
[sivadur: Migrate zynq boards]
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[trini: Update configs, add some default to sunxi Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some of the SPL options have TPL equivalents. Add these to Kconfig so that
we can convert these options over to work from Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a lot of SPL options in U-Boot to enable various features and
drivers. Currently these do not use Kconfig. Add them to Kconfig along
with suitable help, and drop them from the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present TPL uses the same options as SPL support. In a few cases the board
config enables or disables the SPL options depending on whether
CONFIG_TPL_BUILD is defined.
With the move to Kconfig, options are determined for the whole build and
(without a hack like an #undef in a header file) cannot be controlled in this
way.
Create new TPL options for these and update users. This will allow Kconfig
conversion to proceed for these boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reworks spl_set_header_raw_uboot to allow having both os boot
(which comes with a valid header) and aborting when no valid header is
found (thus excluding raw u-boot.bin images).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 62afc60188 introduced fpga image load via
bootm but broke the OS check in fit_image_load().
This commit removes following compiler warning:
---8<---
In file included from tools/common/image-fit.c:1:
/Volumes/devel/u-boot/tools/../common/image-fit.c:1715:39: warning: use of logical '||' with constant operand [-Wconstant-logical-operand]
os_ok = image_type == IH_TYPE_FLATDT || IH_TYPE_FPGA ||
^ ~~~~~~~~~~~~
/Volumes/devel/u-boot/tools/../common/image-fit.c:1715:39: note: use '|' for a bitwise operation
os_ok = image_type == IH_TYPE_FLATDT || IH_TYPE_FPGA ||
^~
|
1 warning generated.
--->8---
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
When phy autoneg on, the link speed and duplex should be
determined by phy advertising register and
phy link partner ability register.
Check phy advertising register when geting phy link speed and
duplex if autoneg on.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This improves the cread_line() function so that it will correctly
process the 'Home', 'End', 'Delete' and arrow key escape sequences
produced by various terminal emulators. This makes command line editing
a more pleasant experience.
The previous code only supported the cursor keys and the 'Home' key, and
only for certain terminal emulator configurations. This adds support for
the 'End and 'Delete' keys, and recognises a wider range of escape
sequences. For example, the left arrow key can be 'ESC O D' instead of
'ESC [ D', and the 'Home' key can be 'ESC [ H', 'ESC O H', 'ESC 1 ~' or
'ESC 7 ~', depending on what terminal emulator you use and how it is
configured.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Changes for v2
- Explicitly initialize variable to avoid spurious compiler warning.
Changes for v3
- Remove unnecessary setting of 'act' to ESC_REJECT (now its default
value).
The bootz and booti commands rely on common functionality that is found
in common/bootm.c and common/bootm_os.c. They do not however rely on
the rest of cmd/bootm.c to be implemented so split them into their own
files. Have various Makefiles include the required infrastructure for
CONFIG_CMD_BOOT[IZ] as well as CONFIG_CMD_BOOTM. Move the declaration
of 'images' over to common/bootm.c.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that nand_info[] is an array of pointers we need to ensure that it's
been populated prior to use. We may for example have ENV in NAND set in
configurations that run on boards with and without NAND (where default
env is fine enough, such as omap3_beagle and beagleboard (NAND) vs
beagle xM (no NAND)).
Fixes: b616d9b0a7 ("nand: Embed mtd_info in struct nand_chip")
Cc: Scott Wood <oss@buserror.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Scott Wood <oss@buserror.net>
