Commit Graph

534 Commits

Author SHA1 Message Date
Heiko Schocher
001a831986 usb: dfu: introduce dfuMANIFEST state
on nand flash using ubi, after the download of the new image into
the flash, the "rest" of the nand sectors get erased while flushing
the medium. With current u-boot version dfu-util may show:

Starting download: [##################################################] finished!
state(7) = dfuMANIFEST, status(0) = No error condition is present
unable to read DFU status

as get_status is not answered while erasing sectors, if erasing
needs some time.

So do the following changes to prevent this:

- introduce dfuManifest state
  According to dfu specification
  ( http://www.usb.org/developers/devclass_docs/usbdfu10.pdf ) section 7:
  "the device enters the dfuMANIFEST-SYNC state and awaits the solicitation
   of the status report by the host. Upon receipt of the anticipated
   DFU_GETSTATUS, the device enters the dfuMANIFEST state, where it
   completes its reprogramming operations."

- when stepping into dfuManifest state, sending a PollTimeout
  DFU_MANIFEST_POLL_TIMEOUT in ms, to the host, so the host
  (dfu-util) waits the PollTimeout before sending a get_status again.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-23 02:20:09 +01:00
Gerhard Sittig
df4fb1c36d usb: net: introduce support for Moschip USB ethernet
introduce an 'mcs7830' driver for Moschip MCS7830 based (7730/7830/7832)
USB 2.0 Ethernet Devices

see "MCS7830 -- USB 2.0 to 10/100M Fast Ethernet Controller" at
http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=109;74;109

the driver was implemented based on the U-Boot Asix driver with
additional information gathered from the Moschip Linux driver,
development was done on "Delock 61147" and "Logilink UA0025C" dongles

Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2014-03-12 17:04:31 -04:00
Stephen Warren
eb838e7d84 usb: create common header virtual root hub descriptors
Many USB host controller drivers contain almost identical copies of the
same virtual root hub descriptors. Put these into a common file to avoid
duplication.

Note that there were some very minor differences between the descriptors
in the various files, such as:

- USB 1.0 vs. USB 1.1
- Manufacturer/Device ID
- Max packet size
- String content

I assume these aren't relevant.

Cc: Thomas Lange <thomas@corelatus.se>
Cc: Shinya Kuribayashi <skuribay@pobox.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Eric Millbrandt <emillbrandt@coldhaus.com>
Cc: Pierre Aubert <p.aubert@staubli.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Zhang Wei <wei.zhang@freescale.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Markus Klotzbuecher <mk@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: C Nauman <cnauman@diagraph.com>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Thomas Abraham <t-abraham@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Cc: Matej Frančeškin <matej.franceskin@comtrade.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-03-10 18:53:36 +01:00
Stephen Warren
8165e34bf4 usb: ehci: fully align interrupt QHs/QTDs
These data structures are passed to cache-flushing routines, and hence
must be conform to both the USB the cache-flusing alignment requirements.
That means aligning to USB_DMA_MINALIGN. This is important on systems
where cache lines are >32 bytes.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-03-10 18:53:36 +01:00
Stephen Warren
2456b97f0c ush: ehci: initialize altnext pointers in QH
Section 4.10.2 "Advance Queue" of ehci-specification-for-usb.pdf
specifies how an EHCI controller loads a new QTD for processing if the
QH is not already marked as active. It states:

=====
If the field Bytes to Transfer is not zero and the T-bit in the Alternate
Next qTD Pointer is set to zero, then the host controller uses the
Alternate Next qTD Pointer. Otherwise, the host controller uses the Next
qTD Pointer. If Next qTD Pointer’s T-bit is set to a one, then the host
controller exits this state and uses the horizontal pointer to the next
schedule data structure.
=====

Hence, we must ensure that the alternate next QTD pointer's T-bit
(TERMINATE) is set, so the EHCI controller knows to use the next QTD
pointer.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-03-10 18:53:36 +01:00
Stephen Warren
9a04a858eb net: asix: don't pad odd-length TX packets
For Ethernet/USB RX packets, the ASIX HW pads odd-sized packets so that
they have an even size. Currently, asix_recv() does remove this padding,
and asic_send() adds equivalent padding in the TX path. However, the HW
does not appear to need this packing for TX packets in practical testing
with "ASIX Elec. Corp. AX88x72A 000001" Vendor: 0x0b95 Product 0x7720
Version 0.1. The Linux kernel does no such padding for the TX path.

