[ Upstream commit 14cdc1f243d79e0b46be150502b7dba9c5a6bdfd ]
Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.
Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 970cdc53cb1afa73602028c103dbfb6a230080be ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3bcbcd396175ac26aa54919c0b31c7d2878fc24 ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2948781a72f0d8cf2adf31758c357f2f35e6c79 ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b46d674ac000b101fdad92cf16cc11d90b72f86 ]
Fixed order is the device-tree convention.
The timer driver currently gets clocks by name,
so no changes are needed there.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210506111136.3941-3-ezequiel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfbfb86a43f9a5bbd166d88bca9e07ee4e1bff31 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip ARM tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3036-kylin and rk3288
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc5b59b945b546e27977e99a5ca6fe61179ff0d2 ]
ethernet-phy is not the right name for mdio, fix it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddc873cd3c0af4faad6a00bffda21c3f775126dd ]
The i2c bus can freeze at the end of transaction so the bus can no longer work.
This scenario is improved by adding scl/sda gpios definitions to implement the
i2c bus recovery mechanism.
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2bdd3484890441b9cc2560413a86e8f2aa04157 ]
To make the ethernet cable plugin detection reliable the
power detection of the smsc phy has been disabled.
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c016c26c1631f539c652b5d82242a3ca402545c1 ]
Fix ethernet reset time properties as described in
Documentation/devicetree/bindings/net/ethernet-phy.yaml
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b11fec7345f21995f4ea4bafb0e108b9a620238 ]
ti,pindir-d0-out-d1-in property is expected to be of type boolean.
Therefore, fix the property accordingly.
Fixes: b0b039515445 ("ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 414bfe1d26b60ef20b58e36efd5363188a694bab ]
ti,pindir-d0-out-d1-in property is expected to be of type boolean.
Therefore, fix the property accordingly.
Fixes: 444d66fafa ("ARM: dts: add spi wifi support to cm-t335")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5aede3e6dd1b8ca574600a1ecafe1e580c53f2f ]
1. Reorder interrupts
2. Fix typo: s/spi_lr_overhead/spi_lr_overread/
3. Rename node: s/spi-nor@0/flash@0/
This fixes:
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dt.yaml: spi@18029200: interrupt-names: 'oneOf' conditional failed, one must be fixed:
['spi_lr_fullness_reached', 'spi_lr_session_aborted', 'spi_lr_impatient', 'spi_lr_session_done', 'spi_lr_overhead', 'mspi_done', 'mspi_halted'] is too long
Additional items are not allowed ('spi_lr_session_aborted', 'spi_lr_impatient', 'spi_lr_session_done', 'spi_lr_overhead', 'mspi_done', 'mspi_halted' were unexpected)
'mspi_done' was expected
'spi_l1_intr' was expected
'mspi_halted' was expected
'spi_lr_fullness_reached' was expected
'spi_lr_session_aborted' was expected
'spi_lr_impatient' was expected
'spi_lr_session_done' was expected
'spi_lr_overread' was expected
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dt.yaml: spi-nor@0: $nodename:0: 'spi-nor@0' does not match '^flash(@.*)?$'
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab8c23096a29b69044209a5925758a6f88bd450 ]
"make dtbs_check" complains:
arch/arm/boot/dts/r8a7779-marzen.dt.yaml: display@fff80000: clock-names:0: 'du.0' was expected
Change the first clock name to match the DT bindings.
This has no effect on actual operation, as the Display Unit driver in
Linux does not use the first clock name on R-Car H1, but just grabs the
first clock.
Fixes: 665d79aa47 ("ARM: shmobile: marzen: Add DU external pixel clock to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/9d5e1b371121883b3b3e10a3df43802a29c6a9da.1619699965.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd2f1717966535b7d0b6fe45cf0d79e94330da5f ]
There is no "max_brightness" property as pointed out by dtschema:
arch/arm/boot/dts/exynos5422-odroidxu4.dt.yaml: led-controller: led-1: 'max-brightness' is a required property
Fixes: 6658356014 ("ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-5-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7e59c84cf2055a1894f45855c8319191f2fa59e ]
There is no "max_brightness" property as pointed out by dtschema:
arch/arm/boot/dts/exynos5422-odroidhc1.dt.yaml: led-controller: led-1: 'max-brightness' is a required property
Fixes: 1ac49427b5 ("ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-4-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75121e1dc9fe4def41e63d57f6a53749b88006ed ]
There is no "max_brightness" property. This brings the intentional
brightness reduce of green LED and dtschema checks as well:
arch/arm/boot/dts/exynos5410-odroidxu.dt.yaml: led-controller-1: led-1: 'max-brightness' is a required property
Fixes: 719f39fec5 ("ARM: dts: exynos5422-odroidxu3: Hook up PWM and use it for LEDs")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d551bf20858240f38a0276be3016ff379918ac ]
Early exits from for_each_compatible_node() should decrement the
node reference counter. Reported by Coccinelle:
arch/arm/mach-exynos/exynos.c:52:1-25: WARNING:
Function "for_each_compatible_node" should have of_node_put() before break around line 58.
Fixes: b3205dea8f ("ARM: EXYNOS: Map SYSRAM through generic DT bindings")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210425174945.164612-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3bb3d27cd371d3edb43eeb1beb8ae4e92a356d ]
Two ethernet node was added by
commit 95220046a6 ("ARM: dts: Add ethernet to a bunch of platforms")
and commit d6d0cef55e ("ARM: dts: Add the FOTG210 USB host to Gemini boards")
This patch removes the duplicate one.
Fixes: d6d0cef55e ("ARM: dts: Add the FOTG210 USB host to Gemini boards")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b95a7d90ce8160ac5cffd5bace6e2eba01a871e ]
There's a few instructions that GAS infers operands but Clang doesn't;
from what I can tell the Arm ARM doesn't say these are optional.
