[ Upstream commit 7fcc17d0cb12938d2b3507973a6f93fc9ed2c7a1 ]
The Energy Model (EM) provides useful information about device power in
each performance state to other subsystems like: Energy Aware Scheduler
(EAS). The energy calculation in EAS does arithmetic operation based on
the EM em_cpu_energy(). Current implementation of that function uses
em_perf_state::cost as a pre-computed cost coefficient equal to:
cost = power * max_frequency / frequency.
The 'power' is expressed in milli-Watts (or in abstract scale).
There are corner cases when the EAS energy calculation for two Performance
Domains (PDs) return the same value. The EAS compares these values to
choose smaller one. It might happen that this values are equal due to
rounding error. In such scenario, we need better resolution, e.g. 1000
times better. To provide this possibility increase the resolution in the
em_perf_state::cost for 64-bit architectures. The cost of increasing
resolution on 32-bit is pretty high (64-bit division) and is not justified
since there are no new 32bit big.LITTLE EAS systems expected which would
benefit from this higher resolution.
This patch allows to avoid the rounding to milli-Watt errors, which might
occur in EAS energy estimation for each PD. The rounding error is common
for small tasks which have small utilization value.
There are two places in the code where it makes a difference:
1. In the find_energy_efficient_cpu() where we are searching for
best_delta. We might suffer there when two PDs return the same result,
like in the example below.
Scenario:
Low utilized system e.g. ~200 sum_util for PD0 and ~220 for PD1. There
are quite a few small tasks ~10-15 util. These tasks would suffer for
the rounding error. These utilization values are typical when running games
on Android. One of our partners has reported 5..10mA less battery drain
when running with increased resolution.
Some details:
We have two PDs: PD0 (big) and PD1 (little)
Let's compare w/o patch set ('old') and w/ patch set ('new')
We are comparing energy w/ task and w/o task placed in the PDs
a) 'old' w/o patch set, PD0
task_util = 13
cost = 480
sum_util_w/o_task = 215
sum_util_w_task = 228
scale_cpu = 1024
energy_w/o_task = 480 * 215 / 1024 = 100.78 => 100
energy_w_task = 480 * 228 / 1024 = 106.87 => 106
energy_diff = 106 - 100 = 6
(this is equal to 'old' PD1's energy_diff in 'c)')
b) 'new' w/ patch set, PD0
task_util = 13
cost = 480 * 1000 = 480000
sum_util_w/o_task = 215
sum_util_w_task = 228
energy_w/o_task = 480000 * 215 / 1024 = 100781
energy_w_task = 480000 * 228 / 1024 = 106875
energy_diff = 106875 - 100781 = 6094
(this is not equal to 'new' PD1's energy_diff in 'd)')
c) 'old' w/o patch set, PD1
task_util = 13
cost = 160
sum_util_w/o_task = 283
sum_util_w_task = 293
scale_cpu = 355
energy_w/o_task = 160 * 283 / 355 = 127.55 => 127
energy_w_task = 160 * 296 / 355 = 133.41 => 133
energy_diff = 133 - 127 = 6
(this is equal to 'old' PD0's energy_diff in 'a)')
d) 'new' w/ patch set, PD1
task_util = 13
cost = 160 * 1000 = 160000
sum_util_w/o_task = 283
sum_util_w_task = 293
scale_cpu = 355
energy_w/o_task = 160000 * 283 / 355 = 127549
energy_w_task = 160000 * 296 / 355 = 133408
energy_diff = 133408 - 127549 = 5859
(this is not equal to 'new' PD0's energy_diff in 'b)')
2. Difference in the 6% energy margin filter at the end of
find_energy_efficient_cpu(). With this patch the margin comparison also
has better resolution, so it's possible to have better task placement
thanks to that.
Fixes: 27871f7a8a ("PM: Introduce an Energy Model management framework")
Reported-by: CCJ Yeh <CCj.Yeh@mediatek.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb9d62b27ab1e07d625591549c314b7d406d21df ]
The debugfs directory '/sys/kernel/debug/energy_model' is needed before
the Energy Model registration can happen. With the recent change in
debugfs subsystem it's not allowed to create this directory at early
stage (core_initcall). Thus creating this directory would fail.
Postpone the creation of the EM debug dir to later stage: fs_initcall.
It should be safe since all clients: CPUFreq drivers, Devfreq drivers
will be initialized in later stages.
The custom debug log below prints the time of creation the EM debug dir
at fs_initcall and successful registration of EMs at later stages.
[ 1.505717] energy_model: creating rootdir
[ 3.698307] cpu cpu0: EM: created perf domain
[ 3.709022] cpu cpu1: EM: created perf domain
Fixes: 56348560d495 ("debugfs: do not attempt to create a new file before the filesystem is initalized")
Reported-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fef9c8d28e28a808274a18fbd8cc2685817fd62a upstream.
Flush the swap writer after, not before, marking the files, to ensure the
signature is properly written.
Fixes: 6f612af578 ("PM / Hibernate: Group swap ops")
Signed-off-by: Laurent Badel <laurentbadel@eaton.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 428805c0c5e76ef643b1fbc893edfb636b3d8aef ]
get_gendisk grabs a reference on the disk and file operation, so this
code will leak both of them while having absolutely no use for the
gendisk itself.
