[ Upstream commit 39935dccb21c60f9bbf1bb72d22ab6fd14ae7705 ]
If a DDP broadcast packet is sent out to a non-gateway target, it is
also looped back. There is a potential for the loopback device to have a
longer hardware header length than the original target route's device,
which can result in the skb not being created with enough room for the
loopback device's hardware header. This patch fixes the issue by
determining that a loopback will be necessary prior to allocating the
skb, and if so, ensuring the skb has enough room.
This was discovered while testing a new driver that creates a LocalTalk
network interface (LTALK_HLEN = 1). It caused an skb_under_panic.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a28af7a3e85ddf358f8c41e401a33002f7a9587 ]
The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.
An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.
In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09078368d516918666a0122f2533dc73676d3d7e ]
ieee80211_find_sta_by_ifaddr() must be called under the RCU lock and
the resulting pointer is only valid under RCU lock as well.
Fix ath10k_wmi_tlv_op_pull_peer_stats_info() to hold RCU lock before it
calls ieee80211_find_sta_by_ifaddr() and release it when the resulting
pointer is no longer needed.
This problem was found while reviewing code to debug RCU warn from
ath10k_wmi_tlv_parse_peer_stats_info().
Link: https://lore.kernel.org/linux-wireless/7230c9e5-2632-b77e-c4f9-10eca557a5bb@linuxfoundation.org/
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210210212107.40373-1-skhan@linuxfoundation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e862a3e4088070de352fdafe9bd9e3ae0a95a33c ]
This ensure that previous association attempts do not leave stale statuses
on subsequent attempts.
This fixes the WARN_ON(!cr->bss)) from __cfg80211_connect_result() when
connecting to an AP after a previous connection failure (e.g. where EAP fails
due to incorrect psk but association succeeded). In some scenarios, indeed,
brcmf_is_linkup() was reporting a link up event too early due to stale
BRCMF_VIF_STATUS_ASSOC_SUCCESS bit, thus reporting to cfg80211 a connection
result with a zeroed bssid (vif->profile.bssid is still empty), causing the
WARN_ON due to the call to cfg80211_get_bss() with the empty bssid.
Signed-off-by: Luca Pesce <luca.pesce@vimar.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608807119-21785-1-git-send-email-luca.pesce@vimar.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e1caaf8ed22eb700cc47ec353816eee33186c1c ]
This patch fixes the max register value for the regmap.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-12-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e096a18867a5a989b510f6999d9c6b6622e8f7b ]
Since 20dd3850bc ("can: Speed up CAN frame receiption by using
ml_priv") the CAN framework uses per device specific data in the AF_CAN
protocol. For this purpose the struct net_device->ml_priv is used. Later
the ml_priv usage in CAN was extended for other users, one of them being
CAN_J1939.
Later in the kernel ml_priv was converted to an union, used by other
drivers. E.g. the tun driver started storing it's stats pointer.
Since tun devices can claim to be a CAN device, CAN specific protocols
will wrongly interpret this pointer, which will cause system crashes.
Mostly this issue is visible in the CAN_J1939 stack.
To fix this issue, we request a dedicated CAN pointer within the
net_device struct.
Reported-by: syzbot+5138c4dd15a0401bec7b@syzkaller.appspotmail.com
Fixes: 20dd3850bc ("can: Speed up CAN frame receiption by using ml_priv")
Fixes: ffd956eef6 ("can: introduce CAN midlayer private and allocate it automatically")
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Fixes: 497a5757ce4e ("tun: switch to net core provided statistics counters")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210223070127.4538-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e77f70e734584e0ad1038e459ed3fd2400f873a ]
This patch moves the CAN driver related infrastructure into a separate subdir.
It will be split into more files in the coming patches.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2126838050ccd1dadf310ffb78b2204f3b032b9 ]
the following command:
# tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \
$tcflags dst_ip 192.0.2.2 ip_ttl 63 action drop
doesn't drop all IPv4 packets that match the configured TTL / destination
address. In particular, if "fragment offset" or "more fragments" have non
zero value in the IPv4 header, setting of FLOW_DISSECTOR_KEY_IP is simply
ignored. Fix this dissecting IPv4 TTL and TOS before fragment info; while
at it, add a selftest for tc flower's match on 'ip_ttl' that verifies the
correct behavior.