F5.1.257 TBB, TBH T1 Halfword variant
F5.1.238 STREXD T1 variant
F5.1.84 LDREXD T1 variant
Link: https://github.com/ClangBuiltLinux/linux/issues/1309
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Jian Cai <jiancai@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dad7b9896a5dbac5da8275d5a6147c65c81fb5f2 upstream.
When building the kernel wtih gcc-10 or higher using the
CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE=y flag, the compiler picks a slightly
different set of registers for the inline assembly in cpu_init() that
subsequently results in a corrupt kernel stack as well as remaining in
FIQ mode. If a banked register is used for the last argument, the wrong
version of that register gets loaded into CPSR_c. When building in Arm
mode, the arguments are passed as immediate values and the bug cannot
happen.
This got introduced when Daniel reworked the FIQ handling and was
technically always broken, but happened to work with both clang and gcc
before gcc-10 as long as they picked one of the lower registers.
This is probably an indication that still very few people build the
kernel in Thumb2 mode.
Marek pointed out the problem on IRC, Arnd narrowed it down to this
inline assembly and Russell pinpointed the exact bug.
Change the constraints to force the final mode switch to use a non-banked
register for the argument to ensure that the correct constant gets loaded.
Another alternative would be to always use registers for the constant
arguments to avoid the #ifdef that has now become more complex.
Cc: <stable@vger.kernel.org> # v3.18+
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Fixes: c0e7f7ee71 ("ARM: 8150/3: fiq: Replace default FIQ handler")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25de4ce5ed02994aea8bc111d133308f6fd62566 upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
[tony@atomide.com: backported to 5.4.y]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3efe7a878a11c13b5297057bfc1e5639ce1241ce upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm timers instead.
Let's prepare for adding support for percpu timers by adding a common
dmtimer_clkevt_init_common() and call it from __omap_sync32k_timer_init().
This patch makes no intentional functional changes.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
[tony@atomide.com: backported to 5.4.y]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52762fbd1c4778ac9b173624ca0faacd22ef4724 upstream.
We can move the TI dmtimer clockevent and clocksource to live under
drivers/clocksource if we rely only on the clock framework, and handle
the module configuration directly in the clocksource driver based on the
device tree data.
This removes the early dependency with system timers to the interconnect
related code, and we can probe pretty much everything else later on at
the module_init level.
Let's first add a new driver for timer-ti-dm-systimer based on existing
arch/arm/mach-omap2/timer.c. Then let's start moving SoCs to probe with
device tree data while still keeping the old timer.c. And eventually we
can just drop the old timer.c.
Let's take the opportunity to switch to use readl/writel as pointed out
by Daniel Lezcano <daniel.lezcano@linaro.org>. This allows further
clean-up of the timer-ti-dm code the a lot of the shared helpers can
just become static to the non-syster related code.
Note the boards can optionally configure different timer source clocks
if needed with assigned-clocks and assigned-clock-parents.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
[tony@atomide.com: backported to 5.4.y]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b75ca5217743e4d7076cf65e044e88389e44318d upstream.
request_irq() is preferred over setup_irq(). Invocations of setup_irq()
occur after memory allocators are ready.
Per tglx[1], setup_irq() existed in olden days when allocators were not
ready by the time early interrupts were initialized.
Hence replace setup_irq() by request_irq().
[1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 040ab72ee10ea88e1883ad143b3e2b77596abc31 ]
GCC reports the following warning with W=1:
arch/arm/mach-omap2/board-n8x0.c:325:19: warning:
variable 'index' set but not used [-Wunused-but-set-variable]
325 | int bit, *openp, index;
| ^~~~~
Fix this by moving CONFIG_MMC_OMAP to cover the rest codes
in the n8x0_mmc_callback().
Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8967b27a6c1c19251989c7ab33c058d16e4a5f53 upstream.
Per schematic, both PU and SOC regulator are supplied from LTC3676 SW1
via VDDSOC_IN rail, add the PU input. Both VDD1P1, VDD2P5 are supplied
from LTC3676 SW2 via VDDHIGH_IN rail, add both inputs.
While no instability or problems are currently observed, the regulators
should be fully described in DT and that description should fully match
the hardware, else this might lead to unforseen issues later. Fix this.
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e4a4a08cd78efcaddbc2e4c5ed86b5a5cb8a15e upstream.
The FEC does not have a PHY so it should not have a phy-handle. It is
connected to the switch at RGMII level so we need a fixed-link sub-node
on both ends.
This was not a problem until the qca8k.c driver was converted to PHYLINK
by commit b3591c2a3661 ("net: dsa: qca8k: Switch to PHYLINK instead of
PHYLIB"). That commit revealed the FEC configuration was not correct.
Fixes: 87489ec3a7 ("ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e2fa4959c4f44815ce33e46e4054eeb0f346053 ]
According to Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml, the
correct name of the property is 'fsl,tuning-step'.
Fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fixes: f13f571ac8 ("ARM: dts: imx7d-pico: Extend peripherals support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c8f0338cdacc90fdf6468adafa8e27952987f00 ]
According to Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml, the
correct name of the property is 'fsl,tuning-step'.
Fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fixes: ae7b3384b6 ("ARM: dts: Add support for 96Boards Meerkat96 board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 263d6287da1433aba11c5b4046388f2cdf49675c upstream.
When a VCPU is created, the kvm_vcpu struct is initialized to zero in
kvm_vm_ioctl_create_vcpu(). On VHE systems, the first time
vcpu.arch.mdcr_el2 is loaded on hardware is in vcpu_load(), before it is
set to a sensible value in kvm_arm_setup_debug() later in the run loop. The
result is that KVM executes for a short time with MDCR_EL2 set to zero.
This has several unintended consequences:
* Setting MDCR_EL2.HPMN to 0 is constrained unpredictable according to ARM
DDI 0487G.a, page D13-3820. The behavior specified by the architecture
in this case is for the PE to behave as if MDCR_EL2.HPMN is set to a
value less than or equal to PMCR_EL0.N, which means that an unknown
number of counters are now disabled by MDCR_EL2.HPME, which is zero.