This effectively reverts commit 2df83fa4bc ("PM / Hibernate: Use
get_gendisk to verify partition if resume_file is integer format")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2351f8d295ed63393190e39c2f7c1fee1a80578f upstream.
Currently the kernel threads are not frozen in software_resume(), so
between dpm_suspend_start(PMSG_QUIESCE) and resume_target_kernel(),
system_freezable_power_efficient_wq can still try to submit SCSI
commands and this can cause a panic since the low level SCSI driver
(e.g. hv_storvsc) has quiesced the SCSI adapter and can not accept
any SCSI commands: https://lkml.org/lkml/2020/4/10/47
At first I posted a fix (https://lkml.org/lkml/2020/4/21/1318) trying
to resolve the issue from hv_storvsc, but with the help of
Bart Van Assche, I realized it's better to fix software_resume(),
since this looks like a generic issue, not only pertaining to SCSI.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3728b50cd9be7d4b1469447cdf1feb93e3b7adb upstream.
It is theoretically possible for the ACPI EC GPE to be set after the
s2idle_ops->wake() called from s2idle_loop() has returned and before
the subsequent pm_wakeup_pending() check is carried out. If that
happens, the resulting wakeup event will cause the system to resume
even though it may be a spurious one.
To avoid that race, first make the ->wake() callback in struct
platform_s2idle_ops return a bool value indicating whether or not
to let the system resume and rearrange s2idle_loop() to use that
value instad of the direct pm_wakeup_pending() call if ->wake() is
present.
Next, rework acpi_s2idle_wake() to process EC events and check
pm_wakeup_pending() before re-arming the SCI for system wakeup
to prevent it from triggering prematurely and add comments to
that function to explain the rationale for the new code flow.
Fixes: 56b9918490 ("PM: sleep: Simplify suspend-to-idle control flow")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18451f9f9e5810b8bd1245c5ae166f257e0e2b9d upstream.
Upon resuming from hibernation, free pages may contain stale data from
the kernel that initiated the resume. This breaks the invariant
inflicted by init_on_free=1 that freed pages must be zeroed.
To deal with this problem, make clear_free_pages() also clear the free
pages when init_on_free is enabled.
Fixes: 6471384af2 ("mm: security: introduce init_on_alloc=1 and init_on_free=1 boot options")
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Alexander Potapenko <glider@google.com>
Cc: 5.3+ <stable@vger.kernel.org> # 5.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da6043fe85eb5ec621e34a92540735dcebbea134 ]
When looking for a bit by number we make use of the cached result from the
preceding lookup to speed up operation. Firstly we check if the requested
pfn is within the cached zone and if not lookup the new zone. We then
check if the offset for that pfn falls within the existing cached node.
This happens regardless of whether the node is within the zone we are
now scanning. With certain memory layouts it is possible for this to
false trigger creating a temporary alias for the pfn to a different bit.
This leads the hibernation code to free memory which it was never allocated
with the expected fallout.
Ensure the zone we are scanning matches the cached zone before considering
the cached node.
Deep thanks go to Andrea for many, many, many hours of hacking and testing
that went into cornering this bug.
Reported-by: Andrea Righi <andrea.righi@canonical.com>
Tested-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Switching cpufreq drivers (or switching operation modes of the
intel_pstate driver from "active" to "passive" and vice versa)
does not work on some x86 systems with ACPI after commit
3000ce3c52 ("cpufreq: Use per-policy frequency QoS"), because
the ACPI _PPC and thermal code uses the same frequency QoS request
object for a given CPU every time a cpufreq driver is registered
and freq_qos_remove_request() does not invalidate the request after
removing it from its QoS list, so freq_qos_add_request() complains
and fails when that request is passed to it again.
Fix the issue by modifying freq_qos_remove_request() to clear the qos
and type fields of the frequency request pointed to by its argument
after removing it from its QoS list so as to invalidate it.
Fixes: 3000ce3c52 ("cpufreq: Use per-policy frequency QoS")
Reported-and-tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Introduce frequency QoS, based on the "raw" low-level PM QoS, to
represent min and max frequency requests and aggregate constraints.
The min and max frequency requests are to be represented by
struct freq_qos_request objects and the aggregate constraints are to
be represented by struct freq_constraints objects. The latter are
expected to be initialized with the help of freq_constraints_init().
The freq_qos_read_value() helper is defined to retrieve the aggregate
constraints values from a given struct freq_constraints object and
there are the freq_qos_add_request(), freq_qos_update_request() and
freq_qos_remove_request() helpers to manipulate the min and max
frequency requests. It is assumed that the the helpers will not
run concurrently with each other for the same struct freq_qos_request
object, so if that may be the case, their uses must ensure proper
synchronization between them (e.g. through locking).
In addition, freq_qos_add_notifier() and freq_qos_remove_notifier()
are provided to add and remove notifiers that will trigger on aggregate
constraint changes to and from a given struct freq_constraints object,
respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Include the <linux/runtime_pm.h> for the definition of
pm_wq to avoid the following warning:
kernel/power/main.c:890:25: warning: symbol 'pm_wq' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull kernel lockdown mode from James Morris:
"This is the latest iteration of the kernel lockdown patchset, from
Matthew Garrett, David Howells and others.
From the original description:
This patchset introduces an optional kernel lockdown feature,
intended to strengthen the boundary between UID 0 and the kernel.