Fixes: 518d8a2e9b ("net/flow_dissector: add support for dissection of misc ip header fields")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7867299cde34e9c2d2c676f2a384a9d5853b914d ]
The condition should be skipped if CPU ID equal to nthreads.
The patch doesn't fix any actual issue since
nthreads = min_t(unsigned int, num_present_cpus(), MVPP2_MAX_THREADS).
On all current Armada platforms, the number of CPU's is
less than MVPP2_MAX_THREADS.
Fixes: e531f76757 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dccdc5a1916d4266edd251f20bbbb113a5c495f ]
In ext4_rename(), when RENAME_WHITEOUT failed to add new entry into
directory, it ends up dropping new created whiteout inode under the
running transaction. After commit <9b88f9fb0d2> ("ext4: Do not iput inode
under running transaction"), we follow the assumptions that evict() does
not get called from a transaction context but in ext4_rename() it breaks
this suggestion. Although it's not a real problem, better to obey it, so
this patch add inode to orphan list and stop transaction before final
iput().
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210303131703.330415-2-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5de2055d31ea88fd9ae9709ac95c372a505a60fa ]
The use_ww_ctx flag is passed to mutex_optimistic_spin(), but the
function doesn't use it. The frequent use of the (use_ww_ctx && ww_ctx)
combination is repetitive.
In fact, ww_ctx should not be used at all if !use_ww_ctx. Simplify
ww_mutex code by dropping use_ww_ctx from mutex_optimistic_spin() an
clear ww_ctx if !use_ww_ctx. In this way, we can replace (use_ww_ctx &&
ww_ctx) by just (ww_ctx).
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210316153119.13802-2-longman@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2046a24ae121cd107929655a6aaf3b8c5beea01f ]
There is a possible chance that some cooling device stats buffer
allocation fails due to very high cooling device max state value.
Later cooling device update sysfs can try to access stats data
for the same cooling device. It will lead to NULL pointer
dereference issue.
Add a NULL pointer check before accessing thermal cooling device
stats data. It fixes the following bug
[ 26.812833] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
[ 27.122960] Call trace:
[ 27.122963] do_raw_spin_lock+0x18/0xe8
[ 27.122966] _raw_spin_lock+0x24/0x30
[ 27.128157] thermal_cooling_device_stats_update+0x24/0x98
[ 27.128162] cur_state_store+0x88/0xb8
[ 27.128166] dev_attr_store+0x40/0x58
[ 27.128169] sysfs_kf_write+0x50/0x68
[ 27.133358] kernfs_fop_write+0x12c/0x1c8
[ 27.133362] __vfs_write+0x54/0x160
[ 27.152297] vfs_write+0xcc/0x188
[ 27.157132] ksys_write+0x78/0x108
[ 27.162050] ksys_write+0xf8/0x108
[ 27.166968] __arm_smccc_hvc+0x158/0x4b0
[ 27.166973] __arm_smccc_hvc+0x9c/0x4b0
[ 27.186005] el0_svc+0x8/0xc
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1607367181-24589-1-git-send-email-manafm@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbf54a9534350d6aebbb34f5c1c606b81a4f35dd ]
Simple-card/audio-graph-card drivers do not handle MCLK clock when it
is specified in the codec device node. The expectation here is that,
the codec should actually own up the MCLK clock and do necessary setup
in the driver.
