The fdtdec_get_addr() does not take into account values set in #address-cells
and #size-cells , but assumes them to be 1 for 32bit systems and 2 for 64bit
systems. This is true for most DTs, however there are exceptions. Switch to
fdtdec_get_addr_size_auto_noparent(), which takes the #address/size-cells
values into consideration, otherwise the reset controller node register
offset is incorrectly parsed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on V2H Blanche.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
mmc bootbus and partconf commands are needed in order to be able to
configure booting from separate boot0/boot1 eMMC partitions.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
EFI was disabled in f95b8a4b5f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Sub-nodes of /reserved-memory may be disabled. In this case we should not
reserve memory in the memory map.
Reported-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Fixes: fef907b2e4 ("efi_loader: create reservations after
ft_board_setup")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
On 32 bit systems fix
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
Fixes: a415d61eac ("cmd: map addresses to sysmem in efidebug memmap")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With CONFIG_OF_CONTROL environment variable $fdtcontroladdr is not defined
and test_efi_helloworld_net() fails.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We need to align the cache buffer to ARCH_DMA_MINALIGN in order to avoid
access errors like
CACHE: Misaligned operation at range [be0231e0, be0235e0]
seen on the MCIMX7SABRE.
Fixes: d5aee659f2 ("fs: ext4: cache extent data")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Commit 41e30dcf87 ("cmd: mmc: Make Mode: printout consistent") fixed
the layout of `mmc info` output. Reflect this change in the respective
testcase.
Also fix a typo in the documentation.
Fixes: 41e30dcf87 ("cmd: mmc: Make Mode: printout consistent")
Signed-off-by: Harald Seiler <hws@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently this causes failures of the platform when running the EFI
loader tests, so disable it for now.
This reverts commit af827140e5.
Signed-off-by: Tom Rini <trini@konsulko.com>
Depending on the SoC, a header of four characters is prepended to the
image. There is already a macro defining the number of characters:
RK_SPL_HDR_SIZE, so use it instead of hardcoding "4".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 79030a4861 ("rockchip: Add Single boot image
(with binman, pad_cat)") the following boot regression is seen:
U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
initcall sequence 67fd12a0 failed at call 6000b927 (err=-22)
This happens because the above commit missed to include the
"rockchip-u-boot.dtsi" for rv1108, so include this file
like it done for other Rockchip SoC dtsi's.
Fixes: 79030a4861 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the following error message is seen during boot:
U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
APLL: 600000000 DPLL:1200000000 GPLL:1188000000
ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000
MMC: dwmmc@30110000: 0
Loading Environment from MMC... OK
In: serial@10210000
Out: serial@10210000
Err: serial@10210000
Model: Elgin RV1108 R1 board
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
....
Since the elgin-rv1108 does not use ADC to read the download
key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid
such error.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 8e9a8d0d0c ("rockchip: elgin-rv1108: use board_early_init_f
for per-boar init") the function that configure the board GPIOs is no
longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected.
These GPIOs do not need to be configured in such early stagem, so change it
to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y
to fix the regression.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to make the console pins more robust to noise, activate
the pullups and increase its drive strength.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These boards aren't ChromeOS devices so won't have a cros-ec-keyb
input as it's the keyboard available via the ChromeOS Embedded
Controller. Update them to use a USB keyboard which would actually
be available. Also enable the usb keyboard option for those devices
that don't have it enabled already.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use syscon API to get grf base instead of get from dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use syscon API to get grf base instead of get from dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
EFI was disabled in f95b8a4b5f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
This series contains bug fixes for the UEFI sub-system:
* report correct variable length in GetNextVariable()
* correct copying direction if freestanding memmove()
* remove const for parameter of GetNextVariableName()
* correct function descriptions
Unit tests are added and adjusted.
-----BEGIN PGP SIGNATURE-----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=+Nkf
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4 (5)
This series contains bug fixes for the UEFI sub-system:
* report correct variable length in GetNextVariable()
* correct copying direction if freestanding memmove()
* remove const for parameter of GetNextVariableName()
* correct function descriptions
Unit tests are added and adjusted.
'vendor' is both an input and an output parameter. So it cannot be
constant.
Fixes: 0bda81bfdc ("efi_loader: use const efi_guid_t * for variable services")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
For EFI binaries we have to provide an implementation of memmove() in
efi_freestanding.c.
Before this patch the memmove() function was copying in the wrong
direction.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
GetNextVariableName should report the length of the variable including the
final 0x0000 in bytes.
Check this in the unit test.
Increase the buffer size for variable names. 40 bytes is too short.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The runtime service GetNextVariable() returns the length of the next
variable including the closing 0x0000. This length should be in bytes.
Comparing the output of EDK2 and U-Boot shows that this is currently not
correctly implemented:
EDK2:
OsIndicationsSupported: 46
PlatformLang: 26
PlatformLangCodes: 36
U-Boot:
OsIndicationsSupported: 23
PlatformLang: 13
PlatformLangCodes: 18
Provide correct length in GetNextVariable().
Fixes: d99a87f84b ("efi_loader: implement GetNextVariableName()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.
Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some config symbols are found in *almost* every _defconfig file for
Allwinner boards, because those options are actually a platform choice,
and not a per-board decision.