When enabled, various pieces of kernel functionality are restricted.
Applications that rely on low-level access to either hardware or the
kernel may cease working as a result - therefore this should not be
enabled without appropriate evaluation beforehand.
The majority of mainstream distributions have been carrying variants
of this patchset for many years now, so there's value in providing a
doesn't meet every distribution requirement, but gets us much closer
to not requiring external patches.
There are two major changes since this was last proposed for mainline:
- Separating lockdown from EFI secure boot. Background discussion is
covered here: https://lwn.net/Articles/751061/
- Implementation as an LSM, with a default stackable lockdown LSM
module. This allows the lockdown feature to be policy-driven,
rather than encoding an implicit policy within the mechanism.
The new locked_down LSM hook is provided to allow LSMs to make a
policy decision around whether kernel functionality that would allow
tampering with or examining the runtime state of the kernel should be
permitted.
The included lockdown LSM provides an implementation with a simple
policy intended for general purpose use. This policy provides a coarse
level of granularity, controllable via the kernel command line:
lockdown={integrity|confidentiality}
Enable the kernel lockdown feature. If set to integrity, kernel features
that allow userland to modify the running kernel are disabled. If set to
confidentiality, kernel features that allow userland to extract
confidential information from the kernel are also disabled.
This may also be controlled via /sys/kernel/security/lockdown and
overriden by kernel configuration.
New or existing LSMs may implement finer-grained controls of the
lockdown features. Refer to the lockdown_reason documentation in
include/linux/security.h for details.
The lockdown feature has had signficant design feedback and review
across many subsystems. This code has been in linux-next for some
weeks, with a few fixes applied along the way.
Stephen Rothwell noted that commit 9d1f8be5cf ("bpf: Restrict bpf
when kernel lockdown is in confidentiality mode") is missing a
Signed-off-by from its author. Matthew responded that he is providing
this under category (c) of the DCO"
* 'next-lockdown' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (31 commits)
kexec: Fix file verification on S390
security: constify some arrays in lockdown LSM
lockdown: Print current->comm in restriction messages
efi: Restrict efivar_ssdt_load when the kernel is locked down
tracefs: Restrict tracefs when the kernel is locked down
debugfs: Restrict debugfs when the kernel is locked down
kexec: Allow kexec_file() with appropriate IMA policy when locked down
lockdown: Lock down perf when in confidentiality mode
bpf: Restrict bpf when kernel lockdown is in confidentiality mode
lockdown: Lock down tracing and perf kprobes when in confidentiality mode
lockdown: Lock down /proc/kcore
x86/mmiotrace: Lock down the testmmiotrace module
lockdown: Lock down module params that specify hardware parameters (eg. ioport)
lockdown: Lock down TIOCSSERIAL
lockdown: Prohibit PCMCIA CIS storage when the kernel is locked down
acpi: Disable ACPI table override if the kernel is locked down
acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
ACPI: Limit access to custom_method when the kernel is locked down
x86/msr: Restrict MSR access when the kernel is locked down
x86: Lock down IO port access when the kernel is locked down
...
* pm-opp:
PM / OPP: Correct Documentation about library location
opp: of: Support multiple suspend OPPs defined in DT
dt-bindings: opp: Support multiple opp-suspend properties
opp: core: add regulators enable and disable
opp: Don't decrement uninitialized list_kref
* pm-qos:
PM: QoS: Get rid of unused flags
* acpi-pm:
ACPI: PM: Print debug messages on device power state changes
* pm-domains:
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
PM / Domains: Align in-parameter names for some genpd functions
* pm-tools:
pm-graph: make setVal unbuffered again for python2 and python3
cpupower: update German translation
tools/power/cpupower: fix 64bit detection when cross-compiling
cpupower: Add missing newline at end of file
pm-graph v5.5
* pm-s2idle-rework: (21 commits)
ACPI: PM: s2idle: Always set up EC GPE for system wakeup
ACPI: PM: s2idle: Avoid rearming SCI for wakeup unnecessarily
PM: suspend: Fix platform_suspend_prepare_noirq()
intel-hid: Disable button array during suspend-to-idle
intel-hid: intel-vbtn: Avoid leaking wakeup_mode set
ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices
ACPI: EC: PM: Make acpi_ec_dispatch_gpe() print debug message
ACPI: EC: PM: Consolidate some code depending on PM_SLEEP
ACPI: PM: s2idle: Eliminate acpi_sleep_no_ec_events()
ACPI: PM: s2idle: Switch EC over to polling during "noirq" suspend
ACPI: PM: s2idle: Add acpi.sleep_no_lps0 module parameter
ACPI: PM: s2idle: Rearrange lps0_device_attach()
ACPI: PM: Set up EC GPE for system wakeup from drivers that need it
PM: sleep: Drop dpm_noirq_begin() and dpm_noirq_end()
PM: sleep: Integrate suspend-to-idle with generig suspend flow
PM: sleep: Simplify suspend-to-idle control flow
ACPI: PM: Set s2idle_wakeup earlier and clear it later
PM: sleep: Fix possible overflow in pm_system_cancel_wakeup()
ACPI: EC: Return bool from acpi_ec_dispatch_gpe()
ACPICA: Return u32 from acpi_dispatch_gpe()
...