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1615829492-8972-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2d106fe3badfc3bf0dd3899d1c3f210c7203eab ]
request_irq() wont accept a name which contains slash so we need to
repalce it with something else -- otherwise it will trigger a warning
and the entry in /proc/irq/ will not be created
since the .name might be used by userspace and we don't want to break
userspace, so we are changing the parameters passed to request_irq()
[ 1.565966] name 'pci-das6402/16'
[ 1.566149] WARNING: CPU: 0 PID: 184 at fs/proc/generic.c:180 __xlate_proc_name+0x93/0xb0
[ 1.568923] RIP: 0010:__xlate_proc_name+0x93/0xb0
[ 1.574200] Call Trace:
[ 1.574722] proc_mkdir+0x18/0x20
[ 1.576629] request_threaded_irq+0xfe/0x160
[ 1.576859] auto_attach+0x60a/0xc40 [cb_pcidas64]
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210315195814.4692-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e5848a3d86f03024ae096478bdb892ab3d79131 ]
request_irq() wont accept a name which contains slash so we need to
repalce it with something else -- otherwise it will trigger a warning
and the entry in /proc/irq/ will not be created
since the .name might be used by userspace and we don't want to break
userspace, so we are changing the parameters passed to request_irq()
[ 1.630764] name 'pci-das1602/16'
[ 1.630950] WARNING: CPU: 0 PID: 181 at fs/proc/generic.c:180 __xlate_proc_name+0x93/0xb0
[ 1.634009] RIP: 0010:__xlate_proc_name+0x93/0xb0
[ 1.639441] Call Trace:
[ 1.639976] proc_mkdir+0x18/0x20
[ 1.641946] request_threaded_irq+0xfe/0x160
[ 1.642186] cb_pcidas_auto_attach+0xf4/0x610 [cb_pcidas]
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210315195914.4801-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5999b9e5b1f8a2f5417b755130919b3ac96f5550 ]
Only half of the file is under include guard because terminating #endif
is placed too early.
Link: https://lore.kernel.org/r/YE4snvoW1SuwcXAn@localhost.localdomain
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8c165dea4c8f5ad67b1240861e4f6c5395fa4ac ]
In st_open(), if STp->in_use is true, STp will be freed by
scsi_tape_put(). However, STp is still used by DEBC_printk() after. It is
better to DEBC_printk() before scsi_tape_put().
Link: https://lore.kernel.org/r/20210311064636.10522-1-lyl2019@mail.ustc.edu.cn
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beb691e69f4dec7bfe8b81b509848acfd1f0dbf9 ]
vhost_reset_is_le() is vhost_init_is_le(), and in the case of
cross-endian legacy, vhost_init_is_le() depends on vq->user_be.
vq->user_be is set by vhost_disable_cross_endian().
But in vhost_vq_reset(), we have:
vhost_reset_is_le(vq);
vhost_disable_cross_endian(vq);
And so user_be is used before being set.
To fix that, reverse the lines order as there is no other dependency
between them.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: https://lore.kernel.org/r/20210312140913.788592-1-lvivier@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed5fae00593ab9d261a0c1ffc1bdb786a87a55a ]
The code relies on constant folding of cpu_has_feature() based
on possible and always true values as defined per
CPU_FTRS_ALWAYS and CPU_FTRS_POSSIBLE.
Build failure is encountered with for instance
book3e_all_defconfig on kisskb in the AMDGPU driver which uses
cpu_has_feature(CPU_FTR_VSX_COMP) to decide whether calling
kernel_enable_vsx() or not.
The failure is due to cpu_has_feature() not being inlined with
that configuration with gcc 4.9.
In the same way as commit acdad8fb4a15 ("powerpc: Force inlining of
mmu_has_feature to fix build failure"), for inlining of
cpu_has_feature().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b231dfa040ce4cc37f702f5c3a595fdeabfe0462.1615378209.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4250dd868d1b42c0a65de11ef3afbee67ba5d2f ]
When the server tries to do a callback and a client fails it due to
authentication problems, we need the server to set callback down
flag in RENEW so that client can recover.
Suggested-by: Bruce Fields <bfields@redhat.com>
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Link: https://lore.kernel.org/linux-nfs/FB84E90A-1A03-48B3-8BF7-D9D10AC2C9FE@oracle.com/T/#t
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19325cfea04446bc79b36bffd4978af15f46a00e ]
This delay is part of the power-up sequence defined in the datasheet.