* The host configuration for the other debug features controlled by
MDCR_EL2 is temporarily lost. This has been harmless so far, as Linux
doesn't use the other fields, but that might change in the future.
Let's avoid both issues by initializing the VCPU's mdcr_el2 field in
kvm_vcpu_vcpu_first_run_init(), thus making sure that the MDCR_EL2 register
has a consistent value after each vcpu_load().
Fixes: d5a21bcc29 ("KVM: arm64: Move common VHE/non-VHE trap config in separate functions")
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210407144857.199746-3-alexandru.elisei@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57ac51667d8cd62731223d687e5fe7b41c502f89 ]
On Qualcomm ARM32 platforms, the SMC call can return before it has
completed. If this occurs, the call can be restarted, but it requires
using the returned session ID value from the interrupted SMC call.
The ARM32 SMCC code already has the provision to add platform specific
quirks for things like this. So let's make use of it and add the
Qualcomm specific quirk (ARM_SMCCC_QUIRK_QCOM_A6) used by the QCOM_SCM
driver.
This change is similar to the below one added for ARM64 a while ago:
commit 82bcd08702 ("firmware: qcom: scm: Fix interrupted SCM calls")
Without this change, the Qualcomm ARM32 platforms like SDX55 will return
-EINVAL for SMC calls used for modem firmware loading and validation.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8252ca87c7a2111502ee13994956f8c309faad7f ]
Enabling function_graph tracer on ARM causes kernel panic, because the
function graph tracer updates the "return address" of a function in order
to insert a trace callback on function exit, it saves the function's
original return address in a return trace stack, but cpu_suspend() may not
return through the normal return path.
cpu_suspend() will resume directly via the cpu_resume path, but the return
trace stack has been set-up by the subfunctions of cpu_suspend(), which
makes the "return address" inconsistent with cpu_suspend().
This patch refers to Commit de818bd452
("arm64: kernel: pause/unpause function graph tracer in cpu_suspend()"),
fixes the issue by pausing/resuming the function graph tracer on the thread
executing cpu_suspend(), so that the function graph tracer state is kept
consistent across functions that enter power down states and never return
by effectively disabling graph tracer while they are executing.
Signed-off-by: louis.wang <liang26812@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 10fce53c0ef8f6e79115c3d9e0d7ea1338c3fa37 upstream
The early ATAGS/DT mapping code uses SECTION_SHIFT to mask low order
bits of R2, and decides that no ATAGS/DTB were provided if the resulting
value is 0x0.
This means that on systems where DRAM starts at 0x0 (such as Raspberry
Pi), no explicit mapping of the DT will be created if R2 points into the
first 1 MB section of memory. This was not a problem before, because the
decompressed kernel is loaded at the base of DRAM and mapped using
sections as well, and so as long as the DT is referenced via a virtual
address that uses the same translation (the linear map, in this case),
things work fine.
However, commit 7a1be318f579 ("9012/1: move device tree mapping out of
linear region") changes this, and now the DT is referenced via a virtual
address that is disjoint from the linear mapping of DRAM, and so we need
the early code to create the DT mapping unconditionally.
So let's create the early DT mapping for any value of R2 != 0x0.
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc2933c133744305236793025b00c2f7d258b687 upstream
Commit
149a3ffe62b9dbc3 ("9012/1: move device tree mapping out of linear region")
created a permanent, read-only section mapping of the device tree blob
provided by the firmware, and added a set of macros to get the base and
size of the virtually mapped FDT based on the physical address. However,
while the mapping code uses the SECTION_SIZE macro correctly, the macros
use PMD_SIZE instead, which means something entirely different on ARM when
using short descriptors, and is therefore not the right quantity to use
here. So replace PMD_SIZE with SECTION_SIZE. While at it, change the names
of the macro and its parameter to clarify that it returns the virtual
address of the start of the FDT, based on the physical address in memory.
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a1be318f5795cb66fa0dc86b3ace427fe68057f upstream
On ARM, setting up the linear region is tricky, given the constraints
around placement and alignment of the memblocks, and how the kernel
itself as well as the DT are placed in physical memory.
Let's simplify matters a bit, by moving the device tree mapping to the
top of the address space, right between the end of the vmalloc region
and the start of the the fixmap region, and create a read-only mapping
for it that is independent of the size of the linear region, and how it
is organized.
Since this region was formerly used as a guard region, which will now be
populated fully on LPAE builds by this read-only mapping (which will
still be able to function as a guard region for stray writes), bump the
start of the [underutilized] fixmap region by 512 KB as well, to ensure
that there is always a proper guard region here. Doing so still leaves
ample room for the fixmap space, even with NR_CPUS set to its maximum
value of 32.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9a2f8b599d0bc22a1b13e69527246ac39c697b4 upstream
Before moving the DT mapping out of the linear region, let's prepare
for this change by removing all the phys-to-virt translations of the
__atags_pointer variable, and perform this translation only once at
setup time.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a506bd5756290821a4314f502b4bafc2afcf5260 ]
The commit 1879445dfa ("perf/core: Set event's default
::overflow_handler()") set a default event->overflow_handler in
perf_event_alloc(), and replace the check event->overflow_handler with
is_default_overflow_handler(), but one is missing.
Currently, the bp->overflow_handler can not be NULL. As a result,
enable_single_step() is always not invoked.