Remove the padding from the TX path:

* For consistency with the Linux kernel.
* NVIDIA has a Tegra simulator which validates that the length of USB
  packets sent to an ASIX device matches the packet length value inside
  the packet data. Having U-Boot and the kernel do the same thing when
  creating the TX packets simplifies the simulator's validation.

Cc: Lucas Stach <dev@lynxeye.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-03-07 10:59:06 -05:00
Alexey Brodkin
1ace402239 sizes.h - consolidate for all architectures
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 12:15:01 -05:00
Tom Rini
a7e8c15f71 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-25 13:55:49 -05:00
Nikhil Badola
91d7746df8 fsl/usb: Limit phy_type comparison to first four characters
Use first four characters for phy_type comparison. Strcmp() should not
be used to check the phy_type string which maybe parsed by hwconfig_subarg().
Hwconfig_subarg() returns part of hwconfig string starting from
phy_type value till the end of the string. Since phy_type could be
either "utmi" or "ulpi", strncmp() should be used so that a comparison
of "utmi;fsl_ddr:bank_intlv=auto" with "utmi" will succeed.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:57 -08:00
Tom Rini
6853e6aa77 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-20 12:18:59 -05:00
Tom Rini
130fbeb1c5 blackfin: Add <asm/clock.h> to numerous drivers
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.

Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-20 12:00:27 -05:00
Albert ARIBAUD
3e11350255 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
2014-02-20 13:16:05 +01:00
Masahiro Yamada
6825a95b0b kbuild: use Linux Kernel build scripts
Now we are ready to switch over to real Kbuild.

This commit disables temporary scripts:
  scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
  scripts/{Makefile.build,Makefile.host,Makefile.lib}.

This switch is triggered by the line in scripts/Kbuild.include
  -build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
  +build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj

We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.

Additionally, we need to fix compiler flags which are
locally added or removed.

In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-02-19 11:07:50 -05:00
Albert ARIBAUD
a87a0ce702 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2014-02-19 07:15:01 +01:00
Marek Vasut
f016f8ca3d usb: mv_udc: Rename to ci_udc
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-02-06 04:48:15 +01:00
Marek Vasut
b1c756782c ARM: USB: Remove the IXP EHCI driver
The driver is no longer used, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:52 +01:00
Lukasz Majewski
fc2d5d04e1 usb:gadget:f_thor: cosmetic: Remove debug memset
Apparently debug memset (with a 0x55 value) has been overlooked in the
f_thor code.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
84c13e6f61 usb:gadget:f_thor: Allocate request up to THOR_PACKET_SIZE not ep->maxpacket
Now it is possible to allocate static request - which receives data from
the host (OUT transaction) to the size of THOR packet.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
e0059eaef1 usb:udc:samsung: Zero copy approach for data passed to Samsung's UDC driver
The Samsung's UDC driver is not anymore copying data from USB requests to
aligned internal buffers. Now it works directly in data allocated in the
upper layers like UMS, DFU, THOR.

This change is possible since those gadgets now must take care to allocate
buffers aligned to cache line (CONFIG_SYS_CACHELINE_SIZE).

This can be achieved by using DEFINE_CACHE_ALIGN_BUFFER() or
ALLOC_CACHE_ALIGN_BUFFER() macros. Those take care to allocate buffer
aligned to cache line in both starting address and its size.
Sometimes it is enough to just use memalign() with size being a
multiplication of cache line size.

Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`

Measurement:
Transmission speed: 27.04 MiB/s

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
9c9822188c usb:udc:samsung: Allow burst transfers for non EP0 endpints
This patch removed obscure restriction on the HW setting of DMA transfers.
Before this change each transaction sent up to 512 bytes (with packet count
equal to 1) for non EP0 transfer.

Now it is possible to setup DMA transaction up to DMA_BUFFER_SIZE.

Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`

Measurement:
Transmission speed: 20.74 MiB/s

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
716662bd19 usb:udc:samsung: Remove redundant cache operation from Samsung UDC driver
A set of cache operations (both invalidation and flush) were redundant
in the S3C HS OTG Samsung driver:

1. s3c_udc_ep0_zlp - to transmit EP0's ZLP packets one don't need to flush
the cache (since it is the zero length transmission)

2. s3c_udc_pre_setup and s3c_ep0_complete_out - cache invalidation is not
needed when the buffer for OUT EP0 transmission is setup, since no data
has yet arrived.