The network_latency and network_throughput flags for PM-QoS have not
found much use in drivers or in userspace since they were introduced.
Commit 4a733ef1be ("mac80211: remove PM-QoS listener") removed the
only user PM_QOS_NETWORK_LATENCY in the kernel a while ago and there
don't seem to be any userspace tools using the character device files
either.
PM_QOS_MEMORY_BANDWIDTH was never even added to the trace events.
Remove all the flags except cpu_dma_latency.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add an ID and a device pointer to 'struct wakeup_source'. Use them to to
expose wakeup sources statistics in sysfs under
/sys/class/wakeup/wakeup<ID>/*.
Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tri Vo <trong@android.com>
Tested-by: Kalesh Singh <kaleshsingh@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
kernel/power/wakelock.c duplicates wakeup source creation and
registration code from drivers/base/power/wakeup.c.
Change struct wakelock's wakeup source to a pointer and use
wakeup_source_register() function to create and register said wakeup
source. Use wakeup_source_unregister() on cleanup path.
Signed-off-by: Tri Vo <trong@android.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is currently no way to verify the resume image when returning
from hibernate. This might compromise the signed modules trust model,
so until we can work with signed hibernate images we disable it when the
kernel is locked down.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Garrett <mjg59@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: rjw@rjwysocki.net
Cc: pavel@ucw.cz
cc: linux-pm@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Use str_has_prefix() instead of strncmp() which is less
straightforward in decode_state().
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit ac9eafbe93 ("ACPI: PM: s2idle: Execute LPS0 _DSM
functions with suspended devices"), a NULL pointer may be dereferenced
if suspend-to-idle is attempted on a platform without "traditional"
suspend support due to invalid fall-through in
platform_suspend_prepare_noirq().
Fix that and while at it add missing braces in platform_resume_noirq().
Fixes: ac9eafbe93 ("ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to Section 3.5 of the "Intel Low Power S0 Idle" document [1],
Function 5 of the LPS0 _DSM is expected to be invoked when the system
configuration matches the criteria for entering the target low-power
state of the platform. In particular, this means that all devices
should be suspended and in low-power states already when that function
is invoked.
This is not the case currently, however, because Function 5 of the
LPS0 _DSM is invoked by it before the "noirq" phase of device suspend,
which means that some devices may not have been put into low-power
states yet at that point. That is a consequence of the previous
design of the suspend-to-idle flow that allowed the "noirq" phase of
device suspend and the "noirq" phase of device resume to be carried
out for multiple times while "suspended" (if any spurious wakeup
events were detected) and the point of the LPS0 _DSM Function 5
invocation was chosen so as to call it (and LPS0 _DSM Function 6
analogously) once per suspend-resume cycle (regardless of how many
times the "noirq" phases of device suspend and resume were carried
out while "suspended").
Now that the suspend-to-idle flow has been redesigned to carry out
the "noirq" phases of device suspend and resume once in each cycle,
the code can be reordered to follow the specification that it is
based on more closely.
For this purpose, add ->prepare_late and ->restore_early platform
callbacks for suspend-to-idle, to be executed, respectively, after
the "noirq" phase of suspending devices and before the "noirq"
phase of resuming them and make ACPI use them for the invocation
of LPS0 _DSM functions as appropriate.
While at it, move the LPS0 entry requirements check to be made
before invoking Functions 3 and 5 of the LPS0 _DSM (also once
per cycle) as follows from the specification [1].
Link: https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf # [1]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Userspace can get suspend stats from the suspend stats debugfs node.
Since debugfs doesn't have stable ABI, expose suspend stats in
sysfs under /sys/power/suspend_stats.
Signed-off-by: Kalesh Singh <kaleshsingh@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After previous changes the suspend-to-idle code flow can be
integrated more tightly with the generic system suspend code flow
by making suspend_enter() call s2idle_loop() later and removing
the direct invocations of dpm_noirq_begin(),
dpm_noirq_suspend_devices(), dpm_noirq_end(), and
dpm_noirq_resume_devices() from the latter, so do that.
This change is not expected to alter functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
After commit 33e4f80ee6 ("ACPI / PM: Ignore spurious SCI wakeups
from suspend-to-idle") the "noirq" phases of device suspend and
resume may run for multiple times during suspend-to-idle, if there
are spurious system wakeup events while suspended. However, this
is complicated and fragile and actually unnecessary.
The main reason for doing this is that on some systems the EC may
signal system wakeup events (power button events, for example) as
well as events that should not cause the system to resume (spurious
system wakeup events). Thus, in order to determine whether or not
a given event signaled by the EC while suspended is a proper system
wakeup one, the EC GPE needs to be dispatched and to start with that
was achieved by allowing the ACPI SCI action handler to run, which
was only possible after calling resume_device_irqs().
However, dispatching the EC GPE this way turned out to take too much
time in some cases and some EC events might be missed due to that, so
commit 68e2201185 ("ACPI: EC: Dispatch the EC GPE directly on
s2idle wake") started to dispatch the EC GPE right after a wakeup
event has been detected, so in fact the full ACPI SCI action handler
doesn't need to run any more to deal with the wakeups coming from the
EC.