A runtime_resume is a power-up so must also include the delay.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-6-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72d904763ae6a8576e7ad034f9da4f0e3c44bf24 ]
The minimum value is 0x3f (-63dB), which also is mute
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-4-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bdc4f5c6838f7c3feb4fe68e4edbeea158ec0a2 ]
Remove the hard coded 32 bits width and replace with the correct width
calculated by params_width.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-3-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e793c965519b8b7f2fea51a48398405e2a501729 ]
The driver was setting bit clock polarity opposite to intended polarity.
Also simplify the code by grouping ADC and DAC clock configurations into
a single field.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb18c678754ce1514100fb4c0bf6113b5af36c48 ]
Most steps in this table are steps of 3dB (300 centi-dB), so we can
simplify the table.
This not only reduces the amount of space it takes inside the kernel,
this also makes alsa-lib's mixer code actually accept the table, where
as before this change alsa-lib saw the "ADC PGA Gain" control as a
control without a dB scale.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210228160441.241110-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f86f58e3594fb0ab1993d833d3b9a2496f3c928c ]
According to the SGTL5000 datasheet [1], the DAP_AVC_CTRL register has
the following bit field definitions:
| BITS | FIELD | RW | RESET | DEFINITION |
| 15 | RSVD | RO | 0x0 | Reserved |
| 14 | RSVD | RW | 0x1 | Reserved |
| 13:12 | MAX_GAIN | RW | 0x1 | Max Gain of AVC in expander mode |
| 11:10 | RSVD | RO | 0x0 | Reserved |
| 9:8 | LBI_RESP | RW | 0x1 | Integrator Response |
| 7:6 | RSVD | RO | 0x0 | Reserved |
| 5 | HARD_LMT_EN | RW | 0x0 | Enable hard limiter mode |
| 4:1 | RSVD | RO | 0x0 | Reserved |
| 0 | EN | RW | 0x0 | Enable/Disable AVC |
The original default value written to the DAP_AVC_CTRL register during
sgtl5000_i2c_probe() was 0x0510. This would incorrectly write values to
bits 4 and 10, which are defined as RESERVED. It would also not set
bits 12 and 14 to their correct RESET values of 0x1, and instead set
them to 0x0. While the DAP_AVC module is effectively disabled because
the EN bit is 0, this default value is still writing invalid values to
registers that are marked as read-only and RESERVED as well as not
setting bits 12 and 14 to their correct default values as defined by the
datasheet.
The correct value that should be written to the DAP_AVC_CTRL register is
0x5100, which configures the register bits to the default values defined
by the datasheet, and prevents any writes to bits defined as
'read-only'. Generally speaking, it is best practice to NOT attempt to
write values to registers/bits defined as RESERVED, as it generally
produces unwanted/undefined behavior, or errors.
Also, all credit for this patch should go to my colleague Dan MacDonald
<dmacdonald@curbellmedical.com> for finding this error in the first
place.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Signed-off-by: Benjamin Rood <benjaminjrood@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210219183308.GA2117@ubuntu-dev
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eee51df776bd6cac10a76b2779a9fdee3f622b2b ]
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b540 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfa26ed1f9f885c2fd8f53ca492989d1e16d0199 ]
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b540 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5808fecc572391867fcd929662b29c12e6d08d81 ]
In case if isi.nr_pages is 0, we are making sis->pages (which is
unsigned int) a huge value in iomap_swapfile_activate() by assigning -1.
This could cause a kernel crash in kernel v4.18 (with below signature).
Or could lead to unknown issues on latest kernel if the fake big swap gets
used.
Fix this issue by returning -EINVAL in case of nr_pages is 0, since it
is anyway a invalid swapfile. Looks like this issue will be hit when
we have pagesize < blocksize type of configuration.
