rxrpc_disconnect_client_call() reads the call's connection ID protocol
value (call->cid) as part of that function's variable declarations. This
is bad because it's not inside the locked section and so may race with
someone granting use of the channel to the call.
This manifests as an assertion failure (see below) where the call in the
presumed channel (0 because call->cid wasn't set when we read it) doesn't
match the call attached to the channel we were actually granted (if 1, 2 or
3).
Fix this by moving the read and dependent calculations inside of the
channel_lock section. Also, only set the channel number and pointer
variables if cid is not zero (ie. unset).
This problem can be induced by injecting an occasional error in
rxrpc_wait_for_channel() before the call to schedule().
Make two further changes also:
(1) Add a trace for wait failure in rxrpc_connect_call().
(2) Drop channel_lock before BUG'ing in the case of the assertion failure.
The failure causes a trace akin to the following:
rxrpc: Assertion failed - 18446612685268945920(0xffff8880beab8c00) == 18446612685268621312(0xffff8880bea69800) is false
------------[ cut here ]------------
kernel BUG at net/rxrpc/conn_client.c:824!
...
RIP: 0010:rxrpc_disconnect_client_call+0x2bf/0x99d
...
Call Trace:
rxrpc_connect_call+0x902/0x9b3
? wake_up_q+0x54/0x54
rxrpc_new_client_call+0x3a0/0x751
? rxrpc_kernel_begin_call+0x141/0x1bc
? afs_alloc_call+0x1b5/0x1b5
rxrpc_kernel_begin_call+0x141/0x1bc
afs_make_call+0x20c/0x525
? afs_alloc_call+0x1b5/0x1b5
? __lock_is_held+0x40/0x71
? lockdep_init_map+0xaf/0x193
? lockdep_init_map+0xaf/0x193
? __lock_is_held+0x40/0x71
? yfs_fs_fetch_data+0x33b/0x34a
yfs_fs_fetch_data+0x33b/0x34a
afs_fetch_data+0xdc/0x3b7
afs_read_dir+0x52d/0x97f
afs_dir_iterate+0xa0/0x661
? iterate_dir+0x63/0x141
iterate_dir+0xa2/0x141
ksys_getdents64+0x9f/0x11b
? filldir+0x111/0x111
? do_syscall_64+0x3e/0x1a0
__x64_sys_getdents64+0x16/0x19
do_syscall_64+0x7d/0x1a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 45025bceef ("rxrpc: Improve management and caching of client connection objects")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes introduced to allow rxrpc calls to be retried creates an issue
when it comes to refcounting afs_call structs. The problem is that when
rxrpc_send_data() queues the last packet for an asynchronous call, the
following sequence can occur:
(1) The notify_end_tx callback is invoked which causes the state in the
afs_call to be changed from AFS_CALL_CL_REQUESTING or
AFS_CALL_SV_REPLYING.
(2) afs_deliver_to_call() can then process event notifications from rxrpc
on the async_work queue.
(3) Delivery of events, such as an abort from the server, can cause the
afs_call state to be changed to AFS_CALL_COMPLETE on async_work.
(4) For an asynchronous call, afs_process_async_call() notes that the call
is complete and tried to clean up all the refs on async_work.
(5) rxrpc_send_data() might return the amount of data transferred
(success) or an error - which could in turn reflect a local error or a
received error.
Synchronising the clean up after rxrpc_kernel_send_data() returns an error
with the asynchronous cleanup is then tricky to get right.
Mostly revert commit c038a58ccf. The two API
functions the original commit added aren't currently used. This makes
rxrpc_kernel_send_data() always return successfully if it queued the data
it was given.
Note that this doesn't affect synchronous calls since their Rx notification
function merely pokes a wait queue and does not refcounting. The
asynchronous call notification function *has* to do refcounting and pass a
ref over the work item to avoid the need to sync the workqueue in call
cleanup.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The life-checking function, which is used by kAFS to make sure that a call
is still live in the event of a pending signal, only samples the received
packet serial number counter; it doesn't actually provoke a change in the
counter, rather relying on the server to happen to give us a packet in the
time window.
Fix this by adding a function to force a ping to be transmitted.
kAFS then keeps track of whether there's been a stall, and if so, uses the
new function to ping the server, resetting the timeout to allow the reply
to come back.
If there's a stall, a ping and the call is *still* stalled in the same
place after another period, then the call will be aborted.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Fixes: f4d15fb6f9 ("rxrpc: Provide functions for allowing cleaner handling of signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the network becomes (partially) unavailable, say by disabling IPv6, the
background ACK transmission routine can get itself into a tizzy by
proposing immediate ACK retransmission. Since we're in the call event
processor, that happens immediately without returning to the workqueue
manager.
The condition should clear after a while when either the network comes back
or the call times out.
Fix this by:
(1) When re-proposing an ACK on failed Tx, don't schedule it immediately.
This will allow a certain amount of time to elapse before we try
again.
(2) Enforce a return to the workqueue manager after a certain number of
iterations of the call processing loop.
(3) Add a backoff delay that increases the delay on deferred ACKs by a
jiffy per failed transmission to a limit of HZ. The backoff delay is
cleared on a successful return from kernel_sendmsg().
(4) Cancel calls immediately if the opening sendmsg fails. The layer
above can arrange retransmission or rotate to another server.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dd979b4df8.
This broke tcp_poll for SMC fallback: An AF_SMC socket establishes an
internal TCP socket for the initial handshake with the remote peer.
Whenever the SMC connection can not be established this TCP socket is
used as a fallback. All socket operations on the SMC socket are then
forwarded to the TCP socket. In case of poll, the file->private_data
pointer references the SMC socket because the TCP socket has no file
assigned. This causes tcp_poll to wait on the wrong socket.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a missing call to rxrpc_put_peer() on the main path through the
rxrpc_error_report() function. This manifests itself as a ref leak
whenever an ICMP packet or other error comes in.
In commit f334430316, the hand-off of the ref to a work item was removed
and was not replaced with a put.
Fixes: f334430316 ("rxrpc: Fix error distribution")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add /proc/net/rxrpc/peers to display the list of peers currently active.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udpv6_encap_enable() function is part of the ipv6 code, and if that is
configured as a loadable module and rxrpc is built in then a build failure
will occur because the conditional check is wrong:
net/rxrpc/local_object.o: In function `rxrpc_lookup_local':
local_object.c:(.text+0x2688): undefined reference to `udpv6_encap_enable'
Use the correct config symbol (CONFIG_AF_RXRPC_IPV6) in the conditional
check rather than CONFIG_IPV6 as that will do the right thing.
Fixes: 5271953cad ("rxrpc: Use the UDP encap_rcv hook")
Reported-by: kbuild-all@01.org
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/rxrpc/output.c: In function 'rxrpc_reject_packets':
net/rxrpc/output.c:527:11: warning:
variable 'ioc' set but not used [-Wunused-but-set-variable]
'ioc' is the correct kvec num when sending a BUSY (or an ABORT) response
packet.
Fixes: ece64fec16 ("rxrpc: Emit BUSY packets when supposed to rather than ABORTs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an uninitialised variable introduced by the last patch. This can cause
a crash when a new call comes in to a local service, such as when an AFS
fileserver calls back to the local cache manager.
Fixes: c1e15b4944 ("rxrpc: Fix the packet reception routine")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
The rxrpc_input_packet() function and its call tree was built around the
assumption that data_ready() handler called from UDP to inform a kernel
service that there is data to be had was non-reentrant. This means that
certain locking could be dispensed with.
This, however, turns out not to be the case with a multi-queue network card
that can deliver packets to multiple cpus simultaneously. Each of those
cpus can be in the rxrpc_input_packet() function at the same time.
Fix by adding or changing some structure members:
(1) Add peer->rtt_input_lock to serialise access to the RTT buffer.
(2) Make conn->service_id into a 32-bit variable so that it can be
cmpxchg'd on all arches.
(3) Add call->input_lock to serialise access to the Rx/Tx state. Note
that although the Rx and Tx states are (almost) entirely separate,
there's no point completing the separation and having separate locks
since it's a bi-phasal RPC protocol rather than a bi-direction
streaming protocol. Data transmission and data reception do not take
place simultaneously on any particular call.
and making the following functional changes:
(1) In rxrpc_input_data(), hold call->input_lock around the core to
prevent simultaneous producing of packets into the Rx ring and
updating of tracking state for a particular call.
(2) In rxrpc_input_ping_response(), only read call->ping_serial once, and
check it before checking RXRPC_CALL_PINGING as that's a cheaper test.
The bit test and bit clear can then be combined. No further locking
is needed here.
(3) In rxrpc_input_ack(), take call->input_lock after we've parsed much of
the ACK packet. The superseded ACK check is then done both before and
after the lock is taken.
The handing of ackinfo data is split, parsing before the lock is taken
and processing with it held. This is keyed on rxMTU being non-zero.
Congestion management is also done within the locked section.
(4) In rxrpc_input_ackall(), take call->input_lock around the Tx window
rotation. The ACKALL packet carries no information and is only really
useful after all packets have been transmitted since it's imprecise.