Use this observation to simplify the suspend-to-idle control flow
so that the "noirq" phases of device suspend and resume are each
run only once in every suspend-to-idle cycle, which is reported to
significantly reduce power drawn by some systems when suspended to
idle (by allowing them to reach a deep platform-wide low-power state
through the suspend-to-idle flow). [What appears to happen is that
the "noirq" resume of devices after a spurious EC wakeup brings some
devices into a state in which they prevent the platform from reaching
the deep low-power state going forward, even after a subsequent
"noirq" suspend phase, and on some systems the EC triggers such
wakeups already when the "noirq" suspend of devices is running for
the first time in the given suspend/resume cycle, so the platform
cannot reach the deep low-power state at all.]
First, make acpi_s2idle_wake() use the acpi_ec_dispatch_gpe() return
value to determine whether or not the wakeup may have been triggered
by the EC (in which case the system wakeup is canceled and ACPI
events are processed in order to determine whether or not the event
is a proper system wakeup one) and use rearm_wake_irq() (introduced
by a previous change) in it to rearm the ACPI SCI for system wakeup
detection in case the system will remain suspended.
Second, drop acpi_s2idle_sync(), which is not needed any more, and
the corresponding global platform suspend-to-idle callback.
Next, drop the pm_wakeup_pending() check (which is an optimization
only) from __device_suspend_noirq() to prevent it from returning
errors on system wakeups occurring before the "noirq" phase of
device suspend is complete (as in the case of suspend-to-idle it is
not known whether or not these wakeups are suprious at that point),
in order to avoid having to carry out a "noirq" resume of devices
on a spurious system wakeup.
Finally, change the code flow in s2idle_loop() to (1) run the
"noirq" suspend of devices once before starting the loop, (2) check
for spurious EC wakeups (via the platform ->wake callback) for the
first time before calling s2idle_enter(), and (3) run the "noirq"
resume of devices once after leaving the loop.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
- Improve the handling of shared ACPI power resources in the PCI
bus type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec
into account as appropriate and avoid polling devices in D3cold
for PME (Mika Westerberg).
- Fix some corner case issues in ACPI device power management and
in the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210,
and armada-37xx cpufreq drivers (David Arcari, Florian Fainelli,
Paweł Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black).
-----BEGIN PGP SIGNATURE-----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=aBN3
-----END PGP SIGNATURE-----
Merge tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update PCI and ACPI power management (improved handling of ACPI
power resources and PCIe link delays, fixes related to corner cases,
hibernation handling rework), fix and extend the operating performance
points (OPP) framework, add new cpufreq drivers for Raspberry Pi and
imx8m chips, update some other cpufreq drivers, clean up assorted
pieces of PM code and documentation and update tools.
Specifics:
- Improve the handling of shared ACPI power resources in the PCI bus
type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec into
account as appropriate and avoid polling devices in D3cold for PME
(Mika Westerberg).
- Fix some corner case issues in ACPI device power management and in
the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210, and
armada-37xx cpufreq drivers (David Arcari, Florian Fainelli, Paweł
Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black)"
* tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (57 commits)
ACPI: PM: Make acpi_sleep_state_supported() non-static
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Unexport acpi_device_get_power()
Documentation: ABI: power: Add missing newline at end of file
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
cpufreq: Don't skip frequency validation for has_target() drivers
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
cpufreq: Use has_target() instead of !setpolicy
...
Pull scheduler updates from Ingo Molnar:
- Remove the unused per rq load array and all its infrastructure, by
Dietmar Eggemann.
- Add utilization clamping support by Patrick Bellasi. This is a
refinement of the energy aware scheduling framework with support for
boosting of interactive and capping of background workloads: to make
sure critical GUI threads get maximum frequency ASAP, and to make
sure background processing doesn't unnecessarily move to cpufreq
governor to higher frequencies and less energy efficient CPU modes.
- Add the bare minimum of tracepoints required for LISA EAS regression
testing, by Qais Yousef - which allows automated testing of various
power management features, including energy aware scheduling.
- Restructure the former tsk_nr_cpus_allowed() facility that the -rt
kernel used to modify the scheduler's CPU affinity logic such as
migrate_disable() - introduce the task->cpus_ptr value instead of
taking the address of &task->cpus_allowed directly - by Sebastian
Andrzej Siewior.
- Misc optimizations, fixes, cleanups and small enhancements - see the
Git log for details.
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
sched/uclamp: Add uclamp support to energy_compute()
sched/uclamp: Add uclamp_util_with()
sched/cpufreq, sched/uclamp: Add clamps for FAIR and RT tasks
sched/uclamp: Set default clamps for RT tasks
sched/uclamp: Reset uclamp values on RESET_ON_FORK
sched/uclamp: Extend sched_setattr() to support utilization clamping
sched/core: Allow sched_setattr() to use the current policy
sched/uclamp: Add system default clamps
sched/uclamp: Enforce last task's UCLAMP_MAX
sched/uclamp: Add bucket local max tracking
sched/uclamp: Add CPU's clamp buckets refcounting
sched/fair: Rename weighted_cpuload() to cpu_runnable_load()
sched/debug: Export the newly added tracepoints
sched/debug: Add sched_overutilized tracepoint
sched/debug: Add new tracepoint to track PELT at se level
sched/debug: Add new tracepoints to track PELT at rq level
sched/debug: Add a new sched_trace_*() helper functions
sched/autogroup: Make autogroup_path() always available
sched/wait: Deduplicate code with do-while
sched/topology: Remove unused 'sd' parameter from arch_scale_cpu_capacity()
...