I was able to hit the issue in case of a tiny swap file with below
test script.
https://raw.githubusercontent.com/riteshharjani/LinuxStudy/master/scripts/swap-issue.sh
kernel crash analysis on v4.18
==============================
On v4.18 kernel, it causes a kernel panic, since sis->pages becomes
a huge value and isi.nr_extents is 0. When 0 is returned it is
considered as a swapfile over NFS and SWP_FILE is set (sis->flags |= SWP_FILE).
Then when swapoff was getting called it was calling a_ops->swap_deactivate()
if (sis->flags & SWP_FILE) is true. Since a_ops->swap_deactivate() is
NULL in case of XFS, it causes below panic.
Panic signature on v4.18 kernel:
=======================================
root@qemu:/home/qemu# [ 8291.723351] XFS (loop2): Unmounting Filesystem
[ 8292.123104] XFS (loop2): Mounting V5 Filesystem
[ 8292.132451] XFS (loop2): Ending clean mount
[ 8292.263362] Adding 4294967232k swap on /mnt1/test/swapfile. Priority:-2 extents:1 across:274877906880k
[ 8292.277834] Unable to handle kernel paging request for instruction fetch
[ 8292.278677] Faulting instruction address: 0x00000000
cpu 0x19: Vector: 400 (Instruction Access) at [c0000009dd5b7ad0]
pc: 0000000000000000
lr: c0000000003eb9dc: destroy_swap_extents+0xfc/0x120
sp: c0000009dd5b7d50
msr: 8000000040009033
current = 0xc0000009b6710080
paca = 0xc00000003ffcb280 irqmask: 0x03 irq_happened: 0x01
pid = 5604, comm = swapoff
Linux version 4.18.0 (riteshh@xxxxxxx) (gcc version 8.4.0 (Ubuntu 8.4.0-1ubuntu1~18.04)) #57 SMP Wed Mar 3 01:33:04 CST 2021
enter ? for help
[link register ] c0000000003eb9dc destroy_swap_extents+0xfc/0x120
[c0000009dd5b7d50] c0000000025a7058 proc_poll_event+0x0/0x4 (unreliable)
[c0000009dd5b7da0] c0000000003f0498 sys_swapoff+0x3f8/0x910
[c0000009dd5b7e30] c00000000000bbe4 system_call+0x5c/0x70
Exception: c01 (System Call) at 00007ffff7d208d8
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
[djwong: rework the comment to provide more details]
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ddc942394013f08992fc379ca04cffacbbe3dae ]
I think this is unlikely but possible:
svc_authenticate sets rq_authop and calls svcauth_gss_accept. The
kmalloc(sizeof(*svcdata), GFP_KERNEL) fails, leaving rq_auth_data NULL,
and returning SVC_DENIED.
This causes svc_process_common to go to err_bad_auth, and eventually
call svc_authorise. That calls ->release == svcauth_gss_release, which
tries to dereference rq_auth_data.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Link: https://lore.kernel.org/linux-nfs/3F1B347F-B809-478F-A1E9-0BE98E22B0F0@oracle.com/T/#t
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7005227369079963d25fb2d5d736d0feb2c44cf6 ]
When NFSD_V4 is enabled and CRYPTO is disabled,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for CRYPTO_SHA256
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- NFSD_V4 [=y] && NETWORK_FILESYSTEMS [=y] && NFSD [=y] && PROC_FS [=y]
WARNING: unmet direct dependencies detected for CRYPTO_MD5
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- NFSD_V4 [=y] && NETWORK_FILESYSTEMS [=y] && NFSD [=y] && PROC_FS [=y]
This is because NFSD_V4 selects CRYPTO_MD5 and CRYPTO_SHA256,
without depending on or selecting CRYPTO, despite those config options
being subordinate to CRYPTO.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efc61345274d6c7a46a0570efbc916fcbe3e927b ]
When generic/371 is run on kvm-xfstests using 5.10 and 5.11 kernels, it
fails at significant rates on the two test scenarios that disable
delayed allocation (ext3conv and data_journal) and force actual block
allocation for the fallocate and pwrite functions in the test. The
failure rate on 5.10 for both ext3conv and data_journal on one test
system typically runs about 85%. On 5.11, the failure rate on ext3conv
sometimes drops to as low as 1% while the rate on data_journal
increases to nearly 100%.