(5) In rxrpc_input_implicit_end_call(), we use rx->incoming_lock to
prevent calls being simultaneously implicitly ended on two cpus and
also to prevent any races with incoming call setup.
(6) In rxrpc_input_packet(), use cmpxchg() to effect the service upgrade
on a connection. It is only permitted to happen once for a
connection.
(7) In rxrpc_new_incoming_call(), we have to recheck the routing inside
rx->incoming_lock to see if someone else set up the call, connection
or peer whilst we were getting there. We can't trust the values from
the earlier routing check unless we pin refs on them - which we want
to avoid.
Further, we need to allow for an incoming call to have its state
changed on another CPU between us making it live and us adjusting it
because the conn is now in the RXRPC_CONN_SERVICE state.
(8) In rxrpc_peer_add_rtt(), take peer->rtt_input_lock around the access
to the RTT buffer. Don't need to lock around setting peer->rtt.
For reference, the inventory of state-accessing or state-altering functions
used by the packet input procedure is:
> rxrpc_input_packet()
* PACKET CHECKING
* ROUTING
> rxrpc_post_packet_to_local()
> rxrpc_find_connection_rcu() - uses RCU
> rxrpc_lookup_peer_rcu() - uses RCU
> rxrpc_find_service_conn_rcu() - uses RCU
> idr_find() - uses RCU
* CONNECTION-LEVEL PROCESSING
- Service upgrade
- Can only happen once per conn
! Changed to use cmpxchg
> rxrpc_post_packet_to_conn()
- Setting conn->hi_serial
- Probably safe not using locks
- Maybe use cmpxchg
* CALL-LEVEL PROCESSING
> Old-call checking
> rxrpc_input_implicit_end_call()
> rxrpc_call_completed()
> rxrpc_queue_call()
! Need to take rx->incoming_lock
> __rxrpc_disconnect_call()
> rxrpc_notify_socket()
> rxrpc_new_incoming_call()
- Uses rx->incoming_lock for the entire process
- Might be able to drop this earlier in favour of the call lock
> rxrpc_incoming_call()
! Conflicts with rxrpc_input_implicit_end_call()
> rxrpc_send_ping()
- Don't need locks to check rtt state
> rxrpc_propose_ACK
* PACKET DISTRIBUTION
> rxrpc_input_call_packet()
> rxrpc_input_data()
* QUEUE DATA PACKET ON CALL
> rxrpc_reduce_call_timer()
- Uses timer_reduce()
! Needs call->input_lock()
> rxrpc_receiving_reply()
! Needs locking around ack state
> rxrpc_rotate_tx_window()
> rxrpc_end_tx_phase()
> rxrpc_proto_abort()
> rxrpc_input_dup_data()
- Fills the Rx buffer
- rxrpc_propose_ACK()
- rxrpc_notify_socket()
> rxrpc_input_ack()
* APPLY ACK PACKET TO CALL AND DISCARD PACKET
> rxrpc_input_ping_response()
- Probably doesn't need any extra locking
! Need READ_ONCE() on call->ping_serial
> rxrpc_input_check_for_lost_ack()
- Takes call->lock to consult Tx buffer
> rxrpc_peer_add_rtt()
! Needs to take a lock (peer->rtt_input_lock)
! Could perhaps manage with cmpxchg() and xadd() instead
> rxrpc_input_requested_ack
- Consults Tx buffer
! Probably needs a lock
> rxrpc_peer_add_rtt()
> rxrpc_propose_ack()
> rxrpc_input_ackinfo()
- Changes call->tx_winsize
! Use cmpxchg to handle change
! Should perhaps track serial number
- Uses peer->lock to record MTU specification changes
> rxrpc_proto_abort()
! Need to take call->input_lock
> rxrpc_rotate_tx_window()
> rxrpc_end_tx_phase()
> rxrpc_input_soft_acks()
- Consults the Tx buffer
> rxrpc_congestion_management()
- Modifies the Tx annotations
! Needs call->input_lock()
> rxrpc_queue_call()
> rxrpc_input_abort()
* APPLY ABORT PACKET TO CALL AND DISCARD PACKET
> rxrpc_set_call_completion()
> rxrpc_notify_socket()
> rxrpc_input_ackall()
* APPLY ACKALL PACKET TO CALL AND DISCARD PACKET
! Need to take call->input_lock
> rxrpc_rotate_tx_window()
> rxrpc_end_tx_phase()
> rxrpc_reject_packet()
There are some functions used by the above that queue the packet, after
which the procedure is terminated:
- rxrpc_post_packet_to_local()
- local->event_queue is an sk_buff_head
- local->processor is a work_struct
- rxrpc_post_packet_to_conn()
- conn->rx_queue is an sk_buff_head
- conn->processor is a work_struct
- rxrpc_reject_packet()
- local->reject_queue is an sk_buff_head
- local->processor is a work_struct
And some that offload processing to process context:
- rxrpc_notify_socket()
- Uses RCU lock
- Uses call->notify_lock to call call->notify_rx
- Uses call->recvmsg_lock to queue recvmsg side
- rxrpc_queue_call()
- call->processor is a work_struct
- rxrpc_propose_ACK()
- Uses call->lock to wrap __rxrpc_propose_ACK()
And a bunch that complete a call, all of which use call->state_lock to
protect the call state:
- rxrpc_call_completed()
- rxrpc_set_call_completion()
- rxrpc_abort_call()
- rxrpc_proto_abort()
- Also uses rxrpc_queue_call()
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix connection-level abort handling to cache the abort and error codes
properly so that a new incoming call can be properly aborted if it races
with the parent connection being aborted by another CPU.
The abort_code and error parameters can then be dropped from
rxrpc_abort_calls().
Fixes: f5c17aaeb2 ("rxrpc: Calls should only have one terminal state")
Signed-off-by: David Howells <dhowells@redhat.com>
Move the out-of-order and duplicate ACK packet check to before the call to
rxrpc_input_ackinfo() so that the receive window size and MTU size are only
checked in the latest ACK packet and don't regress.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Carry the call state out of the locked section in rxrpc_rotate_tx_window()
rather than sampling it afterwards. This is only used to select tracepoint
data, but could have changed by the time we do the tracepoint.
Signed-off-by: David Howells <dhowells@redhat.com>
We should only call the function to end a call's Tx phase if we rotated the
marked-last packet out of the transmission buffer.
Make rxrpc_rotate_tx_window() return an indication of whether it just
rotated the packet marked as the last out of the transmit buffer, carrying
the information out of the locked section in that function.
We can then check the return value instead of examining RXRPC_CALL_TX_LAST.
Fixes: 70790dbe3f ("rxrpc: Pass the last Tx packet marker in the annotation buffer")
Signed-off-by: David Howells <dhowells@redhat.com>
We don't need to take the RCU read lock in the rxrpc packet receive
function because it's held further up the stack in the IP input routine
around the UDP receive routines.
Fix this by dropping the RCU read lock calls from rxrpc_input_packet().
This simplifies the code.
Fixes: 70790dbe3f ("rxrpc: Pass the last Tx packet marker in the annotation buffer")
Signed-off-by: David Howells <dhowells@redhat.com>
Use the UDP encap_rcv hook to cut the bit out of the rxrpc packet reception
in which a packet is placed onto the UDP receive queue and then immediately
removed again by rxrpc. Going via the queue in this manner seems like it
should be unnecessary.
This does, however, require the invention of a value to place in encap_type
as that's one of the conditions to switch packets out to the encap_rcv
hook. Possibly the value doesn't actually matter for anything other than
sockopts on the UDP socket, which aren't accessible outside of rxrpc
anyway.
This seems to cut a bit of time out of the time elapsed between each
sk_buff being timestamped and turning up in rxrpc (the final number in the
following trace excerpts). I measured this by making the rxrpc_rx_packet
trace point print the time elapsed between the skb being timestamped and
the current time (in ns), e.g.:
... 424.278721: rxrpc_rx_packet: ... ACK 25026
So doing a 512MiB DIO read from my test server, with an unmodified kernel:
N min max sum mean stddev
27605 2626 7581 7.83992e+07 2840.04 181.029
and with the patch applied:
N min max sum mean stddev
27547 1895 12165 6.77461e+07 2459.29 255.02
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the rxrpc_data_ready() function to pick up all packets and to not miss
any. There are two problems:
(1) The sk_data_ready pointer on the UDP socket is set *after* it is
bound. This means that it's open for business before we're ready to
dequeue packets and there's a tiny window exists in which a packet can
sneak onto the receive queue, but we never know about it.
Fix this by setting the pointers on the socket prior to binding it.
(2) skb_recv_udp() will return an error (such as ENETUNREACH) if there was
an error on the transmission side, even though we set the
sk_error_report hook. Because rxrpc_data_ready() returns immediately
in such a case, it never actually removes its packet from the receive
queue.