Comments from Zhen Lei:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/20210207105934.2001-1-thunder.leizhen@huawei.com/
Fixes: 1879445dfa ("perf/core: Set event's default ::overflow_handler()")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Cc: Wang Nan <wangnan0@huawei.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ba585cc5b56ea14a453ba6be9bdb984ed33471a ]
UniPhier PXs2 boards have RTL8211E ethernet phy, and the phy have the RX/TX
delays of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
After the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: e3cc931921 ("ARM: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8987efbb17c2522be8615085df9a14da2ab53d34 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: c61248afa8 ("ARM: dts: Add max77686 RTC interrupt to cros5250-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-9-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6368c60561370e4a92fac22982a3bd656172170 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 47580e8d94 ("ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6503c568e97a52f8b7a3109718db438e52e59485 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: eea6653aae ("ARM: dts: Enable PMIC interrupts for exynos4412-odroid-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e52dcd6e70fab51f53292e53336ecb007bb60889 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 15dfdfad2d ("ARM: dts: Add basic dts for Exynos4412-based Trats 2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-5-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15107e443ab8c6cb35eff10438993e4bc944d9ae ]
The Maxim MUIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 7eec126675 ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a45f33bd36efbb624198cfa9fdf1f66fd1c3d26 ]
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: e8614292cd ("ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4e792d1acce31c2eb7b9193ab06ab94de05bf42 upstream.
The LLVM ld.lld linker uses a different symbol type for __bss_start,
resulting in the calculation of KBSS_SZ to be thrown off. Up until now,
this has gone unnoticed as it only affects the appended DTB case, but
pending changes for ARM in the way the decompressed kernel is cleaned
from the caches has uncovered this problem.
On a ld.lld build:
$ nm vmlinux |grep bss_
c1c22034 D __bss_start
c1c86e98 B __bss_stop
resulting in
$ readelf -s arch/arm/boot/compressed/vmlinux | grep bss_size
433: c1c86e98 0 NOTYPE GLOBAL DEFAULT ABS _kernel_bss_size
which is obviously incorrect, and may cause the cache clean to access
unmapped memory, or cause the size calculation to wrap, resulting in no
cache clean to be performed at all.
Fix this by updating the sed regex to take D type symbols into account.
Link: https://lore.kernel.org/linux-arm-kernel/6c65bcef-d4e7-25fa-43cf-2c435bb61bb9@collabora.com/
Link: https://lore.kernel.org/linux-arm-kernel/20210205085220.31232-1-ardb@kernel.org/
Cc: <stable@vger.kernel.org> # v4.19+
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1ebdb3741993f853865d1bd8f77881916ad53a7 ]
Also some omap3 devices like n900 seem to have eMMC and micro-sd swapped
around with commit 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for
drivers that existed in v4.4").
Let's fix the issue with aliases as discussed on the mailing lists. While
the mmc aliases should be board specific, let's first fix the issue with
minimal changes.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d2f7eca60b29006285d57c7035539e33300e89e5 upstream.
Since uprobes is not supported for thumb, check that the thumb bit is
not set when matching the uprobes instruction hooks.
The Arm UDF instructions used for uprobes triggering
(UPROBE_SWBP_ARM_INSN and UPROBE_SS_ARM_INSN) coincidentally share the
same encoding as a pair of unallocated 32-bit thumb instructions (not
UDF) when the condition code is 0b1111 (0xf). This in effect makes it
possible to trigger the uprobes functionality from thumb, and at that
using two unallocated instructions which are not permanently undefined.
Signed-off-by: Fredrik Strupe <fredrik@strupe.net>
Cc: stable@vger.kernel.org
Fixes: c7edc9e326 ("ARM: add uprobes support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30e3b4f256b4e366a61658c294f6a21b8626dda7 ]
Since commit 30fdfb929e ("PCI: Add a call to pci_assign_irq() in
pci_device_probe()"), the PCI code will call the IRQ mapping function
whenever a PCI driver is probed. If these are marked as __init, this
causes an oops if a PCI driver is loaded or bound after the kernel has
initialised.
Fixes: 30fdfb929e ("PCI: Add a call to pci_assign_irq() in pci_device_probe()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28399a5a6d569c9bdb612345e4933046ca37cde5 ]
The clang integrated assembler fails to build one file with
a complex asm instruction:
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: error: invalid instruction, any one of the following would fix this:
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: note: instruction requires: armv6t2
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: note: instruction requires: thumb2
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
The problem is that 'NR_IRQS_LEGACY' is not defined here. Apparently
gas does not care because we first add and then subtract this number,
leading to the immediate value to be the same regardless of the
specific definition of NR_IRQS_LEGACY.
Neither the way that 'gas' just silently builds this file, nor the
way that clang IAS makes nonsensical suggestions for how to fix it
is great. Fortunately there is an easy fix, which is to #include
the header that contains the definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210308153430.2530616-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 844b85dda2f569943e1e018fdd63b6f7d1d6f08e ]
clang warns about an impossible condition when building with 32-bit
phys_addr_t:
arch/arm/mach-keystone/keystone.c:79:16: error: result of comparison of constant 51539607551 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
mem_end > KEYSTONE_HIGH_PHYS_END) {
~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-keystone/keystone.c:78:16: error: result of comparison of constant 34359738368 with expression of type 'phys_addr_t' (aka 'unsigned int') is always true [-Werror,-Wtautological-constant-out-of-range-compare]
if (mem_start < KEYSTONE_HIGH_PHYS_START ||
~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~
Change the temporary variable to a fixed-size u64 to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Link: https://lore.kernel.org/r/20210323131814.2751750-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77335a040178a0456d4eabc8bf17a7ca3ee4a327 ]
Fix moving mmc devices with dts aliases as discussed on the lists.
Without this we now have internal eMMC mmc1 show up as mmc2 compared
to the earlier order of devices.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 140a776833957539c84301dbdb4c3013876de118 ]
We have a duplicate legacy clock defined for sha2md5_fck that can
sometimes race with clk_disable() with the dts configured clock
for OMAP4_SHA2MD5_CLKCTRL when unused clocks are disabled during
boot causing an "Unhandled fault: imprecise external abort".
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f57011e72f5fe0421ec7a812beb1b57bdf4bb47f ]
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module")
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a26c56ae67fa9fbb45a8a232dcd7ebaa7af16086 upstream.
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bbce32a20d6a72c767a7f85fd6127babd1410ac ]
Without DT aliases, the numbering of mmc interfaces is unpredictable.