The observed failures are largely due to ext4_should_retry_alloc()
cutting off block allocation retries when s_mb_free_pending (used to
indicate that a transaction in progress will free blocks) is 0.
However, free space is usually available when this occurs during runs
of generic/371. It appears that a thread attempting to allocate
blocks is just missing transaction commits in other threads that
increase the free cluster count and reset s_mb_free_pending while
the allocating thread isn't running. Explicitly testing for free space
availability avoids this race.
The current code uses a post-increment operator in the conditional
expression that determines whether the retry limit has been exceeded.
This means that the conditional expression uses the value of the
retry counter before it's increased, resulting in an extra retry cycle.
The current code actually retries twice before hitting its retry limit
rather than once.
Increasing the retry limit to 3 from the current actual maximum retry
count of 2 in combination with the change described above reduces the
observed failure rate to less that 0.1% on both ext3conv and
data_journal with what should be limited impact on users sensitive to
the overhead caused by retries.
A per filesystem percpu counter exported via sysfs is added to allow
users or developers to track the number of times the retry limit is
exceeded without resorting to debugging methods. This should provide
some insight into worst case retry behavior.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Link: https://lore.kernel.org/r/20210218151132.19678-1-enwlinux@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec2a29593c83ed71a7f16e3243941ebfcf75fdf6 ]
5fdc7db644 ("module: setup load info before module_sig_check()")
moved the ELF setup, so that it was done before the signature
check. This made the module name available to signature error
messages.
However, the checks for ELF correctness in setup_load_info
are not sufficient to prevent bad memory references due to
corrupted offset fields, indices, etc.
So, there's a regression in behavior here: a corrupt and unsigned
(or badly signed) module, which might previously have been rejected
immediately, can now cause an oops/crash.
Harden ELF handling for module loading by doing the following:
- Move the signature check back up so that it comes before ELF
initialization. It's best to do the signature check to see
if we can trust the module, before using the ELF structures
inside it. This also makes checks against info->len
more accurate again, as this field will be reduced by the
length of the signature in mod_check_sig().
The module name is now once again not available for error
messages during the signature check, but that seems like
a fair tradeoff.
- Check if sections have offset / size fields that at least don't
exceed the length of the module.
- Check if sections have section name offsets that don't fall
outside the section name table.
- Add a few other sanity checks against invalid section indices,
etc.
This is not an exhaustive consistency check, but the idea is to
at least get through the signature and blacklist checks without
crashing because of corrupted ELF info, and to error out gracefully
for most issues that would have caused problems later on.
Fixes: 5fdc7db644 ("module: setup load info before module_sig_check()")
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10ccd1abb808599a6dc7c9389560016ea3568085 ]
Let's move the common handling of the non-fatal errors after the *switch*
statement -- this avoids *goto*s inside that *switch*...
Suggested-by: Joe Perches <joe@perches.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 705e9195187d85249fbb0eaa844b1604a98fbc9a ]
The 'reason' variable in module_sig_check() points to 3 strings across
the *switch* statement, all needlessly starting with the same text.
Let's put the starting text into the pr_notice() call -- it saves 21
bytes of the object code (x86 gcc 10.2.1).
Suggested-by: Joe Perches <joe@perches.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9f35f634e099894f4d6c3b039cd3de5281ee637 ]
It is useful to know which module failed signature verification, so
print the module name along with the error message.
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcc32f4f183ab8479041b23a1525d48233df1d43 ]
This reverts commit 6af1799aaf.
Commit 6af1799aaf ("ipv6: drop incoming packets having a v4mapped
source address") introduced an input check against v4mapped addresses.
Use of such addresses on the wire is indeed questionable and not
allowed on public Internet. As the commit pointed out
https://tools.ietf.org/html/draft-itojun-v6ops-v4mapped-harmful-02
lists potential issues.
Unfortunately there are applications which use v4mapped addresses,
and breaking them is a clear regression. For example v4mapped
addresses (or any semi-valid addresses, really) may be used
for uni-direction event streams or packet export.