Some of these options are older, some have recently been added.
Move those options to be set for all Allwinner boards in their
respective Kconfig files.
The rationales are as follows:
- NR_DRAM_BANKS: All Allwinner SoC map DRAM at one contiguous region of
address space only, starting at 1 GB. So it's always one bank.
- SPL_{DOS,EFI}_PARTITION: The Allwinner SPL does only support raw MMC
accesses, we don't care about filesystems or partitions in there, so
there is no need to define those symbols at all.
- USE_PREBOOT: We start USB early when a keyboard is configured, using the
preboot env variable, so we need to set this variable.
- SYS_RELOC_GD_ENV_ADDR: We don't specify any ENV_ADDR, so need this
symbol to be set (according to 8d8ee47e03).
- SYS_USB_EVENT_POLL_VIA_INT_QUEUE: According to commit eab9433aa5,
specifying this reduces the latency of the USB keyboard handling, so
this was formerly enabled in config headers for all Allwinner boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Pine H64 board comes with some onboard SPI flash chip, which is
perfect for loading SPL, ATF and U-Boot proper from there.
Enable the functionality in the defconfig, so that we use sunxi-fel to
transfer a bootable image to the NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC uses a quite different memory map, also changes the
clocks quite a bit. This requires some changes to the SPL SPI routine,
which hardcodes these values so far.
Using the just introduced helper functions to determine base address
and SPI controller generation, we can cover some of these differences
easily.
The clock setup is different, so requires some explicit code changes
there (reset and clock gate in one register at a different address).
Also we need to change the pinmux function to use a different set of
pins that the H6 uses for SPI0.
Eventually we can enable the H6 to use SPI booting in Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Now that we can easily select an SoC specific SPI0 base address, adding
support for the Allwinner R40 is fairly trivial:
We set the base address, add this SoC to the ones that use PC23 and
enable it in Kconfig.
This allows booting from SPI flash on R40 boards.
Tested on a Bananapi M2 Berry with SPI flash connected to the header pins.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
So far we were using the CONFIG_SUNXI_GEN_SUN6I symbol to select between
the two SPI controller generations used on Allwinner SoCs. This is a
convenience symbol to roughly differentiate between "older" and "newer"
generation of SoCs.
The H6 SoCs is the newest SoC so far, but is sufficiently different to
not define this symbol. However it is using a SPI controller compatible
to the "new gen" SoCs.
To prepare for H6 support, we replace the check for this single symbol
with an explicit function, which can later be extended.
For now we just return CONFIG_SUNXI_GEN_SUN6I in there, so this does not
create a functional change.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
So far on all supported Allwinner SoCs we find the old generation SPI
controller always at address 0x1c05000, and the new generation one at
0x1c68000. However the Allwinner R40 SoC has a new generation SPI at
the old address, and the H6 uses a completely different address.
So split off the base address from the respective SPI registers, by
changing the #defines to just contain offsets.
The base address is provided by a function, so it can easily be extended
later when support for those SoCs materialises.
This does not change the code size (since the toolchain is clever enough
to optimise this properly), also does not bring any functional change at
this point.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This series fixes several bugs:
* consider the /reserved-memory node in the device tree
* consider memory reservations created in ft_board_setup()
* correct output of 'efidebug memmap' on the sandbox
* correct the definition of efi_capsule_header()
Furthermore some definitions needed for future patches are added to
header files.
-----BEGIN PGP SIGNATURE-----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=zB6g
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc4-4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4 (4)
This series fixes several bugs:
* consider the /reserved-memory node in the device tree
* consider memory reservations created in ft_board_setup()
* correct output of 'efidebug memmap' on the sandbox
* correct the definition of efi_capsule_header()
Furthermore some definitions needed for future patches are added to
header files.
Using memcpy() for some MMIO access is generally frowned upon and might
break things on some platforms. Allwinner H3, which fails to boot, being
an example here.
Moreover, fields being accessed are naturally aligned and warnings
produced by GCC have been quiesced for some time already by:
53dc8ae ("gcc-9: silence 'address-of-packed-member' warning")
That said, it should be okay to revert this commit.
This reverts commit 9bd34a69a4.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
See UEFI specification, section 8.5.3.
In addition, the structure, efi_capsule_header, should be "packed"
as it is a serialized binary format in a capsule file.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This is a preparatory patch.
Those functions will be used in an implementation of UEFI firmware
management protocol as part of my capsule update patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Some of those values will be used in an implementation of UEFI firmware
management protocol as part of my capsule update patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
These flags are expected to be set in OsIndicationsSupported variable
if corresponding features are supported. See UEFI specification,
section 8.5.4.
In particular, capsule-related flags will be used in my capsule
update patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fix misspelled EFI_OS_INDICATIONS_BOOT_TO_FW_UI.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, bootefi only parses memory reservation block to setup
EFI reserved memory mappings. However, it doesn't parse the
reserved-memory[1] device tree node that also can contain the
reserved memory regions.
Add capability to parse reserved-memory node and update the EFI memory
mappings accordingly.
1. <U-Boot source>/doc/device-tree-bindings/reserved-memory/reserved-memory.txt]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Fix an endless loop.
The /reserved-memory node may have children without reg property. Remove
a superfluous debug statement.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