Adding them makes it possible to refer to devices consistently. The
popular suggestion to use UUIDs obviously doesn't work with a blank
device fresh from the factory.
See commit fa2d0aa96941 ("mmc: core: Allow setting slot index via
device tree alias") for more discussion.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 221c3a09ddf70a0a51715e6c2878d8305e95c558 upstream.
Fix the phy address to 7 for Ethernet PHY on SAMA5D27 SOM1. No
connection established if phy address 0 is used.
The board uses the 24 pins version of the KSZ8081RNA part, KSZ8081RNA
pin 16 REFCLK as PHYAD bit [2] has weak internal pull-down. But at
reset, connected to PD09 of the MPU it's connected with an internal
pull-up forming PHYAD[2:0] = 7.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: 2f61929eb1 ("ARM: dts: at91: at91-sama5d27_som1: fix PHY ID")
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cce9d44321e460e7c88cdec4e4537a6e9ad7c0d upstream.
Commit f77ac2e378be9dd6 ("ARM: 9030/1: entry: omit FP emulation for UND
exceptions taken in kernel mode") failed to take into account that there
is in fact a case where we relied on this code path: during boot, the
VFP detection code issues a read of FPSID, which will trigger an undef
exception on cores that lack VFP support.
So let's reinstate this logic using an undef hook which is registered
only for the duration of the initcall to vpf_init(), and which sets
VFP_arch to a non-zero value - as before - if no VFP support is present.
Fixes: f77ac2e378be9dd6 ("ARM: 9030/1: entry: omit FP emulation for UND ...")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f77ac2e378be9dd61eb88728f0840642f045d9d1 upstream.
There are a couple of problems with the exception entry code that deals
with FP exceptions (which are reported as UND exceptions) when building
the kernel in Thumb2 mode:
- the conditional branch to vfp_kmode_exception in vfp_support_entry()
may be out of range for its target, depending on how the linker decides
to arrange the sections;
- when the UND exception is taken in kernel mode, the emulation handling
logic is entered via the 'call_fpe' label, which means we end up using
the wrong value/mask pairs to match and detect the NEON opcodes.
Since UND exceptions in kernel mode are unlikely to occur on a hot path
(as opposed to the user mode version which is invoked for VFP support
code and lazy restore), we can use the existing undef hook machinery for
any kernel mode instruction emulation that is needed, including calling
the existing vfp_kmode_exception() routine for unexpected cases. So drop
the call to call_fpe, and instead, install an undef hook that will get
called for NEON and VFP instructions that trigger an UND exception in
kernel mode.
While at it, make sure that the PC correction is accurate for the
execution mode where the exception was taken, by checking the PSR
Thumb bit.
[nd: fix conflict in arch/arm/vfp/vfphw.S due to missing
commit 2cbd1cc3dcd3 ("ARM: 8991/1: use VFP assembler mnemonics if
available")]
Fixes: eff8728fe698 ("vmlinux.lds.h: Add PGO and AutoFDO input sections")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 01dc9262ff5797b675c32c0c6bc682777d23de05 upstream.
It recently became apparent that the ARMv8 architecture has interesting
rules regarding attributes being used when fetching instructions
if the MMU is off at Stage-1.
In this situation, the CPU is allowed to fetch from the PoC and
allocate into the I-cache (unless the memory is mapped with
the XN attribute at Stage-2).
If we transpose this to vcpus sharing a single physical CPU,
it is possible for a vcpu running with its MMU off to influence
another vcpu running with its MMU on, as the latter is expected to
fetch from the PoU (and self-patching code doesn't flush below that
level).
In order to solve this, reuse the vcpu-private TLB invalidation
code to apply the same policy to the I-cache, nuking it every time
the vcpu runs on a physical CPU that ran another vcpu of the same
VM in the past.
This involve renaming __kvm_tlb_flush_local_vmid() to
__kvm_flush_cpu_context(), and inserting a local i-cache invalidation
there.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210303164505.68492-1-maz@kernel.org
[maz: added 32bit ARM support]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8310b77b48c5558c140e7a57a702e7819e62f04e upstream.
Bailing immediately from set_foreign_p2m_mapping() upon a p2m updating
error leaves the full batch in an ambiguous state as far as the caller
is concerned. Instead flags respective slots as bad, unmapping what
was mapped there right away.
HYPERVISOR_grant_table_op()'s return value and the individual unmap
slots' status fields get used only for a one-time - there's not much we
can do in case of a failure.
Note that there's no GNTST_enomem or alike, so GNTST_general_error gets
used.
The map ops' handle fields get overwritten just to be on the safe side.
This is part of XSA-367.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/96cccf5d-e756-5f53-b91a-ea269bfb9be0@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d050d049f8b8077025292c1ecf456c4ee7f96861 upstream.
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201202051634.490-2-wangzhiqiang.bj@bytedance.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2acb909750431030b65a0a2a17fd8afcbd813a84 ]
It was observed that decompressor running on hardware implementing ARM v8.2
Load/Store Multiple Atomicity and Ordering Control (LSMAOC), say, as guest,
would stuck just after:
Uncompressing Linux... done, booting the kernel.
The reason is that it clears nTLSMD bit when disabling caches:
nTLSMD, bit [3]
When ARMv8.2-LSMAOC is implemented:
No Trap Load Multiple and Store Multiple to
Device-nGRE/Device-nGnRE/Device-nGnRnE memory.
0b0 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are trapped and
generate a stage 1 Alignment fault.
0b1 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are not trapped.
This bit is permitted to be cached in a TLB.
This field resets to 1.
Otherwise:
Reserved, RES1
So as effect we start getting traps we are not quite ready for.
Looking into history it seems that mask used for SCTLR clear came from
the similar code for ARMv4, where bit[3] is the enable/disable bit for
the write buffer. That not applicable to ARMv7 and onwards, so retire
that bit from the masks.
