Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the driver to support the device tree and the driver model.
Timings and panel parameters are now loaded from the device tree.
The DM code replaces the am335x_lcdpanel structure with
tilcdc_panel_info taken from the linux kernel, as well the management
of additional parameters not covered in the legacy code. In addition,
the am335x_lcdpanel structure contains parameters and operations that
were probably a requirement of the board for which this driver was
developed and which, however, were not developed in the linux kernel.
All this led to rewrite th DM controller initialization code, except
for the pixel clock setting that is executed in a function created in a
previous patch with code taken from the legacy am335xfb_init.
The patch has been tested on a custom board with u-boot 2018.11-rc2 and
the following device-tree configuration:
panel {
compatible = "ti,tilcdc,panel";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pins>;
enable-gpios = <&gpio0 31 0>;
backlight = <&backlight>;
status = "okay";
u-boot,dm-pre-reloc;
panel-info {
ac-bias = <255>;
ac-bias-intrpt = <0>;
dma-burst-sz = <16>;
bpp = <16>;
fdd = <0x80>;
sync-edge = <0>;
sync-ctrl = <1>;
raster-order = <0>;
fifo-th = <0>;
};
display-timings {
native-mode = <&timing0>;
timing0: 800x480 {
hactive = <800>;
vactive = <480>;
hback-porch = <46>;
hfront-porch = <210>;
hsync-len = <20>;
vback-porch = <23>;
vfront-porch = <22>;
vsync-len = <10>;
clock-frequency = <33000000>;
hsync-active = <0>;
vsync-active = <0>;
};
};
};
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- add BOARD_LATE_INIT function calls in board.c
- add swi_status detection in board.c
- mux: add guardian interfaces to single pinmux structure
- am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
The board_early_init_f() inits clock before initing pinmux. However,
the clock configuration code might need to adjust PMIC settings of a
PMIC on I2C bus (e.g. board/ti/am335x/board.c does that). If the I2C
bus pin muxing is not configured before attempting to communicate
with the PMIC, the communication will silently fail and the prcm_init()
may configure fast enough CPU clock that the default voltage provided
by the PMIC would be insufficient and the platform would become
unstable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Tom Rini <trini@konsulko.com>
for suspend/resume robustness
update value for ext_phy_ctrl_36 for suspend/resume robustness
with hardware leveling enabled.
Match recommended values from EMIF Tools app note:
http://www.ti.com/lit/an/sprac70/sprac70.pdf
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
In case of RTC+DDR resume, need to restore EMIF context
before initiating hardware leveling.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[j-keerthy@ti.com Fixed the am335x build issues]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Enable HW leveling in RTC+DDR path. The mandate is to enable
HW leveling bit and then wait for 1 ms before accessing any
register.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Adjust DQS skew in case where invert_clkout=1 is used.
Match recommended values from EMIF Tools app note:
http://www.ti.com/lit/an/sprac70/sprac70.pdf
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to
have an non-standard boot address in memory. This may be due
to the device being a high security variant, which place the
Initial SoftWare (ISW) after certificates and secure software.
Allow these devices to set this from Kconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
When DM_USB is used, either the USB controllers are bound when the DTB
is parsed (when OF_CONTROL is enabled) or they are bound using the
U_BOOT_DEVICES() macro.
In the later case, the platform data is passed in a struct ti_musb_platdata
because it cannot be read from the DTB.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no need for an embedded device tree for this board so let the
build process generate a separate u-boot.dtb file instead.
Signed-off-by: Felix Brack <fb@ltec.ch>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone
boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
In order to use DM_I2C, we need to move the board detection after the
early SPL initialization.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If DM_I2C is used , the I2C controllers must be registered as U_BOOT_DEVICE
because OF_CONTROL is not used in the SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This inhibits the re-inititialization of DDR during an RTC-only resume. If
this is not done, an L3 NOC error is produced as the DDR gets accessed
before the re-init has time to complete. Tested on AM437x GP EVM.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[j-keerthy@ti.com Ported to Latest Master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Prevent EMIF control of DDR_RESET line on DDR3 am43xx platforms for
am43xx_evm_rtconly_config. Without this DDR is unstable and can become
corrupted after multiple iterations of RTC+DDR mode.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[j-keerthy@ti.com Ported to latest master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With driver model enabled in SPL, sdram_init() requires device tree
and malloc to be initialized.
Therefore call spl_early_init() in early_system_init().
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
DPLL DRR doesn't have an M4 divider. But the clock driver is trying
to configure M4 divider as 4(writing into a reserved register).
Fixing it by making M4 divider as -1.
Reported-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch provides default implementations of the two functions
set_uart_mux_conf and set_mux_conf_regs. Hence boards not using
them do not need to provide their distinct empty definitions.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_SPL
Note that trats does not actually use SPL, so this option can no-longer be
set.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Similar to what is done with OMAP5 class boards we need to
perform fixups common to this SoC class, add support for this here
and add HS fixups.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The declaration of otg*_plat and otg*_board_data is guarded by
CONFIG_USB_MUSB_*, but their use in arch_misc_init is not. The
ifdef flow goes something like:
if (CONFIG_USB_MUSB_* && other_conditions)
declare usb_data
if (other_conditions)
use usb_data
Thus when CONFIG_USB_MUSB_* is not declared, we try to use the
data structures, but these structures aren't defined.
To fix this, move the USB initialization code into the same #ifdef
which guards the declaration of the data structures. Since the DM_USB
vs legacy cases are completely different, use two versions of
arch_misc_init(), for readability.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The TI816x has 2 GPIO banks. For bank 0 we had been clearing the enable
bit when setting BIT(8). Correct this by setting it to BIT(1) | BIT(8)
after we set and wait for BIT(1) (aka PRCM_MOD_EN). Enable GPIO1 as
well so that when CMD_GPIO is enabled it won't crash probing the second
bank. Enable CMD_GPIO on ti816x_evm.
Signed-off-by: Tom Rini <trini@konsulko.com>
ROM stores the boot params information in a known location
and passes it to SPL. This information needs to be copied
very early during boot or else there is a chance of getting
corrupted by SPL. So move this boot device detection very early
during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.
Details:
- Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
OMAP4/5), so we can obtain status register in common way
- For now ctrl structure for AM33xx/OMAP3 contains only status register
address
- Run hw_data_init() in order to assign ctrl to proper structure
- Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
(DEVICE_TYPE_MASK and GP_DEVICE are used instead)
- Guard structs in omap_common.h with #ifdefs, because otherwise
including omap_common.h on non-omap4/5 board files breaks compilation
Buildman script was run for all OMAP boards. Result output:
arm: (for 38/616 boards)
all +352.5
bss -1.4
data +3.5
rodata +300.0
spl/u-boot-spl:all +284.7
spl/u-boot-spl:data +2.2
spl/u-boot-spl:rodata +252.0
spl/u-boot-spl:text +30.5
text +50.4
(no errors to report)
Tested on AM57x EVM and BeagleBoard xM.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Almost all users of CONFIG_AM33XX/AM43XX have been migrated. Finish
moving the last few over to Kconfig, and put all of the boards under the
appropriate Kconfig chocie now. This board choice is non-optional, so
remove that keyword on am33xx.
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX. It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family. In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations. Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient. Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still. As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it. We also remove a bunch
of other untested code about changing the speed the DDR runs at.
Signed-off-by: Tom Rini <trini@konsulko.com>