Fix this by abstracting out the UDP dequeuing and checksumming into a
separate function that keeps hammering on skb_recv_udp() until it
returns -EAGAIN, passing the packets extracted to the remainder of the
function.
and two potential problems:
(3) It might be possible in some circumstances or in the future for
packets to be being added to the UDP receive queue whilst rxrpc is
running consuming them, so the data_ready() handler might get called
less often than once per packet.
Allow for this by fully draining the queue on each call as (2).
(4) If a packet fails the checksum check, the code currently returns after
discarding the packet without checking for more.
Allow for this by fully draining the queue on each call as (2).
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Fix some refs to init_net that should've been changed to the appropriate
network namespace.
Fixes: 2baec2c3f8 ("rxrpc: Support network namespacing")
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Allow the epoch value to be queried on a server connection. This is in the
rxrpc header of every packet for use in routing and is derived from the
client's state. It's also not supposed to change unless the client gets
restarted.
AFS can make use of this information to deduce whether a fileserver has
been restarted because the fileserver makes client calls to the filesystem
driver's cache manager to send notifications (ie. callback breaks) about
conflicting changes from other clients. These convey the fileserver's own
epoch value back to the filesystem.
Signed-off-by: David Howells <dhowells@redhat.com>
Allow the timestamp on the sk_buff holding the first DATA packet of a reply
to be queried. This can then be used as a base for the expiry time
calculation on the callback promise duration indicated by an operation
result.
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_extract_addr_from_skb() doesn't use the argument that points to the
local endpoint, so remove the argument.
Signed-off-by: David Howells <dhowells@redhat.com>
AF_RXRPC opens an IPv6 socket through which to send and receive network
packets, both IPv6 and IPv4. It currently turns AF_INET addresses into
AF_INET-as-AF_INET6 addresses based on an assumption that this was
necessary; on further inspection of the code, however, it turns out that
the IPv6 code just farms packets aimed at AF_INET addresses out to the IPv4
code.
Fix AF_RXRPC to use AF_INET addresses directly when given them.
Fixes: 7b674e390e ("rxrpc: Fix IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Print the data Tx trace line before transmitting so that it appears before
the trace lines indicating success or failure of the transmission. This
makes the trace log less confusing.
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_lose_skb() is now exactly the same as rxrpc_free_skb(), so remove it
and use the latter instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix error distribution by immediately delivering the errors to all the
affected calls rather than deferring them to a worker thread. The problem
with the latter is that retries and things can happen in the meantime when we
want to stop that sooner.
To this end:
(1) Stop the error distributor from removing calls from the error_targets
list so that peer->lock isn't needed to synchronise against other adds
and removals.
(2) Require the peer's error_targets list to be accessed with RCU, thereby
avoiding the need to take peer->lock over distribution.
(3) Don't attempt to affect a call's state if it is already marked complete.
Signed-off-by: David Howells <dhowells@redhat.com>
It seems that enabling IPV6_RECVERR on an IPv6 socket doesn't also turn on
IP_RECVERR, so neither local errors nor ICMP-transported remote errors from
IPv4 peer addresses are returned to the AF_RXRPC protocol.
Make the sockopt setting code in rxrpc_open_socket() fall through from the
AF_INET6 case to the AF_INET case to turn on all the AF_INET options too in
the AF_INET6 case.
Fixes: f2aeed3a59 ("rxrpc: Fix error reception on AF_INET6 sockets")
Signed-off-by: David Howells <dhowells@redhat.com>
Make the following changes to improve the robustness of the code that sets
up a new service call:
(1) Cache the rxrpc_sock struct obtained in rxrpc_data_ready() to do a
service ID check and pass that along to rxrpc_new_incoming_call().
This means that I can remove the check from rxrpc_new_incoming_call()
without the need to worry about the socket attached to the local
endpoint getting replaced - which would invalidate the check.
(2) Cache the rxrpc_peer struct, thereby allowing the peer search to be
done once. The peer is passed to rxrpc_new_incoming_call(), thereby
saving the need to repeat the search.
This also reduces the possibility of rxrpc_publish_service_conn()
BUG()'ing due to the detection of a duplicate connection, despite the
initial search done by rxrpc_find_connection_rcu() having turned up
nothing.
This BUG() shouldn't ever get hit since rxrpc_data_ready() *should* be
non-reentrant and the result of the initial search should still hold
true, but it has proven possible to hit.
I *think* this may be due to __rxrpc_lookup_peer_rcu() cutting short
the iteration over the hash table if it finds a matching peer with a
zero usage count, but I don't know for sure since it's only ever been
hit once that I know of.
Another possibility is that a bug in rxrpc_data_ready() that checked
the wrong byte in the header for the RXRPC_CLIENT_INITIATED flag
might've let through a packet that caused a spurious and invalid call
to be set up. That is addressed in another patch.
(3) Fix __rxrpc_lookup_peer_rcu() to skip peer records that have a zero
usage count rather than stopping and returning not found, just in case
there's another peer record behind it in the bucket.
(4) Don't search the peer records in rxrpc_alloc_incoming_call(), but
rather either use the peer cached in (2) or, if one wasn't found,
preemptively install a new one.
Fixes: 8496af50eb ("rxrpc: Use RCU to access a peer's service connection tree")
Signed-off-by: David Howells <dhowells@redhat.com>
Do more up-front checking on incoming packets to weed out invalid ones and
also ones aimed at services that we don't support.
Whilst we're at it, replace the clearing of call and skew if we don't find
a connection with just initialising the variables to zero at the top of the
function.
Signed-off-by: David Howells <dhowells@redhat.com>
In the input path, a received sk_buff can be marked for rejection by
setting RXRPC_SKB_MARK_* in skb->mark and, if needed, some auxiliary data
(such as an abort code) in skb->priority. The rejection is handled by
queueing the sk_buff up for dealing with in process context. The output
code reads the mark and priority and, theoretically, generates an
appropriate response packet.
However, if RXRPC_SKB_MARK_BUSY is set, this isn't noticed and an ABORT
message with a random abort code is generated (since skb->priority wasn't
set to anything).
Fix this by outputting the appropriate sort of packet.
Also, whilst we're at it, most of the marks are no longer used, so remove
them and rename the remaining two to something more obvious.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix RTT information gathering in AF_RXRPC by the following means:
(1) Enable Rx timestamping on the transport socket with SO_TIMESTAMPNS.
(2) If the sk_buff doesn't have a timestamp set when rxrpc_data_ready()
collects it, set it at that point.
(3) Allow ACKs to be requested on the last packet of a client call, but
not a service call. We need to be careful lest we undo:
bf7d620abf
Author: David Howells <dhowells@redhat.com>
Date: Thu Oct 6 08:11:51 2016 +0100
rxrpc: Don't request an ACK on the last DATA packet of a call's Tx phase
but that only really applies to service calls that we're handling,
since the client side gets to send the final ACK (or not).
(4) When about to transmit an ACK or DATA packet, record the Tx timestamp
before only; don't update the timestamp afterwards.
(5) Switch the ordering between recording the serial and recording the
timestamp to always set the serial number first. The serial number
shouldn't be seen referenced by an ACK packet until we've transmitted
the packet bearing it - so in the Rx path, we don't need the timestamp
until we've checked the serial number.
Fixes: cf1a6474f8 ("rxrpc: Add per-peer RTT tracker")
Signed-off-by: David Howells <dhowells@redhat.com>
There's a check in rxrpc_data_ready() that's checking the CLIENT_INITIATED
flag in the packet type field rather than in the packet flags field.
Fix this by creating a pair of helper functions to check whether the packet
is going to the client or to the server and use them generally.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
In the quest to remove all stack VLA usage from the kernel[1], this
replaces struct crypto_skcipher and SKCIPHER_REQUEST_ON_STACK() usage
with struct crypto_sync_skcipher and SYNC_SKCIPHER_REQUEST_ON_STACK(),
which uses a fixed stack size.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Cc: David Howells <dhowells@redhat.com>
Cc: linux-afs@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
rxrpc_find_connection_rcu() initialises variable k twice with the same
information. Remove one of the initialisations.
Signed-off-by: David Howells <dhowells@redhat.com>
An SKB is not on a list if skb->next is NULL.
Codify this convention into a helper function and use it
where we are dequeueing an SKB and need to mark it as such.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
Pull locking/atomics update from Thomas Gleixner:
"The locking, atomics and memory model brains delivered:
- A larger update to the atomics code which reworks the ordering
barriers, consolidates the atomic primitives, provides the new
atomic64_fetch_add_unless() primitive and cleans up the include
hell.
- Simplify cmpxchg() instrumentation and add instrumentation for
xchg() and cmpxchg_double().