Fixes: 7d09e85448 ("[ARM] 4393/2: ARMv7: Add uncompressing code for the new CPU Id format")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a3b8758bd6e45f7b671723b5c9fa2b69d0787ae ]
Compile-testing the ixp4xx timer with CONFIG_OF enabled but
CONFIG_TIMER_OF disabled leads to a harmless warning:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ixp4xx.o' being placed in section `__timer_of_table'
Move the select statement from the platform code into the driver
so it always gets enabled in configurations that rely on it.
Fixes: 40df14cc5c ("clocksource/drivers/ixp4xx: Add OF initialization support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210103135955.3808976-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46ecdfc1830eaa40a11d7f832089c82b0e67ea96 ]
Split up the pins for each fan. This is needed in order to control them
Fixes: ced8025b56 ("ARM: dts: armada388-helios4")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44f416879a442600b006ef7dec3a6dc98bcf59c6 ]
We have gpio_86 wired internally to the bandgap thermal shutdown
interrupt on 4430 like we have it on 4460 according to the TRM.
This can be found easily by searching for TSHUT.
For some reason the thermal shutdown interrupt was never added
for 4430, let's add it. I believe this is needed for the thermal
shutdown interrupt handler ti_bandgap_tshut_irq_handler() to call
orderly_poweroff().
Fixes: aa9bb4bb88 ("arm: dts: add omap4430 thermal data")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e7d9a583a24f7582c6bc29a0d4d624feedbc2f9 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: aac4e06153 ("ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ac8893c4fa3d4a34915dc5cdab568a39db5086c ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: 1fed225271 ("ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-5-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e6a5467cb8657cf8b5e610a30a4c502085e4f9 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 437ae60947716bb479e2f32466f49445c0509b1e ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: faaf348ef4 ("ARM: dts: Add board dts file for exynos3250-rinato")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8528cda2b7c667e9cd173aef1a677c71b7d5a096 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: e0cefb3f79 ("ARM: dts: add board dts file for Exynos3250-based Monk board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-2-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb31334687db31c691901269d65074a7ffaecb18 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: b004a34bd0 ("ARM: dts: exynos: Add exynos3250-artik5 dtsi file for ARTIK5 module")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-1-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 36bf1dfb8b266e089afa9b7b984217f17027bf35 upstream.
set_phys_to_machine can fail due to lack of memory, see the kzalloc call
in arch/arm/xen/p2m.c:__set_phys_to_machine_multi.
Don't ignore the potential return error in set_foreign_p2m_mapping,
returning it to the caller instead.
This is part of XSA-361.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Cc: stable@vger.kernel.org
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d62e81b60d4025e2dfcd5ea531cc1394ce9226f ]
Giancarlo Ferrari reports the following oops while trying to use kexec:
Unable to handle kernel paging request at virtual address 80112f38
pgd = fd7ef03e
[80112f38] *pgd=0001141e(bad)
Internal error: Oops: 80d [#1] PREEMPT SMP ARM
...
This is caused by machine_kexec() trying to set the kernel text to be
read/write, so it can poke values into the relocation code before
copying it - and an interrupt occuring which changes the page tables.
The subsequent writes then hit read-only sections that trigger a
data abort resulting in the above oops.
Fix this by copying the relocation code, and then writing the variables
into the destination, thereby avoiding the need to make the kernel text
read/write.
Reported-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com>
Tested-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c698bff66ab4914bb3d71da7dc6112519bde23e ]
Ensure that the signal page contains our poison instruction to increase
the protection against ROP attacks and also contains well defined
contents.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5638159f6d93b99ec9743ac7f65563fca3cf413d ]
This reverts commit c17e9377aa.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06862d789ddde8a99c1e579e934ca17c15a84755 ]
We get suspcious RCU usage splats with cpuidle in several places in
omap_enter_idle_coupled() with the kernel debug options enabled:
RCU used illegally from extended quiescent state!
...
(_raw_spin_lock_irqsave)
(omap_enter_idle_coupled+0x17c/0x2d8)
(omap_enter_idle_coupled)
(cpuidle_enter_state)
(cpuidle_enter_state_coupled)
(cpuidle_enter)
Let's use RCU_NONIDLE to suppress these splats. Things got changed around
with commit 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the
idle path") that started triggering these warnings.
For the tick_broadcast related calls, ideally we'd just switch over to
using CPUIDLE_FLAG_TIMER_STOP for omap_enter_idle_coupled() to have the
generic cpuidle code handle the tick_broadcast related calls for us and
then just drop the tick_broadcast calls here.
But we're currently missing the call in the common cpuidle code for
tick_broadcast_enable() that CPU1 hotplug needs as described in earlier
commit 50d6b3cf94 ("ARM: OMAP2+: fix lack of timer interrupts on CPU1
after hotplug").
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4295ab0b485b8bc50d2264bcae2acd06f25caaf upstream.
After Commit 3499ba8198cad ("xen: Fix event channel callback via
INTX/GSI"), xenbus_probe() will be called too early on Arm. This will
recent to a guest hang during boot.
If the hang wasn't there, we would have ended up to call
xenbus_probe() twice (the second time is in xenbus_probe_initcall()).
We don't need to initialize xenbus_probe() early for Arm guest.
Therefore, the call in xen_guest_init() is now removed.
After this change, there is no more external caller for xenbus_probe().
So the function is turned to a static one. Interestingly there were two
prototypes for it.
Cc: stable@vger.kernel.org
Fixes: 3499ba8198cad ("xen: Fix event channel callback via INTX/GSI")
Reported-by: Ian Jackson <iwj@xenproject.org>
Signed-off-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20210210170654.5377-1-julien@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39d3454c3513840eb123b3913fda6903e45ce671 upstream.
Building with gcc 4.9.2 reveals a latent bug in the PCI accessors
for Footbridge platforms, which causes a fatal alignment fault
while accessing IO memory. Fix this by making the assembly volatile.
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a900cac3750b9f0b8f5ed0503d9c6359532f644d ]
BPi Pro needs TX and RX delay for Gbit to work reliable and avoid high
packet loss rates. The realtek phy driver overrides the settings of the
pull ups for the delays, so fix this for BananaPro.