Since the issue which sparked the addition of the check was with
TCP and request_socks in particular push the check down to TCPv6
and DCCP. This restores the ability to receive UDPv6 packets with
v4mapped address as the source.
Keep using the IPSTATS_MIB_INHDRERRORS statistic to minimize the
user-visible changes.
Fixes: 6af1799aaf ("ipv6: drop incoming packets having a v4mapped source address")
Reported-by: Sunyi Shao <sunyishao@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f935e8e72ec28dddb2dc0650b3b6626a293d94b ]
For AF_VSOCK, accept() currently returns sockets that are unlabelled.
Other socket families derive the child's SID from the SID of the parent
and the SID of the incoming packet. This is typically done as the
connected socket is placed in the queue that accept() removes from.
Reuse the existing 'security_sk_clone' hook to copy the SID from the
parent (server) socket to the child. There is no packet SID in this
case.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: David Brazdil <dbrazdil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a846738f8c3788d846ed1f587270d2f2e3d32432 upstream.
The fix for XSA-365 zapped too many of the ->persistent_gnt[] entries.
Ones successfully obtained should not be overwritten, but instead left
for xen_blkbk_unmap_prepare() to pick up and put.
This is XSA-371.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d7047ed6b7214fbabc16d8712a822e256b1aa44 upstream.
In commit 6417f03132a6 ("module: remove never implemented
MODULE_SUPPORTED_DEVICE") the MODULE_SUPPORTED_DEVICE macro was
removed from the kerne entirely. Shortly before this patch was applied
mainline the commit 59ec7b89ed3e ("can: peak_usb: add forgotten
supported devices") was added to net/master. As this would result in a
merge conflict, let's revert this patch.
Fixes: 59ec7b89ed3e ("can: peak_usb: add forgotten supported devices")
Link: https://lore.kernel.org/r/20210320192649.341832-1-mkl@pengutronix.de
Suggested-by: Leon Romanovsky <leon@kernel.org>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 163f0ec1df33cf468509ff38cbcbb5eb0d7fac60 upstream.
Syzbot is reporting that ext4 can enter fs reclaim from kvmalloc() while
the transaction is started like:
fs_reclaim_acquire+0x117/0x150 mm/page_alloc.c:4340
might_alloc include/linux/sched/mm.h:193 [inline]
slab_pre_alloc_hook mm/slab.h:493 [inline]
slab_alloc_node mm/slub.c:2817 [inline]
__kmalloc_node+0x5f/0x430 mm/slub.c:4015
kmalloc_node include/linux/slab.h:575 [inline]
kvmalloc_node+0x61/0xf0 mm/util.c:587
kvmalloc include/linux/mm.h:781 [inline]
ext4_xattr_inode_cache_find fs/ext4/xattr.c:1465 [inline]
ext4_xattr_inode_lookup_create fs/ext4/xattr.c:1508 [inline]
ext4_xattr_set_entry+0x1ce6/0x3780 fs/ext4/xattr.c:1649
ext4_xattr_ibody_set+0x78/0x2b0 fs/ext4/xattr.c:2224
ext4_xattr_set_handle+0x8f4/0x13e0 fs/ext4/xattr.c:2380
ext4_xattr_set+0x13a/0x340 fs/ext4/xattr.c:2493
This should be impossible since transaction start sets PF_MEMALLOC_NOFS.
Add some assertions to the code to catch if something isn't working as
expected early.
Link: https://lore.kernel.org/linux-ext4/000000000000563a0205bafb7970@google.com/
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20210222171626.21884-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d45c36bafb94e72fdb6dee437279b61b6d97e706 upstream.
The bcm_sf2 driver uses the b53 driver as a library but does not make
usre of the b53_setup() function, this made it fail to inherit the
vlan_filtering_is_global attribute. Fix this by moving the assignment to
b53_switch_alloc() which is used by bcm_sf2.
Fixes: 7228b23e68 ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a5ca857079ea022e0b1b17fc154f7ad7dbc150f upstream.