- Updates to the memory model and documentation"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (48 commits)
locking/atomics: Rework ordering barriers
locking/atomics: Instrument cmpxchg_double*()
locking/atomics: Instrument xchg()
locking/atomics: Simplify cmpxchg() instrumentation
locking/atomics/x86: Reduce arch_cmpxchg64*() instrumentation
tools/memory-model: Rename litmus tests to comply to norm7
tools/memory-model/Documentation: Fix typo, smb->smp
sched/Documentation: Update wake_up() & co. memory-barrier guarantees
locking/spinlock, sched/core: Clarify requirements for smp_mb__after_spinlock()
sched/core: Use smp_mb() in wake_woken_function()
tools/memory-model: Add informal LKMM documentation to MAINTAINERS
locking/atomics/Documentation: Describe atomic_set() as a write operation
tools/memory-model: Make scripts executable
tools/memory-model: Remove ACCESS_ONCE() from model
tools/memory-model: Remove ACCESS_ONCE() from recipes
locking/memory-barriers.txt/kokr: Update Korean translation to fix broken DMA vs. MMIO ordering example
MAINTAINERS: Add Daniel Lustig as an LKMM reviewer
tools/memory-model: Fix ISA2+pooncelock+pooncelock+pombonce name
tools/memory-model: Add litmus test for full multicopy atomicity
locking/refcount: Always allow checked forms
...
The static int 'zero' is defined but is never used hence it is
redundant and can be removed. The use of this variable was removed
with commit a158bdd324 ("rxrpc: Fix call timeouts").
Cleans up clang warning:
warning: 'zero' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF_RXRPC has a keepalive message generator that generates a message for a
peer ~20s after the last transmission to that peer to keep firewall ports
open. The implementation is incorrect in the following ways:
(1) It mixes up ktime_t and time64_t types.
(2) It uses ktime_get_real(), the output of which may jump forward or
backward due to adjustments to the time of day.
(3) If the current time jumps forward too much or jumps backwards, the
generator function will crank the base of the time ring round one slot
at a time (ie. a 1s period) until it catches up, spewing out VERSION
packets as it goes.
Fix the problem by:
(1) Only using time64_t. There's no need for sub-second resolution.
(2) Use ktime_get_seconds() rather than ktime_get_real() so that time
isn't perceived to go backwards.
(3) Simplifying rxrpc_peer_keepalive_worker() by splitting it into two
parts:
(a) The "worker" function that manages the buckets and the timer.
(b) The "dispatch" function that takes the pending peers and
potentially transmits a keepalive packet before putting them back
in the ring into the slot appropriate to the revised last-Tx time.
(4) Taking everything that's pending out of the ring and splicing it into
a temporary collector list for processing.
In the case that there's been a significant jump forward, the ring
gets entirely emptied and then the time base can be warped forward
before the peers are processed.
The warping can't happen if the ring isn't empty because the slot a
peer is in is keepalive-time dependent, relative to the base time.
(5) Limit the number of iterations of the bucket array when scanning it.
(6) Set the timer to skip any empty slots as there's no point waking up if
there's nothing to do yet.
This can be triggered by an incoming call from a server after a reboot with
AF_RXRPC and AFS built into the kernel causing a peer record to be set up
before userspace is started. The system clock is then adjusted by
userspace, thereby potentially causing the keepalive generator to have a
meltdown - which leads to a message like:
watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [kworker/0:1:23]
...
Workqueue: krxrpcd rxrpc_peer_keepalive_worker
EIP: lock_acquire+0x69/0x80
...
Call Trace:
? rxrpc_peer_keepalive_worker+0x5e/0x350
? _raw_spin_lock_bh+0x29/0x60
? rxrpc_peer_keepalive_worker+0x5e/0x350
? rxrpc_peer_keepalive_worker+0x5e/0x350
? __lock_acquire+0x3d3/0x870
? process_one_work+0x110/0x340
? process_one_work+0x166/0x340
? process_one_work+0x110/0x340
? worker_thread+0x39/0x3c0
? kthread+0xdb/0x110
? cancel_delayed_work+0x90/0x90
? kthread_stop+0x70/0x70
? ret_from_fork+0x19/0x24
Fixes: ace45bec6d ("rxrpc: Fix firewall route keepalive")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push iov_iter up from rxrpc_kernel_recv_data() to its caller to allow
non-contiguous iovs to be passed down, thereby permitting file reading to
be simplified in the AFS filesystem in a future patch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of SKCIPHER_REQUEST_ON_STACK() will trigger FRAME_WARN warnings
(when less than 2048) once the VLA is no longer hidden from the check:
net/rxrpc/rxkad.c:398:1: warning: the frame size of 1152 bytes is larger than 1024 bytes [-Wframe-larger-than=]
net/rxrpc/rxkad.c:242:1: warning: the frame size of 1152 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This passes the initial SKCIPHER_REQUEST_ON_STACK allocation to the leaf
functions for reuse. Two requests allocated on the stack is not needed
when only one is used at a time.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/rxrpc/proc.c: In function 'rxrpc_call_seq_show':
net/rxrpc/proc.c:66:29: warning:
variable 'nowj' set but not used [-Wunused-but-set-variable]
unsigned long timeout = 0, nowj;
^
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There just check the user call ID isn't already in use, hence should
compare user_call_ID with xcall->user_call_ID, which is current
node's user_call_ID.
Fixes: 540b1c48c3 ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg")
Suggested-by: David Howells <dhowells@redhat.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Immediately flush any outstanding ACK on entry to rxrpc_recvmsg_data() -
which transfers data to the target buffers - if we previously had an Rx
underrun (ie. we returned -EAGAIN because we ran out of received data).
This lets the server know what we've managed to receive something.
Also flush any outstanding ACK after calling the function if it hit -EAGAIN
to let the server know we processed some data.
It might be better to send more ACKs, possibly on a time-based scheme, but
that needs some more consideration.
With this and some additional AFS patches, it is possible to get large
unencrypted O_DIRECT reads to be almost as fast as NFS over TCP. It looks
like it might be theoretically possible to improve performance yet more for
a server running a single operation as investigation of packet timestamps
indicates that the server keeps stalling.
The issue appears to be that rxrpc runs in to trouble with ACK packets
getting batched together (up to ~32 at a time) somewhere between the IP
transmit queue on the client and the ethernet receive queue on the server.
However, this case isn't too much of a worry as even a lightly loaded
server should be receiving sufficient packet flux to flush the ACK packets
to the UDP socket.
Signed-off-by: David Howells <dhowells@redhat.com>
The final ACK that closes out an rxrpc call needs to be transmitted by the
client unless we're going to follow up with a DATA packet for a new call on
the same channel (which implicitly ACK's the previous call, thereby saving
an ACK).
Currently, we don't do that, so if no follow on call is immediately
forthcoming, the server will resend the last DATA packet - at which point
rxrpc_conn_retransmit_call() will be triggered and will (re)send the final
ACK. But the server has to hold on to the last packet until the ACK is
received, thereby holding up its resources.
Fix the client side to propose a delayed final ACK, to be transmitted after
a short delay, assuming the call isn't superseded by a new one.
Signed-off-by: David Howells <dhowells@redhat.com>
Increase the size of a call's Rx window from 32 to 63 - ie. one less than
the size of the ring buffer. This makes large data transfers perform
better when the Tx window on the other side is around 64 (as is the case
with Auristor's YFS fileserver).
If the server window size is ~32 or smaller, this should make no
difference.
Signed-off-by: David Howells <dhowells@redhat.com>
Trace successful packet transmission (kernel_sendmsg() succeeded, that is)
in AF_RXRPC. We can share the enum that defines the transmission points
with the trace_rxrpc_tx_fail() tracepoint, so rename its constants to be
applicable to both.
Also, save the internal call->debug_id in the rxrpc_channel struct so that
it can be used in retransmission trace lines.
Signed-off-by: David Howells <dhowells@redhat.com>
Show the four current call IDs in /proc/net/rxrpc/conns.
Show the current packet Rx serial number in /proc/net/rxrpc/calls.
Signed-off-by: David Howells <dhowells@redhat.com>
Display in /proc/net/rxrpc/calls the timeout by which a call next expects
to receive a packet.
This makes it easier to debug timeout issues.
Signed-off-by: David Howells <dhowells@redhat.com>
Variables 'sp' and 'did_discard' are being assigned,
but are never used, hence they are redundant and can be removed.
fix following warning:
net/rxrpc/call_event.c:165:25: warning: variable 'sp' set but not used [-Wunused-but-set-variable]
net/rxrpc/conn_client.c:1054:7: warning: variable 'did_discard' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While __atomic_add_unless() was originally intended as a building-block
for atomic_add_unless(), it's now used in a number of places around the
kernel. It's the only common atomic operation named __atomic*(), rather
than atomic_*(), and for consistency it would be better named
atomic_fetch_add_unless().
This lack of consistency is slightly confusing, and gets in the way of
scripting atomics. Given that, let's clean things up and promote it to
an official part of the atomics API, in the form of
atomic_fetch_add_unless().
This patch converts definitions and invocations over to the new name,
including the instrumented version, using the following script:
----
git grep -w __atomic_add_unless | while read line; do
sed -i '{s/\<__atomic_add_unless\>/atomic_fetch_add_unless/}' "${line%%:*}";
done
git grep -w __arch_atomic_add_unless | while read line; do
sed -i '{s/\<__arch_atomic_add_unless\>/arch_atomic_fetch_add_unless/}' "${line%%:*}";
done
----
Note that we do not have atomic{64,_long}_fetch_add_unless(), which will
be introduced by later patches.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/lkml/20180621121321.4761-2-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
When retransmitting the final ACK or ABORT packet for a call, the cid field
in the packet header is set to the connection's cid, but this is incorrect
as it also needs to include the channel number on that connection that the
call was made on.