* pm-sleep:
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
PM: sleep: Update struct wakeup_source documentation
drivers: base: power: remove wakeup_sources_stats_dentry variable
PM: suspend: Rename pm_suspend_via_s2idle()
PM: sleep: Show how long dpm_suspend_start() and dpm_suspend_end() take
PM: hibernate: powerpc: Expose pfn_is_nosave() prototype
Use zeroing allocator instead of using allocator
followed with memset with 0
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are platforms that do not call pm_set_suspend_via_firmware(),
so pm_suspend_via_firmware() returns 'false' on them, but the power
states of PCI devices (PCIe ports in particular) are changed as a
result of powering down core platform components during system-wide
suspend. Thus the pm_suspend_via_firmware() checks in
pci_pm_suspend_noirq() and pci_pm_resume_noirq() introduced by
commit 3e26c5feed ("PCI: PM: Skip devices in D0 for suspend-to-
idle") are not sufficient to determine that devices left in D0
during suspend will remain in D0 during resume and so the bus-level
power management can be skipped for them.
For this reason, introduce a new global suspend flag,
PM_SUSPEND_FLAG_NO_PLATFORM, set it for suspend-to-idle only
and replace the pm_suspend_via_firmware() checks mentioned above
with checks against this flag.
Fixes: 3e26c5feed ("PCI: PM: Skip devices in D0 for suspend-to-idle")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Based on 1 normalized pattern(s):
this file is released under the gpl v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204655.103854853@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of pm_suspend_via_s2idle() is confusing, as it doesn't
reflect the purpose of the function precisely enough and it is
very similar to pm_suspend_via_firmware(), which has a different
purpose, so rename it as pm_suspend_default_s2idle() and update
its only caller, i8042_register_ports(), accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the PM documents to ReST, in order to allow them to
build with Sphinx.
The conversion is actually:
- add blank lines and indentation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
The declaration for pfn_is_nosave is only available in
kernel/power/power.h. Since this function can be override in arch,
expose it globally. Having a prototype will make sure to avoid warning
(sometime treated as error with W=1) such as:
arch/powerpc/kernel/suspend.c:18:5: error: no previous prototype for 'pfn_is_nosave' [-Werror=missing-prototypes]
This moves the declaration into a globally visible header file and add
missing include to avoid a warning on powerpc.
Also remove the duplicated prototypes since not required anymore.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
sxVEiFZo8ZU9v1IoRb1I
=qU++
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
Based on 1 normalized pattern(s):
this file is released under the gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 68 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.292346262@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As explained in
0cc3cd2165 ("cpu/hotplug: Boot HT siblings at least once")
we always, no matter what, have to bring up x86 HT siblings during boot at
least once in order to avoid first MCE bringing the system to its knees.
That means that whenever 'nosmt' is supplied on the kernel command-line,
all the HT siblings are as a result sitting in mwait or cpudile after
going through the online-offline cycle at least once.
This causes a serious issue though when a kernel, which saw 'nosmt' on its
commandline, is going to perform resume from hibernation: if the resume
from the hibernated image is successful, cr3 is flipped in order to point
to the address space of the kernel that is being resumed, which in turn
means that all the HT siblings are all of a sudden mwaiting on address
which is no longer valid.
That results in triple fault shortly after cr3 is switched, and machine
reboots.
Fix this by always waking up all the SMT siblings before initiating the
'restore from hibernation' process; this guarantees that all the HT
siblings will be properly carried over to the resumed kernel waiting in
resume_play_dead(), and acted upon accordingly afterwards, based on the
target kernel configuration.
Symmetricaly, the resumed kernel has to push the SMT siblings to mwait
again in case it has SMT disabled; this means it has to online all
the siblings when resuming (so that they come out of hlt) and offline
them again to let them reach mwait.
Cc: 4.19+ <stable@vger.kernel.org> # v4.19+
Debugged-by: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0cc3cd2165 ("cpu/hotplug: Boot HT siblings at least once")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add kerneldoc comments to pm_suspend_via_firmware(),
pm_resume_via_firmware() and pm_suspend_via_s2idle()
to explain what they do.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On systems with ACPI platform firmware the last stage of hibernation
is analogous to system suspend to S3 (suspend-to-RAM), so it should
be handled analogously. In particular, pm_suspend_via_firmware()
should return 'true' in that stage to let the callers of it know that
control will be passed to the platform firmware going forward, so
pm_set_suspend_via_firmware() needs to be called then in analogy with
acpi_suspend_begin().
However, the platform hibernation ->begin() callback is invoked
during the "freeze" transition (before creating a snapshot image of
system memory) as well as during the "hibernate" transition which is
the last stage of it and pm_set_suspend_via_firmware() should be
invoked by that callback in the latter stage only.
In order to implement that redefine the hibernation ->begin()
callback to take a pm_message_t argument to indicate which stage
of hibernation is taking place and rework acpi_hibernation_begin()
and acpi_hibernation_begin_old() to take it into account as needed.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix the handling of Performance and Energy Bias Hint (EPB) on
Intel processors and expose it to user space via sysfs to avoid
having to access it through the generic MSR I/F (Rafael Wysocki).