When a non-initial netns is destroyed, the usual policy is to delete
all virtual network interfaces contained, but move physical interfaces
back to the initial netns. This keeps the physical interface visible
on the system.
CAN devices are somewhat special, as they define rtnl_link_ops even
if they are physical devices. If a CAN interface is moved into a
non-initial netns, destroying that netns lets the interface vanish
instead of moving it back to the initial netns. default_device_exit()
skips CAN interfaces due to having rtnl_link_ops set. Reproducer:
ip netns add foo
ip link set can0 netns foo
ip netns delete foo
WARNING: CPU: 1 PID: 84 at net/core/dev.c:11030 ops_exit_list+0x38/0x60
CPU: 1 PID: 84 Comm: kworker/u4:2 Not tainted 5.10.19 #1
Workqueue: netns cleanup_net
[<c010e700>] (unwind_backtrace) from [<c010a1d8>] (show_stack+0x10/0x14)
[<c010a1d8>] (show_stack) from [<c086dc10>] (dump_stack+0x94/0xa8)
[<c086dc10>] (dump_stack) from [<c086b938>] (__warn+0xb8/0x114)
[<c086b938>] (__warn) from [<c086ba10>] (warn_slowpath_fmt+0x7c/0xac)
[<c086ba10>] (warn_slowpath_fmt) from [<c0629f20>] (ops_exit_list+0x38/0x60)
[<c0629f20>] (ops_exit_list) from [<c062a5c4>] (cleanup_net+0x230/0x380)
[<c062a5c4>] (cleanup_net) from [<c0142c20>] (process_one_work+0x1d8/0x438)
[<c0142c20>] (process_one_work) from [<c0142ee4>] (worker_thread+0x64/0x5a8)
[<c0142ee4>] (worker_thread) from [<c0148a98>] (kthread+0x148/0x14c)
[<c0148a98>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c)
To properly restore physical CAN devices to the initial netns on owning
netns exit, introduce a flag on rtnl_link_ops that can be set by drivers.
For CAN devices setting this flag, default_device_exit() considers them
non-virtual, applying the usual namespace move.
The issue was introduced in the commit mentioned below, as at that time
CAN devices did not have a dellink() operation.
Fixes: e008b5fc8d ("net: Simplfy default_device_exit and improve batching.")
Link: https://lore.kernel.org/r/20210302122423.872326-1-martin@strongswan.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8249d17d3194eac064a8ca5bc5ca0abc86feecde upstream.
The pfn variable contains the page frame number as returned by the
pXX_pfn() functions, shifted to the right by PAGE_SHIFT to remove the
page bits. After page protection computations are done to it, it gets
shifted back to the physical address using page_level_shift().
That is wrong, of course, because that function determines the shift
length based on the level of the page in the page table but in all the
cases, it was shifted by PAGE_SHIFT before.
Therefore, shift it back using PAGE_SHIFT to get the correct physical
address.
[ bp: Rewrite commit message. ]
Fixes: dfaaec9033 ("x86: Add support for changing memory encryption attribute in early boot")
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/81abbae1657053eccc535c16151f63cd049dcb97.1616098294.git.isaku.yamahata@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 291da9d4a9eb3a1cb0610b7f4480f5b52b1825e7 upstream.
If CONFIG_DEBUG_LOCK_ALLOC=n then mutex_lock_io_nested() maps to
mutex_lock() which is clearly wrong because mutex_lock() lacks the
io_schedule_prepare()/finish() invocations.
Map it to mutex_lock_io().
Fixes: f21860bac0 ("locking/mutex, sched/wait: Fix the mutex_lock_io_nested() define")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/878s6fshii.fsf@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3401ecf7fc1b9458a19d42c0e26a228f18ac7dda ]
When kzalloc() returns NULL, no error return code of mpt3sas_base_attach()
is assigned. To fix this bug, r is assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308035241.3288-1-baijiaju1990@gmail.com
Fixes: c696f7b83e ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Doug Brown