Fix this by OR'ing in the channel number.
Note that this fixes the bug that:
commit 1a025028d4
rxrpc: Fix handling of call quietly cancelled out on server
works around. I'm not intending to revert that as it will help protect
against problems that might occur on the server.
Fixes: 3136ef49a1 ("rxrpc: Delay terminal ACK transmission on a client call")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
Sometimes an in-progress call will stop responding on the fileserver when
the fileserver quietly cancels the call with an internally marked abort
(RX_CALL_DEAD), without sending an ABORT to the client.
This causes the client's call to eventually expire from lack of incoming
packets directed its way, which currently leads to it being cancelled
locally with ETIME. Note that it's not currently clear as to why this
happens as it's really hard to reproduce.
The rotation policy implement by kAFS, however, doesn't differentiate
between ETIME meaning we didn't get any response from the server and ETIME
meaning the call got cancelled mid-flow. The latter leads to an oops when
fetching data as the rotation partially resets the afs_read descriptor,
which can result in a cleared page pointer being dereferenced because that
page has already been filled.
Handle this by the following means:
(1) Set a flag on a call when we receive a packet for it.
(2) Store the highest packet serial number so far received for a call
(bearing in mind this may wrap).
(3) If, when the "not received anything recently" timeout expires on a
call, we've received at least one packet for a call and the connection
as a whole has received packets more recently than that call, then
cancel the call locally with ECONNRESET rather than ETIME.
This indicates that the call was definitely in progress on the server.
(4) In kAFS, if the rotation algorithm sees ECONNRESET rather than ETIME,
don't try the next server, but rather abort the call.
This avoids the oops as we don't try to reuse the afs_read struct.
Rather, as-yet ungotten pages will be reread at a later data.
Also:
(5) Add an rxrpc tracepoint to log detection of the call being reset.
Without this, I occasionally see an oops like the following:
general protection fault: 0000 [#1] SMP PTI
...
RIP: 0010:_copy_to_iter+0x204/0x310
RSP: 0018:ffff8800cae0f828 EFLAGS: 00010206
RAX: 0000000000000560 RBX: 0000000000000560 RCX: 0000000000000560
RDX: ffff8800cae0f968 RSI: ffff8800d58b3312 RDI: 0005080000000000
RBP: ffff8800cae0f968 R08: 0000000000000560 R09: ffff8800ca00f400
R10: ffff8800c36f28d4 R11: 00000000000008c4 R12: ffff8800cae0f958
R13: 0000000000000560 R14: ffff8800d58b3312 R15: 0000000000000560
FS: 00007fdaef108080(0000) GS:ffff8800ca680000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fb28a8fa000 CR3: 00000000d2a76002 CR4: 00000000001606e0
Call Trace:
skb_copy_datagram_iter+0x14e/0x289
rxrpc_recvmsg_data.isra.0+0x6f3/0xf68
? trace_buffer_unlock_commit_regs+0x4f/0x89
rxrpc_kernel_recv_data+0x149/0x421
afs_extract_data+0x1e0/0x798
? afs_wait_for_call_to_complete+0xc9/0x52e
afs_deliver_fs_fetch_data+0x33a/0x5ab
afs_deliver_to_call+0x1ee/0x5e0
? afs_wait_for_call_to_complete+0xc9/0x52e
afs_wait_for_call_to_complete+0x12b/0x52e
? wake_up_q+0x54/0x54
afs_make_call+0x287/0x462
? afs_fs_fetch_data+0x3e6/0x3ed
? rcu_read_lock_sched_held+0x5d/0x63
afs_fs_fetch_data+0x3e6/0x3ed
afs_fetch_data+0xbb/0x14a
afs_readpages+0x317/0x40d
__do_page_cache_readahead+0x203/0x2ba
? ondemand_readahead+0x3a7/0x3c1
ondemand_readahead+0x3a7/0x3c1
generic_file_buffered_read+0x18b/0x62f
__vfs_read+0xdb/0xfe
vfs_read+0xb2/0x137
ksys_read+0x50/0x8c
do_syscall_64+0x7d/0x1a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Note the weird value in RDI which is a result of trying to kmap() a NULL
page pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variants of proc_create{,_data} that directly take a struct seq_operations
and deal with network namespaces in ->open and ->release. All callers of
proc_create + seq_open_net converted over, and seq_{open,release}_net are
removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix the kernel call initiation to set the minimum security level for kernel
initiated calls (such as from kAFS) from the sockopt value.
Fixes: 19ffa01c9c ("rxrpc: Use structs to hold connection params and protocol info")
Signed-off-by: David Howells <dhowells@redhat.com>
AF_RXRPC tries to turn on IP_RECVERR and IP_MTU_DISCOVER on the UDP socket
it just opened for communications with the outside world, regardless of the
type of socket. Unfortunately, this doesn't work with an AF_INET6 socket.
Fix this by turning on IPV6_RECVERR and IPV6_MTU_DISCOVER instead if the
socket is of the AF_INET6 family.
Without this, kAFS server and address rotation doesn't work correctly
because the algorithm doesn't detect received network errors.
Fixes: 75b54cb57c ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
The expect_rx_by call timeout is supposed to be set when a call is started
to indicate that we need to receive a packet by that point. This is
currently put back every time we receive a packet, but it isn't started
when we first send a packet. Without this, the call may wait forever if
the server doesn't deign to reply.
Fix this by setting the timeout upon a successful UDP sendmsg call for the
first DATA packet. The timeout is initiated only for initial transmission
and not for subsequent retries as we don't want the retry mechanism to
extend the timeout indefinitely.
Fixes: a158bdd324 ("rxrpc: Fix call timeouts")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
By analogy with other Rx implementations, RxRPC packet types 9, 10 and 11
should just be discarded rather than being aborted like other undefined
packet types.
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spinlock
vlan: also check phy_driver ts_info for vlan's real device
Bluetooth: Mark expected switch fall-throughs
Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
Bluetooth: btrsi: remove unused including <linux/version.h>
Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
sh_eth: kill useless check in __sh_eth_get_regs()
sh_eth: add sh_eth_cpu_data::no_xdfar flag
ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
...
When a new client call is requested, an rxrpc_conn_parameters struct object
is passed in with a bunch of parameters set, such as the local endpoint to
use. A pointer to the target peer record is also placed in there by
rxrpc_get_client_conn() - and this is removed if and only if a new
connection object is allocated. Thus it leaks if a new connection object
isn't allocated.
Fix this by putting any peer object attached to the rxrpc_conn_parameters
object in the function that allocated it.
Fixes: 19ffa01c9c ("rxrpc: Use structs to hold connection params and protocol info")
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_local objects cannot be disposed of until all the connections that
point to them have been RCU'd as a connection object holds refcount on the
local endpoint it is communicating through. Currently, this can cause an
assertion failure to occur when a network namespace is destroyed as there's
no check that the RCU destructors for the connections have been run before
we start trying to destroy local endpoints.
The kernel reports:
rxrpc: AF_RXRPC: Leaked local 0000000036a41bc1 {5}
------------[ cut here ]------------
kernel BUG at ../net/rxrpc/local_object.c:439!
Fix this by keeping a count of the live connections and waiting for it to
go to zero at the end of rxrpc_destroy_all_connections().
Fixes: dee46364ce ("rxrpc: Add RCU destruction for connections and calls")
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_call structs don't pin sockets or network namespaces, but may attempt
to access both after their refcount reaches 0 so that they can detach
themselves from the network namespace. However, there's no guarantee that
the socket still exists at this point (so sock_net(&call->socket->sk) may
be invalid) and the namespace may have gone away if the call isn't pinning
a peer.
Fix this by (a) carrying a net pointer in the rxrpc_call struct and (b)
waiting for all calls to be destroyed when the network namespace goes away.
This was detected by checker:
net/rxrpc/call_object.c:634:57: warning: incorrect type in argument 1 (different address spaces)
net/rxrpc/call_object.c:634:57: expected struct sock const *sk
net/rxrpc/call_object.c:634:57: got struct sock [noderef] <asn:4>*<noident>
Fixes: 2baec2c3f8 ("rxrpc: Support network namespacing")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix various issues detected by checker.
Errors:
(*) rxrpc_discard_prealloc() should be using rcu_assign_pointer to set
call->socket.
Warnings:
(*) rxrpc_service_connection_reaper() should be passing NULL rather than 0 to
trace_rxrpc_conn() as the where argument.
(*) rxrpc_disconnect_client_call() should get its net pointer via the
call->conn rather than call->sock to avoid a warning about accessing
an RCU pointer without protection.
(*) Proc seq start/stop functions need annotation as they pass locks
between the functions.
False positives:
(*) Checker doesn't correctly handle of seq-retry lock context balance in
rxrpc_find_service_conn_rcu().
(*) Checker thinks execution may proceed past the BUG() in
rxrpc_publish_service_conn().