- Improve the handling of global turbo changes made by the platform
firmware in the intel_pstate driver (Rafael Wysocki).
- Convert some slow-path static_cpu_has() callers to boot_cpu_has()
in cpufreq (Borislav Petkov).
- Fix the frequency calculation loop in the armada-37xx cpufreq
driver (Gregory CLEMENT).
- Fix possible object reference leaks in multuple cpufreq drivers
(Wen Yang).
- Fix kerneldoc comment in the centrino cpufreq driver (dongjian).
- Clean up the ACPI and maple cpufreq drivers (Viresh Kumar, Mohan
Kumar).
- Add support for lx2160a and ls1028a to the qoriq cpufreq driver
(Vabhav Sharma, Yuantian Tang).
- Fix kobject memory leak in the cpufreq core (Viresh Kumar).
- Simplify the IOwait boosting in the schedutil cpufreq governor
and rework the TSC cpufreq notifier on x86 (Rafael Wysocki).
- Clean up the cpufreq core and statistics code (Yue Hu, Kyle Lin).
- Improve the cpufreq documentation, add SPDX license tags to
some PM documentation files and unify copyright notices in
them (Rafael Wysocki).
- Add support for "CPU" domains to the generic power domains (genpd)
framework and provide low-level PSCI firmware support for that
feature (Ulf Hansson).
- Rearrange the PSCI firmware support code and add support for
SYSTEM_RESET2 to it (Ulf Hansson, Sudeep Holla).
- Improve genpd support for devices in multiple power domains (Ulf
Hansson).
- Unify target residency for the AFTR and coupled AFTR states in the
exynos cpuidle driver (Marek Szyprowski).
- Introduce new helper routine in the operating performance points
(OPP) framework (Andrew-sh.Cheng).
- Add support for passing on-die termination (ODT) and auto power
down parameters from the kernel to Trusted Firmware-A (TF-A) to
the rk3399_dmc devfreq driver (Enric Balletbo i Serra).
- Add tracing to devfreq (Lukasz Luba).
- Make the exynos-bus devfreq driver suspend all devices on system
shutdown (Marek Szyprowski).
- Fix a few minor issues in the devfreq subsystem and clean it up
somewhat (Enric Balletbo i Serra, MyungJoo Ham, Rob Herring,
Saravana Kannan, Yangtao Li).
- Improve system wakeup diagnostics (Stephen Boyd).
- Rework filesystem sync messages emitted during system suspend and
hibernation (Harry Pan).
-----BEGIN PGP SIGNATURE-----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=nY9p
-----END PGP SIGNATURE-----
Merge tag 'pm-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These fix the (Intel-specific) Performance and Energy Bias Hint (EPB)
handling and expose it to user space via sysfs, fix and clean up
several cpufreq drivers, add support for two new chips to the qoriq
cpufreq driver, fix, simplify and clean up the cpufreq core and the
schedutil governor, add support for "CPU" domains to the generic power
domains (genpd) framework and provide low-level PSCI firmware support
for that feature, fix the exynos cpuidle driver and fix a couple of
issues in the devfreq subsystem and clean it up.
Specifics:
- Fix the handling of Performance and Energy Bias Hint (EPB) on Intel
processors and expose it to user space via sysfs to avoid having to
access it through the generic MSR I/F (Rafael Wysocki).
- Improve the handling of global turbo changes made by the platform
firmware in the intel_pstate driver (Rafael Wysocki).
- Convert some slow-path static_cpu_has() callers to boot_cpu_has()
in cpufreq (Borislav Petkov).
- Fix the frequency calculation loop in the armada-37xx cpufreq
driver (Gregory CLEMENT).
- Fix possible object reference leaks in multuple cpufreq drivers
(Wen Yang).
- Fix kerneldoc comment in the centrino cpufreq driver (dongjian).
- Clean up the ACPI and maple cpufreq drivers (Viresh Kumar, Mohan
Kumar).
- Add support for lx2160a and ls1028a to the qoriq cpufreq driver
(Vabhav Sharma, Yuantian Tang).
- Fix kobject memory leak in the cpufreq core (Viresh Kumar).
- Simplify the IOwait boosting in the schedutil cpufreq governor and
rework the TSC cpufreq notifier on x86 (Rafael Wysocki).
- Clean up the cpufreq core and statistics code (Yue Hu, Kyle Lin).
- Improve the cpufreq documentation, add SPDX license tags to some PM
documentation files and unify copyright notices in them (Rafael
Wysocki).
- Add support for "CPU" domains to the generic power domains (genpd)
framework and provide low-level PSCI firmware support for that
feature (Ulf Hansson).
- Rearrange the PSCI firmware support code and add support for
SYSTEM_RESET2 to it (Ulf Hansson, Sudeep Holla).
- Improve genpd support for devices in multiple power domains (Ulf
Hansson).
- Unify target residency for the AFTR and coupled AFTR states in the
exynos cpuidle driver (Marek Szyprowski).
- Introduce new helper routine in the operating performance points
(OPP) framework (Andrew-sh.Cheng).
- Add support for passing on-die termination (ODT) and auto power
down parameters from the kernel to Trusted Firmware-A (TF-A) to the
rk3399_dmc devfreq driver (Enric Balletbo i Serra).
- Add tracing to devfreq (Lukasz Luba).