Cache cleanups presented above don't contribute much to transmission speed
up, hence shall be regarded as cosmetic changes.

3. setdma_rx - here the s3c UDC driver's internal buffers were invalidated.
This call is not needed anymore since we reuse the buffers passed from
gadgets. This is a key contribution to transmission speed improvement.

Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`

Measurements:

Base values (without improvement):
Transmission speed: 9.51 MiB/s

After the change:
Transmission speed: 10.15 MiB/s

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:45 +01:00
Lukasz Majewski
16b7a29fc6 usb:gadget:ums: Replace malloc calls with memalign to fix cache buffer alignment
Calls to malloc() have been replaced by memalign. It now provides proper
buffer alignment.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2014-02-06 02:22:44 +01:00
Inderpal Singh
7da7651251 usb: exynos5: arndale: Add network support
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.

This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
2014-01-13 12:23:28 +01:00
Inderpal Singh
16f9480dfc usb: ehci: exynos: set/reset hsic phys
The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2
are for HSIC phys. The usb 2.0 phy is already being setup. This patch
sets up the hsic phys.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
2014-01-13 12:23:28 +01:00
Kuo-Jung Su
dcad280056 usb: gadget: fotg210: EP0 fifo empty indication is non-reliable
The fifo size of ep0 is 64 bytes, and if the packet size grater than
64 bytes, the driver would have to fill up the fifo multiple times,
and before filling up the fifo, the driver should make sure the fifo
is empty by checking fifo empty indication.

However there is a hardware bug that the fifo empty indication is
somehow a bit earlier than fifo reset. So if I don't add an extra
delay here, the data might be corrupted. (i.e., 1 byte missing)

After a couple of tests, it truns out that 1 usec is good enough.

This workaround should be applied to all hardware revisions.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2014-01-13 12:15:13 +01:00
Kuo-Jung Su
bd5e301d35 usb: gadget: fotg210: add w1c interrupt status support
Since hardware revision 1.11.0, the following interrupt status
registers are now W1C (i.e., write 1 clear):

1. Interrupt Source Group 0 Register (0x144) (EP0 Abort: BIT5)
2. Interrupt Source Group 2 Register (0x14C) (All bits)

And before revision 1.11.0, these registers are all R/W.
Which means software must write a 0 to clear the status.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2014-01-13 12:15:12 +01:00
Marek Vasut
eb63218b9b usb: ehci: Fix register access
Fix the register access in EHCI HCD. We need to use address of the register
as an ehci_writel() argument.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
2013-12-18 19:53:19 +01:00
Marek Vasut
1e1be6d478 usb: ehci: Do not de-init uninited controllers
In case the controller is not initialized, we shall not de-initialize it.
As the control structure will not be filled, we will produce a null ptr
dereference if the controller is not inited.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
2013-12-18 19:53:19 +01:00
Marek Vasut
8fb83547b9 usb: ehci-pci: Clarify and cleanup the EHCI controller detection
The detection function of the EHCI PCI controller was really cryptic,
add a beefy comment and clean the portion of the code up a bit. No
change in the logic of the code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
2013-12-18 19:53:19 +01:00
Lukasz Majewski
77b9504288 usb: f_dfu: cosmetic: Code cleanup
Code cleanup for dfu_bind_config function

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2013-12-18 19:53:19 +01:00
Lukasz Majewski
33fac4a6a2 usb: dfu: f_dfu: Provide infrastructure to adjust DFU's Poll Timeout value
It is necessary to deter the host from sending subsequent DFU_GETSTATUS
request in the case of e.g. writing the buffer to medium.

Here the timeout is increased when we fill up the whole buffer. This delay
allows eMMC memory to perform its internal operations.
Otherwise we end up with HOST's error regarding GET_STATUS receive timeout.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2013-12-18 19:53:19 +01:00
Masahiro Yamada
4f57a90cfa drivers/usb/gadget: select objects by obj-$(CONFIG-...)
Before switching to the real Kbuild, drivers/usb/gadget/Makefile
must be fixed.
If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE
is defined, both obj- and obj-y get empty.