(*) Variable length array warnings from SKCIPHER_REQUEST_ON_STACK() in
rxkad.c.
Signed-off-by: David Howells <dhowells@redhat.com>
The rxrpc_security_methods and rxrpc_security_sem user has been removed
in 648af7fca1 ("rxrpc: Absorb the rxkad security module"). This was
noticed by kbuild test robot for the -RT tree but is also true for !RT.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Commit a158bdd3 ("rxrpc: Fix call timeouts") reworked the time calculation
for the next resend event. For this calculation, "oldest" will be before
"now", so ktime_sub(oldest, now) will yield a negative value. When passed
to nsecs_to_jiffies which expects an unsigned value, the end result will be
a very large value, and a resend event scheduled far into the future. This
could cause calls to stall if some packets were lost.
Fix by ordering the arguments to ktime_sub correctly.
Fixes: a158bdd324 ("rxrpc: Fix call timeouts")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
If a call-level abort is received for the previous call to complete on a
connection channel, then that abort is queued for the connection processor
to handle. Unfortunately, the connection processor then assumes without
checking that the abort is connection-level (ie. callNumber is 0) and
distributes it over all active calls on that connection, thereby
incorrectly aborting them.
Fix this by discarding aborts aimed at a completed call.
Further, discard all packets aimed at a call that's complete if there's
currently an active call on a channel, since the DATA packets associated
with the new call automatically terminate the old call.
Fixes: 18bfeba50d ("rxrpc: Perform terminal call ACK/ABORT retransmission from conn processor")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc calls have a ring of packets that are awaiting ACK or retransmission
and a parallel ring of annotations that tracks the state of those packets.
If the initial transmission of a packet on the underlying UDP socket fails
then the packet annotation is marked for resend - but the setting of this
mark accidentally erases the last-packet mark also stored in the same
annotation slot. If this happens, a call won't switch out of the Tx phase
when all the packets have been transmitted.
Fix this by retaining the last-packet mark and only altering the packet
state.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
The rxrpc_reduce_call_timer() function should be passed the 'current time'
in jiffies, not the current ktime time. It's confusing in rxrpc_resend
because that has to deal with both. Pass the correct current time in.
Note that this only affects the trace produced and not the functioning of
the code.
Fixes: a158bdd324 ("rxrpc: Fix call timeouts")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the firewall route keepalive part of AF_RXRPC which is currently
function incorrectly by replying to VERSION REPLY packets from the server
with VERSION REQUEST packets.
Instead, send VERSION REPLY packets to the peers of service connections to
act as keep-alives 20s after the latest packet was transmitted to that
peer.
Also, just discard VERSION REPLY packets rather than replying to them.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a tracepoint to track rxrpc calls moving into the completed state and
to log the completion type and the recorded error value and abort code.
Signed-off-by: David Howells <dhowells@redhat.com>
In rxrpc and afs, use the debug_ids that are monotonically allocated to
various objects as they're allocated rather than pointers as kernel
pointers are now hashed making them less useful. Further, the debug ids
aren't reused anywhere nearly as quickly.
In addition, allow kernel services that use rxrpc, such as afs, to take
numbers from the rxrpc counter, assign them to their own call struct and
pass them in to rxrpc for both client and service calls so that the trace
lines for each will have the same ID tag.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a tracepoint to trace packet resend events and to dump the Tx
annotation buffer for added illumination.
Signed-off-by: David Howells <dhowells@rdhat.com>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations modifies rxrpc_net_id-pointed
per-net entities. There is external link to AF_RXRPC
in fs/afs/Kconfig, but it seems there is no other
pernet_operations interested in that per-net entities.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable 'len' is being initialized with a value that is never
read and it is re-assigned later, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
net/rxrpc/recvmsg.c:275:15: warning: Value stored to 'len' during its
initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the kernel_sendmsg() calls in rxrpc_send_data_packet() need to send
both parts of the iov[] buffer, but one of them does not. Fix it so that
it does.
Without this, short IPv6 rxrpc DATA packets may be seen that have the rxrpc
header included, but no payload.
Fixes: 5a924b8951 ("rxrpc: Don't store the rxrpc header in the Tx queue sk_buffs")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a check recently added to copy_to_user(), it's now not permitted to
copy from slab-held data to userspace unless the slab is whitelisted. This
affects rxrpc_recvmsg() when it attempts to place an RXRPC_USER_CALL_ID
control message in the userspace control message buffer. A warning is
generated by usercopy_warn() because the source is the copy of the
user_call_ID retained in the rxrpc_call struct.
Work around the issue by copying the user_call_ID to a variable on the
stack and passing that to put_cmsg().
The warning generated looks like:
Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLUB object 'dmaengine-unmap-128' (offset 680, size 8)!
WARNING: CPU: 0 PID: 1401 at mm/usercopy.c:81 usercopy_warn+0x7e/0xa0
...
RIP: 0010:usercopy_warn+0x7e/0xa0
...
Call Trace:
__check_object_size+0x9c/0x1a0
put_cmsg+0x98/0x120
rxrpc_recvmsg+0x6fc/0x1010 [rxrpc]
? finish_wait+0x80/0x80
___sys_recvmsg+0xf8/0x240
? __clear_rsb+0x25/0x3d
? __clear_rsb+0x15/0x3d
? __clear_rsb+0x25/0x3d
? __clear_rsb+0x15/0x3d
? __clear_rsb+0x25/0x3d
? __clear_rsb+0x15/0x3d
? __clear_rsb+0x25/0x3d
? __clear_rsb+0x15/0x3d
? finish_task_switch+0xa6/0x2b0
? trace_hardirqs_on_caller+0xed/0x180
? _raw_spin_unlock_irq+0x29/0x40
? __sys_recvmsg+0x4e/0x90
__sys_recvmsg+0x4e/0x90
do_syscall_64+0x7a/0x220
entry_SYSCALL_64_after_hwframe+0x26/0x9b
Reported-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AF_RXRPC is incorrectly sending back to the server any abort it receives
for a client connection. This is due to the final-ACK offload to the
connection event processor patch. The abort code is copied into the
last-call information on the connection channel and then the event
processor is set.
Instead, the following should be done:
(1) In the case of a final-ACK for a successful call, the ACK should be
scheduled as before.
(2) In the case of a locally generated ABORT, the ABORT details should be
cached for sending in response to further packets related to that
call and no further action scheduled at call disconnect time.
(3) In the case of an ACK received from the peer, the call should be
considered dead, no ABORT should be transmitted at this time. In
response to further non-ABORT packets from the peer relating to this
call, an RX_USER_ABORT ABORT should be transmitted.
(4) In the case of a call killed due to network error, an RX_USER_ABORT
ABORT should be cached for transmission in response to further
packets, but no ABORT should be sent at this time.
Fixes: 3136ef49a1 ("rxrpc: Delay terminal ACK transmission on a client call")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rxrpc_release_sock() there may be no rx->local value to access, so we
can't unconditionally follow it to the rxrpc network namespace information
to poke the connection reapers.
Instead, use the socket's namespace pointer to find the namespace.
This unfixed code causes the following static checker warning:
net/rxrpc/af_rxrpc.c:898 rxrpc_release_sock()
error: we previously assumed 'rx->local' could be null (see line 887)
Fixes: 3d18cbb7fd ("rxrpc: Fix conn expiry timers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=cyW0
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20171129' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes
Here are three patches for AF_RXRPC. One removes some whitespace, one
fixes terminal ACK generation and the third makes a couple of places
actually use the timeout value just determined rather than ignoring it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
Values assigned to both variable resend_at and ack_at are overwritten
before they can be used.
The correct fix here is to add 'now' to the previously computed value in
resend_at and ack_at.
Addresses-Coverity-ID: 1462262
Addresses-Coverity-ID: 1462263
Addresses-Coverity-ID: 1462264
Fixes: beb8e5e4f3 ("rxrpc: Express protocol timeouts in terms of RTT")
Link: https://marc.info/?i=17004.1511808959%40warthog.procyon.org.uk
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Repeat terminal ACKs and now terminal ACKs are now generated from the
connection event processor rather from call handling as this allows us to
discard client call structures as soon as possible and free up the channel
for a follow on call.
However, in ACKs so generated, the additional information trailer is
malformed because the padding that's meant to be in the middle isn't
included in what's transmitted.
Fix it so that the 3 bytes of padding are included in the transmission.
Further, the trailer is misaligned because of the padding, so assigment to
the u16 and u32 fields inside it might cause problems on some arches, so
fix this by breaking the padding and the trailer out of the packed struct.
(This also deals with potential compiler weirdies where some of the nested
structs are packed and some aren't).
The symptoms can be seen in wireshark as terminal DUPLICATE or IDLE ACK
packets in which the Max MTU, Interface MTU and rwind fields have weird
values and the Max Packets field is apparently missing.
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the rxrpc connection expiry timers so that connections for closed
AF_RXRPC sockets get deleted in a more timely fashion, freeing up the
transport UDP port much more quickly.