Fix the phy-mode description to correctly reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 10662a33dc ("ARM: dts: sun7i: Add dts file for Bananapro board")
Signed-off-by: Hermann Lauer <Hermann.Lauer@uni-heidelberg.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210128111842.GA11919@lemon.iwr.uni-heidelberg.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a88afa46b86ff461c89cc33fc3a45267fff053e8 upstream.
When the kernel is configured to use the Thumb-2 instruction set
"suspend-to-memory" fails to resume. Observed on a Colibri iMX6ULL
(i.MX 6ULL) and Apalis iMX6 (i.MX 6Q).
It looks like the CPU resumes unconditionally in ARM instruction mode
and then chokes on the presented Thumb-2 code it should execute.
Fix this by using the arm instruction set for all code in
suspend-imx6.S.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Fixes: df595746fa ("ARM: imx: add suspend in ocram support for i.mx6q")
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3499ba8198cad47b731792e5e56b9ec2a78a83a2 ]
For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().
We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.
To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.
Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bac717171971176b78c72d15a8b6961764ab197f ]
dtc points out that the interrupts for some devices are not parsable:
picoxcell-pc3x2.dtsi:45.19-49.5: Warning (interrupts_property): /paxi/gem@30000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:51.21-55.5: Warning (interrupts_property): /paxi/dmac@40000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:57.21-61.5: Warning (interrupts_property): /paxi/dmac@50000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:233.21-237.5: Warning (interrupts_property): /rwid-axi/axi2pico@c0000000: Missing interrupt-parent
There are two VIC instances, so it's not clear which one needs to be
used. I found the BSP sources that reference VIC0, so use that:
https://github.com/r1mikey/meta-picoxcell/blob/master/recipes-kernel/linux/linux-picochip-3.0/0001-picoxcell-support-for-Picochip-picoXcell-SoC.patch
Acked-by: Jamie Iles <jamie@jamieiles.com>
Link: https://lore.kernel.org/r/20201230152010.3914962-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ec76c2eea903947202098090bbe07a739b5246e9 upstream.
On the GTA04A5 od->_driver_status was not set to BUS_NOTIFY_BIND_DRIVER
during probe of the second mmc used for wifi. Therefore
omap_device_late_idle idled the device during probing causing oopses when
accessing the registers.
It was not set because od->_state was set to OMAP_DEVICE_STATE_IDLE
in the notifier callback. Therefore set od->_driver_status also in that
case.
This came apparent after commit 21b2cec61c04 ("mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4") causing this
oops:
omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling
8<--- cut here ---
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0b402c
...
(omap_hsmmc_set_bus_width) from [<c07996bc>] (omap_hsmmc_set_ios+0x11c/0x258)
(omap_hsmmc_set_ios) from [<c077b2b0>] (mmc_power_up.part.8+0x3c/0xd0)
(mmc_power_up.part.8) from [<c077c14c>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c077d284>] (mmc_add_host+0x58/0x84)
(mmc_add_host) from [<c0799190>] (omap_hsmmc_probe+0x5fc/0x8c0)
(omap_hsmmc_probe) from [<c0666728>] (platform_drv_probe+0x48/0x98)
(platform_drv_probe) from [<c066457c>] (really_probe+0x1dc/0x3b4)
Fixes: 04abaf07f6 ("ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer")
Fixes: 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
[tony@atomide.com: left out extra parens, trimmed description stack trace]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes a build failure because of undefined symbols in i.MX6UL-only
configurations. The same is done in rel_imx_4.14.78_1.0.0_ga.
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
(cherry picked from commit 129a6fad43b89565af5a6463e29d1cf42b62bc0b)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
smp_wfe_imx6 is only used for i.MX6Q. Including it in i.MX6SX-only
configurations causes two build issues:
- The symbols it defines conflict with fallback definitions in common.c
- It scu_power_mode, which is undefined without HAVE_ARM_SCU
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
(cherry picked from commit e85ce3157725a6e3e77a17d6c4e0acec9de1d690)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
All i.MX6 variants reference imx_busfreq_map_io() and thus fail to build
without Busfreq.
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
(cherry picked from commit 4f49200132e6d252cca49d5d97be69a7a26495a2)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
busfreq-imx.c fails to build when HAVE_IMX_BUSFREQ is not set.
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
(cherry picked from commit 5d229c51b5a5265abdb16f4e8a082816020da7a7)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The ECSPI1 is not used for a FRAM chip, so remove the comment.
While at it, also change some whitespaces to tabs to comply with the
indentation style of the rest of the file.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit cc55c85d257e5d8435592643f4aeee683a8fa46f)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
To silence the warnings shown by the driver at boot time, we add a
fixed regulator for the 5V supply of usbotg2 and specify the polarity
of the overcurrent signal for usbotg1.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 43584861ce20fd95d31d665b84ac89dc76c4c8bd)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The Kontron N6x1x SoMs all use uart4 as a debug serial interface.
Therefore we set it in the 'chosen' node.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 36f42bb4d7f90cea20bfb56dd7ab2aa8d0929ca7)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The 'N6311 S' and the 'N6411 S' are similar to the Kontron 'N6310 S'
evaluation kit boards. Instead of the N6310 SoM, they feature a N6311
or N6411 SoM.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 2e426b2bdc69721723016f1067a77bb66ab90a27)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The baseboard for the Kontron N6310 SoM is also used for other SoMs
such as N6311 and N6411. In order to share the code, we move the
definitions of the baseboard to a separate dtsi file.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 3b5212cc2af7160a591bd5d32acbf39ec719023f)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The N6311 and the N6411 SoM are similar to the Kontron N6310 SoM.