We need non-empty obj- or obj-y on each Makefile
to generate built-in.o on the real Kbuild.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-12-13 09:18:44 -05:00
Albert ARIBAUD
375a4496ff Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-12-06 16:54:42 +01:00
Roger Quadros
835a5559bd usb: ehci-omap: Reset the USB Host OMAP module
In commit bb1f327 we removed the UHH reset to fix NFS root (over usb
ethernet) problems with Beagleboard (3530 ES1.0). However, this
seems to cause USB detection problems for Pandaboard, about (3/8).

On further investigation, it seems that doing the UHH reset is not
the cause of the original Beagleboard problem, but in the way the reset
was done.

This patch adds proper UHH RESET mechanism for OMAP3 and OMAP4/5 based
on the UHH_REVISION register. This should fix the Beagleboard NFS
problem as well as the Pandaboard USB detection problem.

Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-06 07:02:32 -05:00
Piotr Wilczek
4498cf252b driver:usb:s3c_udc: add support for Exynos4x12
This patch add new defines for usb phy for Exynos4x12.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-02 11:22:32 +09:00
Heiko Schocher
7a0d463f58 usb, g_dnl: make bcdDevice value configurable
add the possibility to set the bcdDevice number board specific.
Therefore the weak function g_dnl_get_board_bcd_device_number()
is introduced. Used on the siemens boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
2013-11-12 09:53:59 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Heiko Schocher
ec9002e4fa usb, g_dnl: make iSerialNumber board configurable
add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2013-11-08 20:46:20 +01:00
Mateusz Kulikowski
522c95647d usb: ohci-hcd: submit_common_msg: report actual_length properly
submit_common_msg should report amount of data passed from/to device.
Instead, it always returned size requested by Host.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
2013-11-08 20:46:19 +01:00
Przemyslaw Marczak
351e9b2069 usb: ums: add ums exit feature by ctrl+c or by detach usb cable
This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.

Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.

Changes v2:
- add a note to the README

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-11-08 20:46:19 +01:00
Przemyslaw Marczak
0697f206df usb: ums: fix disk capacity miscalculation and code cleanup
This patch prevents:
- ums disk capacity miscalculation because of integer overflow

Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
  initialization before gadget init
- Remove unnecessary code from mass storage driver

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2013-11-08 20:46:19 +01:00
Przemyslaw Marczak
93c813b3ac usb: ums: code refactoring to improve reusability on other boards.
This patch introduces some cleanups to ums code. Changes:

ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
  usb_mass_storage.h both default values as 0 if board config
  doesn't define them

common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h

cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string

Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
2013-11-08 20:46:19 +01:00
Bo Shen
dcd2f1a0d2 arm: atmel: get rid of too many ifdeffery
Get rid of too many ifdeffery in usb ohci driver

Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04 20:32:37 +01:00
Bo Shen
d9bef0ad2d arm: atmel: at91sam9n12ek: add usb host support
Add usb host support for at91sam9n12ek board.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04 20:32:35 +01:00
Masahiro Yamada
44e32c7144 drivers: usb: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 13:25:38 -04:00
ramneek mehresh
77354e9d50 powerpc/usb:Differentiate USB controller base address
Introduce different macros for storing addresses of multiple
USB controllers. This is required for successful initialization
and usage of multiple USB controllers inside u-boot

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2013-10-24 09:35:09 -07:00
Troy Kisky
7e575c46c3 usb: rename board_usb_init_type to usb_init_type
commit bba679144d
"usb: rename board_usb_init_type to usb_init_type" missed xhci-omap.c
So, fix that patch here, and fix a checkpatch warning.
WARNING: Avoid unnecessary line continuations

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-22 17:33:09 -04:00
Troy Kisky
449697f14e usb: udc: add udc.h include file
Move common definitions to udc.h
This allows musb_udc.h to be removed as well.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:38 +02:00
Troy Kisky
0f740cb8e4 usb: gadget: mv_udc: split mv_udc.h file
Move defines only needed by mv_udc.c to a file
in the same directory.

This allows usbtty to compile for mv_udc,
but it still doesn't link.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:36 +02:00
Troy Kisky
7b7924cdf8 usb: gadget: mv_udc: optimize ep_enable
Only get head if not ep0.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:33 +02:00