(1) Replace the delayed work items with work items plus timers so that
timer_reduce() can be used to shorten them and so that the timer
doesn't requeue the work item if the net namespace is dead.
(2) Don't use queue_delayed_work() as that won't alter the timeout if the
timer is already running.
(3) Don't rearm the timers if the network namespace is dead.
Signed-off-by: David Howells <dhowells@redhat.com>
RxRPC service endpoints expire like they're supposed to by the following
means:
(1) Mark dead rxrpc_net structs (with ->live) rather than twiddling the
global service conn timeout, otherwise the first rxrpc_net struct to
die will cause connections on all others to expire immediately from
then on.
(2) Mark local service endpoints for which the socket has been closed
(->service_closed) so that the expiration timeout can be much
shortened for service and client connections going through that
endpoint.
(3) rxrpc_put_service_conn() needs to schedule the reaper when the usage
count reaches 1, not 0, as idle conns have a 1 count.
(4) The accumulator for the earliest time we might want to schedule for
should be initialised to jiffies + MAX_JIFFY_OFFSET, not ULONG_MAX as
the comparison functions use signed arithmetic.
(5) Simplify the expiration handling, adding the expiration value to the
idle timestamp each time rather than keeping track of the time in the
past before which the idle timestamp must go to be expired. This is
much easier to read.
(6) Ignore the timeouts if the net namespace is dead.
(7) Restart the service reaper work item rather the client reaper.
Signed-off-by: David Howells <dhowells@redhat.com>
We need to transmit a packet every so often to act as a keepalive for the
peer (which has a timeout from the last time it received a packet) and also
to prevent any intervening firewalls from closing the route.
Do this by resetting a timer every time we transmit a packet. If the timer
ever expires, we transmit a PING ACK packet and thereby also elicit a PING
RESPONSE ACK from the other side - which prevents our last-rx timeout from
expiring.
The timer is set to 1/6 of the last-rx timeout so that we can detect the
other side going away if it misses 6 replies in a row.
This is particularly necessary for servers where the processing of the
service function may take a significant amount of time.
Signed-off-by: David Howells <dhowells@redhat.com>
Add an extra timeout that is set/updated when we send a DATA packet that
has the request-ack flag set. This allows us to detect if we don't get an
ACK in response to the latest flagged packet.
The ACK packet is adjudged to have been lost if it doesn't turn up within
2*RTT of the transmission.
If the timeout occurs, we schedule the sending of a PING ACK to find out
the state of the other side. If a new DATA packet is ready to go sooner,
we cancel the sending of the ping and set the request-ack flag on that
instead.
If we get back a PING-RESPONSE ACK that indicates a lower tx_top than what
we had at the time of the ping transmission, we adjudge all the DATA
packets sent between the response tx_top and the ping-time tx_top to have
been lost and retransmit immediately.
Rather than sending a PING ACK, we could just pick a DATA packet and
speculatively retransmit that with request-ack set. It should result in
either a REQUESTED ACK or a DUPLICATE ACK which we can then use in lieu the
a PING-RESPONSE ACK mentioned above.
Signed-off-by: David Howells <dhowells@redhat.com>
Express protocol timeouts for data retransmission and deferred ack
generation in terms on RTT rather than specified timeouts once we have
sufficient RTT samples.
For the moment, this requires just one RTT sample to be able to use this
for ack deferral and two for data retransmission.
The data retransmission timeout is set at RTT*1.5 and the ACK deferral
timeout is set at RTT.
Note that the calculated timeout is limited to a minimum of 4ns to make
sure it doesn't happen too quickly.
Signed-off-by: David Howells <dhowells@redhat.com>
Don't transmit a DELAY ACK immediately on proposal when the Rx window is
rotated, but rather defer it to the work function. This means that we have
a chance to queue/consume more received packets before we actually send the
DELAY ACK, or even cancel it entirely, thereby reducing the number of
packets transmitted.
We do, however, want to continue sending other types of packet immediately,
particularly REQUESTED ACKs, as they may be used for RTT calculation by the
other side.
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the rxrpc call expiration timeouts and make them settable from
userspace. By analogy with other rx implementations, there should be three
timeouts:
(1) "Normal timeout"
This is set for all calls and is triggered if we haven't received any
packets from the peer in a while. It is measured from the last time
we received any packet on that call. This is not reset by any
connection packets (such as CHALLENGE/RESPONSE packets).
If a service operation takes a long time, the server should generate
PING ACKs at a duration that's substantially less than the normal
timeout so is to keep both sides alive. This is set at 1/6 of normal
timeout.
(2) "Idle timeout"
This is set only for a service call and is triggered if we stop
receiving the DATA packets that comprise the request data. It is
measured from the last time we received a DATA packet.
(3) "Hard timeout"
This can be set for a call and specified the maximum lifetime of that
call. It should not be specified by default. Some operations (such
as volume transfer) take a long time.
Allow userspace to set/change the timeouts on a call with sendmsg, using a
control message:
RXRPC_SET_CALL_TIMEOUTS
The data to the message is a number of 32-bit words, not all of which need
be given:
u32 hard_timeout; /* sec from first packet */
u32 idle_timeout; /* msec from packet Rx */
u32 normal_timeout; /* msec from data Rx */
This can be set in combination with any other sendmsg() that affects a
call.
Signed-off-by: David Howells <dhowells@redhat.com>
When rxrpc_sendmsg() parses the control message buffer, it places the
parameters extracted into a structure, but lumps together call parameters
(such as user call ID) with operation parameters (such as whether to send
data, send an abort or accept a call).
Split the call parameters out into their own structure, a copy of which is
then embedded in the operation parameters struct.
The call parameters struct is then passed down into the places that need it
instead of passing the individual parameters. This allows for extra call
parameters to be added.
Signed-off-by: David Howells <dhowells@redhat.com>
Delay terminal ACK transmission on a client call by deferring it to the
connection processor. This allows it to be skipped if we can send the next
call instead, the first DATA packet of which will implicitly ack this call.
Signed-off-by: David Howells <dhowells@redhat.com>
Don't set upgrade by default when creating a call from sendmsg(). This is
a holdover from when I was testing the code.
Signed-off-by: David Howells <dhowells@redhat.com>
The caller of rxrpc_accept_call() must release the lock on call->user_mutex
returned by that function.
Signed-off-by: David Howells <dhowells@redhat.com>
-----BEGIN PGP SIGNATURE-----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=MYda
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-next-20171111' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes
Here are some patches that fix some things in AF_RXRPC:
(1) Prevent notifications from being passed to a kernel service for a call
that it has ended.
(2) Fix a null pointer deference that occurs under some circumstances when an
ACK is generated.
(3) Fix a number of things to do with call expiration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix call expiry handling in the following ways
(1) If all the request data from a client call is acked, don't send a
follow up IDLE ACK with firstPacket == 1 and previousPacket == 0 as
this appears to fool some servers into thinking everything has been
accepted.
(2) Never send an abort back to the server once it has ACK'd all the
request packets; rather just try to reuse the channel for the next
call. The first request DATA packet of the next call on the same
channel will implicitly ACK the entire reply of the dead call - even
if we haven't transmitted it yet.
(3) Don't send RX_CALL_TIMEOUT in an ABORT packet, librx uses abort codes
to pass local errors to the caller in addition to remote errors, and
this is meant to be local only.
The following also need to be addressed in future patches:
(4) Service calls should send PING ACKs as 'keep alives' if the server is
still processing the call.
(5) VERSION REPLY packets should be sent to the peers of service
connections to act as keep-alives. This is used to keep firewall
routes in place. The AFS CM should enable this.
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_fill_out_ack() needs to be passed the connection pointer from its
caller rather than using call->conn as the call may be disconnected in
parallel with it, clearing call->conn, leading to:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: rxrpc_send_ack_packet+0x231/0x6a4
Signed-off-by: David Howells <dhowells@redhat.com>
Place a spinlock around the invocation of call->notify_rx() for a kernel
service call and lock again when ending the call and replace the
notification pointer with a pointer to a dummy function.
This is required because it's possible for rxrpc_notify_socket() to be
called after the call has been ended by the kernel service if called from
the asynchronous work function rxrpc_process_call().
However, rxrpc_notify_socket() currently only holds the RCU read lock when
invoking ->notify_rx(), which means that the afs_call struct would need to
be disposed of by call_rcu() rather than by kfree().
But we shouldn't see any notifications from a call after calling
rxrpc_kernel_end_call(), so a lock is required in rxrpc code.
Without this, we may see the call wait queue as having a corrupt spinlock:
BUG: spinlock bad magic on CPU#0, kworker/0:2/1612
general protection fault: 0000 [#1] SMP
...
Workqueue: krxrpcd rxrpc_process_call
task: ffff88040b83c400 task.stack: ffff88040adfc000
RIP: 0010:spin_bug+0x161/0x18f
RSP: 0018:ffff88040adffcc0 EFLAGS: 00010002
RAX: 0000000000000032 RBX: 6b6b6b6b6b6b6b6b RCX: ffffffff81ab16cf
RDX: ffff88041fa14c01 RSI: ffff88041fa0ccb8 RDI: ffff88041fa0ccb8
RBP: ffff88040adffcd8 R08: 00000000ffffffff R09: 00000000ffffffff
R10: ffff88040adffc60 R11: 000000000000022c R12: ffff88040aca2208
R13: ffffffff81a58114 R14: 0000000000000000 R15: 0000000000000000
....