- Make the exynos-bus devfreq driver suspend all devices on system
shutdown (Marek Szyprowski).
- Fix a few minor issues in the devfreq subsystem and clean it up
somewhat (Enric Balletbo i Serra, MyungJoo Ham, Rob Herring,
Saravana Kannan, Yangtao Li).
- Improve system wakeup diagnostics (Stephen Boyd).
- Rework filesystem sync messages emitted during system suspend and
hibernation (Harry Pan)"
* tag 'pm-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (72 commits)
cpufreq: Fix kobject memleak
cpufreq: armada-37xx: fix frequency calculation for opp
cpufreq: centrino: Fix centrino_setpolicy() kerneldoc comment
cpufreq: qoriq: add support for lx2160a
x86: tsc: Rework time_cpufreq_notifier()
PM / Domains: Allow to attach a CPU via genpd_dev_pm_attach_by_id|name()
PM / Domains: Search for the CPU device outside the genpd lock
PM / Domains: Drop unused in-parameter to some genpd functions
PM / Domains: Use the base device for driver_deferred_probe_check_state()
cpufreq: qoriq: Add ls1028a chip support
PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain
PM / Domains: Allow OF lookup for multi PM domain case from ->attach_dev()
PM / Domains: Don't kfree() the virtual device in the error path
cpufreq: Move ->get callback check outside of __cpufreq_get()
PM / Domains: remove unnecessary unlikely()
cpufreq: Remove needless bios_limit check in show_bios_limit()
drivers/cpufreq/acpi-cpufreq.c: This fixes the following checkpatch warning
firmware/psci: add support for SYSTEM_RESET2
PM / devfreq: add tracing for scheduling work
trace: events: add devfreq trace event file
...
Pull x86 mm updates from Ingo Molnar:
"The changes in here are:
- text_poke() fixes and an extensive set of executability lockdowns,
to (hopefully) eliminate the last residual circumstances under
which we are using W|X mappings even temporarily on x86 kernels.
This required a broad range of surgery in text patching facilities,
module loading, trampoline handling and other bits.
- tweak page fault messages to be more informative and more
structured.
- remove DISCONTIGMEM support on x86-32 and make SPARSEMEM the
default.
- reduce KASLR granularity on 5-level paging kernels from 512 GB to
1 GB.
- misc other changes and updates"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/mm: Initialize PGD cache during mm initialization
x86/alternatives: Add comment about module removal races
x86/kprobes: Use vmalloc special flag
x86/ftrace: Use vmalloc special flag
bpf: Use vmalloc special flag
modules: Use vmalloc special flag
mm/vmalloc: Add flag for freeing of special permsissions
mm/hibernation: Make hibernation handle unmapped pages
x86/mm/cpa: Add set_direct_map_*() functions
x86/alternatives: Remove the return value of text_poke_*()
x86/jump-label: Remove support for custom text poker
x86/modules: Avoid breaking W^X while loading modules
x86/kprobes: Set instruction page as executable
x86/ftrace: Set trampoline pages as executable
x86/kgdb: Avoid redundant comparison of patched code
x86/alternatives: Use temporary mm for text poking
x86/alternatives: Initialize temporary mm for patching
fork: Provide a function for copying init_mm
uprobes: Initialize uprobes earlier
x86/mm: Save debug registers when loading a temporary mm
...
This patch provides an arch option, ARCH_SUSPEND_NONZERO_CPU, to
opt-in to allowing suspend to occur on one of the housekeeping CPUs
rather than hardcoded CPU0.
This will allow CPU0 to be a nohz_full CPU with a later change.
It may be possible for platforms with hardware/firmware restrictions
on suspend/wake effectively support this by handing off the final
stage to CPU0 when kernel housekeeping is no longer required. Another
option is to make housekeeping / nohz_full mask dynamic at runtime,
but the complexity could not be justified at this time.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lkml.kernel.org/r/20190411033448.20842-4-npiggin@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds a function to disable secondary CPUs for suspend that are
not necessarily non-zero / non-boot CPUs. Platforms will be able to
use this to suspend using non-zero CPUs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lkml.kernel.org/r/20190411033448.20842-3-npiggin@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make hibernate handle unmapped pages on the direct map when
CONFIG_ARCH_HAS_SET_ALIAS=y is set. These functions allow for setting pages
to invalid configurations, so now hibernate should check if the pages have
valid mappings and handle if they are unmapped when doing a hibernate
save operation.
Previously this checking was already done when CONFIG_DEBUG_PAGEALLOC=y
was configured. It does not appear to have a big hibernating performance
impact. The speed of the saving operation before this change was measured
as 819.02 MB/s, and after was measured at 813.32 MB/s.
Before:
[ 4.670938] PM: Wrote 171996 kbytes in 0.21 seconds (819.02 MB/s)
After:
[ 4.504714] PM: Wrote 178932 kbytes in 0.22 seconds (813.32 MB/s)
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-16-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Measure the filesystems sync time during system sleep more precisely.
Among other things, this allows the pr_cont() to be dropped from
ksys_sync_helper() and makes automatic system suspend and hibernation
profiling somewhat more straightforward.
Signed-off-by: Harry Pan <harry.pan@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Create a common helper to sync filesystems for system suspend and
hibernation.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukasz Luba