They are pin-compatible, but feature a larger RAM and NAND flash
(512MiB instead of 256MiB). Further, the N6411 has an i.MX6ULL SoC,
instead of an i.MX6UL.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 6dd2ed73f4f6a17cb3c753dd75579942fc644a90)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The Kontron N6311 and N6411 SoMs are very similar to N6310. In
preparation to add support for them, we move the common nodes to a
separate file imx6ul-kontron-n6x1x-som-common.dtsi.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit b419b89b20ccb7b2c7adcbcb9ce42a27ea542c43)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The imx_soc_device_init functions tries to fetch the ocotp regmap in
order to soc serial number. If regmap fetch fails then a message is
printed but regmap_read is called anyway and the system crashes.
Failing to lookup ocotp regmap shouldn't be a fatal boot error so check
that the pointer is valid.
Only side-effect of ocotp lookup failure now is that serial number will
be reported as all-zeros which is acceptable.
Cc: stable@vger.kernel.org
Fixes: 8267ff89b713 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 7947e3238b64c00c396e6f5738f94c4d653bc6a2)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
After the commit 8267ff89b713 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
the kernel doesn't start on i.MX6ULL/ULZ SoC.
Tested on next-20191205.
For i.MX6ULL/ULZ the variable "ocotp_compat" is set to "fsl,imx6ul-ocotp", but with commit
ffbc34bf0e ("nvmem: imx-ocotp: Implement i.MX6ULL/ULZ support") and commit
f243bc821e ("ARM: dts: imx6ull: Fix i.MX6ULL/ULZ ocotp compatible") the value
"fsl,imx6ull-ocotp" is already defined and set in device tree...
By setting "ocotp_compat" to "fsl,imx6ull-ocotp" the kernel does boot.
Fixes: 8267ff89b713 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 125ad46f3861520fdebd15c38e4bc412a7add01c)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
i.MX6/7 SoCs have a 64-bit SoC unique ID stored in OCOTP,
it can be used as SoC serial number, add this support for
i.MX6Q/6DL/6SL/6SX/6SLL/6UL/6ULL/6ULZ/7D, see below example
on i.MX6Q:
root@imx6qpdlsolox:~# cat /sys/devices/soc0/serial_number
240F31D4E1FDFCA7
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 8267ff89b71317407f2c6938bd66f3a87070e45f)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
-----BEGIN PGP SIGNATURE-----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=fZ3T
-----END PGP SIGNATURE-----
Merge tag 'v5.4.73' into 5.4-2.3.x-imx
This is the 5.4.73 stable release
Conflicts:
- arch/arm/boot/dts/imx6sl.dtsi:
Commit [a1767c9019] in NXP tree is now covered with commit [5c4c2f437c]
from upstream.
- drivers/gpu/drm/mxsfb/mxsfb_drv.c:
Resolve merge hunk for patch [ed8b90d303] from upstream
- drivers/media/i2c/ov5640.c:
Patch [aa4bb8b883] in NXP tree is now covered by patches [79ec0578c7]
and [b2f8546056] from upstream. Changes from NXP patch [99aa4c8c18] are
covered in upstream version as well.
- drivers/net/ethernet/freescale/fec_main.c:
Fix merge fuzz for patch [9e70485b40] from upstream.
- drivers/usb/cdns3/gadget.c:
Keep NXP version of the file, upstream version is not compatible.
- drivers/usb/dwc3/core.c:
- drivers/usb/dwc3/core.h:
Fix merge fuzz of patch [08045050c6] together wth NXP patch [b30e41dc1e]
- sound/soc/fsl/fsl_sai.c:
- sound/soc/fsl/fsl_sai.h:
Commit [2ea70e51eb72a] in NXP tree is now covered with commit [1ad7f52fe6]
from upstream.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
commit 85b8350ae99d1300eb6dc072459246c2649a8e50 upstream.
CAN0 and CAN1 instances share the same message ram configured
at 0x210000 on sama5d2 Linux systems.
According to current configuration of CAN0, we need 0x1c00 bytes
so that the CAN1 don't overlap its message ram:
64 x RX FIFO0 elements => 64 x 72 bytes
32 x TXE (TX Event FIFO) elements => 32 x 8 bytes
32 x TXB (TX Buffer) elements => 32 x 72 bytes
So a total of 7168 bytes (0x1C00).
Fix offset to match this needed size.
Make the CAN0 message ram ioremap match exactly this size so that is
easily understandable. Adapt CAN1 size accordingly.
Fixes: bc6d5d7666 ("ARM: dts: at91: sama5d2: add m_can nodes")
Reported-by: Dan Sneddon <dan.sneddon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Cc: stable@vger.kernel.org # v4.13+
Link: https://lore.kernel.org/r/20201203091949.9015-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3456b9fd269c6d0c973b136c5449d46b2510f4b upstream.
ARM Cortex-A57 and Cortex-A72 cores running in 32-bit mode are affected
by silicon errata #1742098 and #1655431, respectively, where the second
instruction of a AES instruction pair may execute twice if an interrupt
is taken right after the first instruction consumes an input register of
which a single 32-bit lane has been updated the last time it was modified.
This is not such a rare occurrence as it may seem: in counter mode, only
the least significant 32-bit word is incremented in the absence of a
carry, which makes our counter mode implementation susceptible to these
errata.
So let's shuffle the counter assignments around a bit so that the most
recent updates when the AES instruction pair executes are 128-bit wide.
[0] ARM-EPM-049219 v23 Cortex-A57 MPCore Software Developers Errata Notice
[1] ARM-EPM-012079 v11.0 Cortex-A72 MPCore Software Developers Errata Notice
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad2091f893bd5dfe2824f0d6819600d120698e9f ]
The Allwinner V3 SoC shares the same base as the V3s but comes with
extra pins and features available. As a result, it has its dedicated
compatible string (already used in device trees), which is added here.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201031182137.1879521-2-contact@paulk.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 656ab1bdcd2b755dc161a9774201100d5bf74b8d ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: a2c6e82e53 ("ARM: dts: meson: switch to the generic Ethernet PHY reset bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # on Odroid-C1+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/ff78772b306411e145769c46d4090554344db41e.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
Primoz Fiser