Call Trace:
do_raw_spin_lock+0x1d/0x89
_raw_spin_lock_irqsave+0x3d/0x49
? __wake_up_common_lock+0x4c/0xa7
__wake_up_common_lock+0x4c/0xa7
? __lock_is_held+0x47/0x7a
__wake_up+0xe/0x10
afs_wake_up_call_waiter+0x11b/0x122 [kafs]
rxrpc_notify_socket+0x12b/0x258
rxrpc_process_call+0x18e/0x7d0
process_one_work+0x298/0x4de
? rescuer_thread+0x280/0x280
worker_thread+0x1d1/0x2ae
? rescuer_thread+0x280/0x280
kthread+0x12c/0x134
? kthread_create_on_node+0x3a/0x3a
ret_from_fork+0x27/0x40
In this case, note the corrupt data in EBX. The address of the offending
afs_call is in R12, plus the offset to the spinlock.
Signed-off-by: David Howells <dhowells@redhat.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't release call mutex at the end of rxrpc_kernel_begin_call() if the
call pointer actually holds an error value.
Fixes: 540b1c48c3 ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make AF_RXRPC accept MSG_WAITALL as a flag to sendmsg() to tell it to
ignore signals whilst loading up the message queue, provided progress is
being made in emptying the queue at the other side.
Progress is defined as the base of the transmit window having being
advanced within 2 RTT periods. If the period is exceeded with no progress,
sendmsg() will return anyway, indicating how much data has been copied, if
any.
Once the supplied buffer is entirely decanted, the sendmsg() will return.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide a couple of functions to allow cleaner handling of signals in a
kernel service. They are:
(1) rxrpc_kernel_get_rtt()
This allows the kernel service to find out the RTT time for a call, so
as to better judge how large a timeout to employ.
Note, though, that whilst this returns a value in nanoseconds, the
timeouts can only actually be in jiffies.
(2) rxrpc_kernel_check_life()
This returns a number that is updated when ACKs are received from the
peer (notably including PING RESPONSE ACKs which we can elicit by
sending PING ACKs to see if the call still exists on the server).
The caller should compare the numbers of two calls to see if the call
is still alive.
These can be used to provide an extending timeout rather than returning
immediately in the case that a signal occurs that would otherwise abort an
RPC operation. The timeout would be extended if the server is still
responsive and the call is still apparently alive on the server.
For most operations this isn't that necessary - but for FS.StoreData it is:
OpenAFS writes the data to storage as it comes in without making a backup,
so if we immediately abort it when partially complete on a CTRL+C, say, we
have no idea of the state of the file after the abort.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide support for a kernel service to make use of the service upgrade
facility. This involves:
(1) Pass an upgrade request flag to rxrpc_kernel_begin_call().
(2) Make rxrpc_kernel_recv_data() return the call's current service ID so
that the caller can detect service upgrade and see what the service
was upgraded to.
Signed-off-by: David Howells <dhowells@redhat.com>
When an RxRPC service packet comes in, the target connection is looked up
by an rb-tree search under RCU and a read-locked seqlock; the seqlock retry
check is, however, currently skipped if we got a match, but probably
shouldn't be in case the connection we found gets replaced whilst we're
doing a search.
Make the lookup procedure always go through need_seqretry(), even if the
lookup was successful. This makes sure we always pick up on a write-lock
event.
On the other hand, since we don't take a ref on the object, but rely on RCU
to prevent its destruction after dropping the seqlock, I'm not sure this is
necessary.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a client call that failed on network error to be retried, provided
that the Tx queue still holds DATA packet 1. This allows an operation to
be submitted to another server or another address for the same server
without having to repackage and re-encrypt the data so far processed.
Two new functions are provided:
(1) rxrpc_kernel_check_call() - This is used to find out the completion
state of a call to guess whether it can be retried and whether it
should be retried.
(2) rxrpc_kernel_retry_call() - Disconnect the call from its current
connection, reset the state and submit it as a new client call to a
new address. The new address need not match the previous address.
A call may be retried even if all the data hasn't been loaded into it yet;
a partially constructed will be retained at the same point it was at when
an error condition was detected. msg_data_left() can be used to find out
how much data was packaged before the error occurred.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a callback to rxrpc_kernel_send_data() so that a kernel service can get
a notification that the AF_RXRPC call has transitioned out the Tx phase and
is now waiting for a reply or a final ACK.
This is called from AF_RXRPC with the call state lock held so the
notification is guaranteed to come before any reply is passed back.
Further, modify the AFS filesystem to make use of this so that we don't have
to change the afs_call state before sending the last bit of data.
Signed-off-by: David Howells <dhowells@redhat.com>
call->error is stored as 0 or a negative error code. Don't negate this
value (ie. make it positive) before returning it from a kernel function
(though it should still be negated before passing to userspace through a
control message).
Signed-off-by: David Howells <dhowells@redhat.com>
Fix IPv6 support in AF_RXRPC in the following ways:
(1) When extracting the address from a received IPv4 packet, if the local
transport socket is open for IPv6 then fill out the sockaddr_rxrpc
struct for an IPv4-mapped-to-IPv6 AF_INET6 transport address instead
of an AF_INET one.
(2) When sending CHALLENGE or RESPONSE packets, the transport length needs
to be set from the sockaddr_rxrpc::transport_len field rather than
sizeof() on the IPv4 transport address.
(3) When processing an IPv4 ICMP packet received by an IPv6 socket, set up
the address correctly before searching for the affected peer.
Signed-off-by: David Howells <dhowells@redhat.com>
When an XDR-encoded Kerberos 5 ticket is added as an rxrpc-type key, the
expiry time should be drawn from the k5 part of the token union (which was
what was filled in), rather than the kad part of the union.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Since the 'expiry' variable of 'struct key_preparsed_payload' has been
changed to 'time64_t' type, which is year 2038 safe on 32bits system.
In net/rxrpc subsystem, we need convert 'u32' type to 'time64_t' type
when copying ticket expires time to 'prep->expiry', then this patch
introduces two helper functions to help convert 'u32' to 'time64_t'
type.
This patch also uses ktime_get_real_seconds() to get current time instead
of get_seconds() which is not year 2038 safe on 32bits system.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: David Howells <dhowells@redhat.com>
rxrpc_service_prealloc_one() doesn't set the socket pointer on any new call
it preallocates, but does add it to the rxrpc net namespace call list.
This, however, causes rxrpc_put_call() to oops when the call is discarded
when the socket is closed. rxrpc_put_call() needs the socket to be able to
reach the namespace so that it can use a lock held therein.
Fix this by setting a call's socket pointer immediately before discarding
it.
This can be triggered by unloading the kafs module, resulting in an oops
like the following:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: rxrpc_put_call+0x1e2/0x32d
PGD 0
P4D 0
Oops: 0000 [#1] SMP
Modules linked in: kafs(E-)
CPU: 3 PID: 3037 Comm: rmmod Tainted: G E 4.12.0-fscache+ #213
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
task: ffff8803fc92e2c0 task.stack: ffff8803fef74000
RIP: 0010:rxrpc_put_call+0x1e2/0x32d
RSP: 0018:ffff8803fef77e08 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8803fab99ac0 RCX: 000000000000000f
RDX: ffffffff81c50a40 RSI: 000000000000000c RDI: ffff8803fc92ea88
RBP: ffff8803fef77e30 R08: ffff8803fc87b941 R09: ffffffff82946d20
R10: ffff8803fef77d10 R11: 00000000000076fc R12: 0000000000000005
R13: ffff8803fab99c20 R14: 0000000000000001 R15: ffffffff816c6aee
FS: 00007f915a059700(0000) GS:ffff88041fb80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000030 CR3: 00000003fef39000 CR4: 00000000001406e0
Call Trace:
rxrpc_discard_prealloc+0x325/0x341
rxrpc_listen+0xf9/0x146
kernel_listen+0xb/0xd
afs_close_socket+0x3e/0x173 [kafs]
afs_exit+0x1f/0x57 [kafs]
SyS_delete_module+0x10f/0x19a
do_syscall_64+0x8a/0x149
entry_SYSCALL64_slow_path+0x25/0x25
Fixes: 2baec2c3f8 ("rxrpc: Support network namespacing")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the protocol description header file into net/rxrpc/ and rename it to
protocol.h. It's no longer necessary to expose it as packets are no longer
exposed to kernel services (such as AFS) that use the facility.
The abort codes are transferred to the UAPI header instead as we pass these
back to userspace and also to kernel services.
Signed-off-by: David Howells <dhowells@redhat.com>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
This patch uses refcount_inc_not_zero() instead of
atomic_inc_not_zero_hint() due to absense of a _hint()
version of refcount API. If the hint() version must
be used, we might need to revisit API.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
