[ Upstream commit 6553896666433e7efec589838b400a2a652b3ffa ]
Some code pathes, especially the low level entry code, must be protected
against instrumentation for various reasons:
- Low level entry code can be a fragile beast, especially on x86.
- With NO_HZ_FULL RCU state needs to be established before using it.
Having a dedicated section for such code allows to validate with tooling
that no unsafe functions are invoked.
Add the .noinstr.text section and the noinstr attribute to mark
functions. noinstr implies notrace. Kprobes will gain a section check
later.
Provide also a set of markers: instrumentation_begin()/end()
These are used to mark code inside a noinstr function which calls
into regular instrumentable text section as safe.
The instrumentation markers are only active when CONFIG_DEBUG_ENTRY is
enabled as the end marker emits a NOP to prevent the compiler from merging
the annotation points. This means the objtool verification requires a
kernel compiled with this option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200505134100.075416272@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d62e81b60d4025e2dfcd5ea531cc1394ce9226f ]
Giancarlo Ferrari reports the following oops while trying to use kexec:
Unable to handle kernel paging request at virtual address 80112f38
pgd = fd7ef03e
[80112f38] *pgd=0001141e(bad)
Internal error: Oops: 80d [#1] PREEMPT SMP ARM
...
This is caused by machine_kexec() trying to set the kernel text to be
read/write, so it can poke values into the relocation code before
copying it - and an interrupt occuring which changes the page tables.
The subsequent writes then hit read-only sections that trigger a
data abort resulting in the above oops.
Fix this by copying the relocation code, and then writing the variables
into the destination, thereby avoiding the need to make the kernel text
read/write.
Reported-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com>
Tested-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c698bff66ab4914bb3d71da7dc6112519bde23e ]
Ensure that the signal page contains our poison instruction to increase
the protection against ROP attacks and also contains well defined
contents.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5638159f6d93b99ec9743ac7f65563fca3cf413d ]
This reverts commit c17e9377aa.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 388c705b95f23f317fa43e6abf9ff07b583b721a ]
This reverts commit 6d4d273588378c65915acaf7b2ee74e9dd9c130a.
bfq.limit_depth passes word_depths[] as shallow_depth down to sbitmap core
sbitmap_get_shallow, which uses just the number to limit the scan depth of
each bitmap word, formula:
scan_percentage_for_each_word = shallow_depth / (1 << sbimap->shift) * 100%
That means the comments's percentiles 50%, 75%, 18%, 37% of bfq are correct.
But after commit patch 'bfq: Fix computation of shallow depth', we use
sbitmap.depth instead, as a example in following case:
sbitmap.depth = 256, map_nr = 4, shift = 6; sbitmap_word.depth = 64.
The resulsts of computed bfqd->word_depths[] are {128, 192, 48, 96}, and
three of the numbers exceed core dirver's 'sbitmap_word.depth=64' limit
nothing.
Signed-off-by: Lin Feng <linf@wangsu.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab543823322b564f205cb15d0f0302803c87d11 ]
virt_addr_valid macro checks that a virtual address is valid, ie that
the address belongs to the linear mapping and that the corresponding
physical page exists.
Add the missing check that ensures the virtual address belongs to the
linear mapping, otherwise __virt_to_phys, when compiled with
CONFIG_DEBUG_VIRTUAL enabled, raises a WARN that is interpreted as a
kernel bug by syzbot.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e92bb0fa75bca9a57e4aba2e36f67d8016a3053 ]
[why]
An old dc_sink state is causing a memory leak because it is missing a
dc_sink_release before a new dc_sink is assigned back to
aconnector->dc_sink.
[how]
Decrement the dc_sink refcount before reassigning it to a new dc_sink.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2abaa323d744011982b20b8f3886184d56d23946 ]
[why]
drm_atomic_commit was changed so that the caller must free their
drm_atomic_state reference on successes.
[how]
Add drm_atomic_commit_put after drm_atomic_commit call in
dm_force_atomic_commit.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ddc818d9bb877c64f5c649beab97af86c403702 ]
[why]
prev_sink is not used anywhere else in the function and the reference to
it from dc_link is replaced with a new dc_sink.
[how]
Change dc_sink_retain(prev_sink) to dc_sink_release(prev_sink).
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1622711beebe887e4f0f8237fea1f09bb48e9a51 ]
[WHY]
When enabling HDMI on ComboPHY, there are not
enough clock sources to complete display detection.
[HOW]
Initialize more clock sources.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9e95c39280530200cdd0bbd2670e6334a81970b ]
Tested both with Corsairs firmware 11.3 and 13.0 for the Corsairs MP600
and both have the issue as reported by the kernel.
nvme nvme0: missing or invalid SUBNQN field.
Signed-off-by: Claus Stovgaard <claus.stovgaard@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03fedf93593c82538b18476d8c4f0e8f8435ea70 ]
When inode has no listxattr op of its own (e.g. squashfs) vfs_listxattr
calls the LSM inode_listsecurity hooks to list the xattrs that LSMs will
intercept in inode_getxattr hooks.
When selinux LSM is installed but not initialized, it will list the
security.selinux xattr in inode_listsecurity, but will not intercept it
in inode_getxattr. This results in -ENODATA for a getxattr call for an
xattr returned by listxattr.
This situation was manifested as overlayfs failure to copy up lower
files from squashfs when selinux is built-in but not initialized,
because ovl_copy_xattr() iterates the lower inode xattrs by
vfs_listxattr() and vfs_getxattr().
ovl_copy_xattr() skips copy up of security labels that are indentified by
inode_copy_up_xattr LSM hooks, but it does that after vfs_getxattr().
Since we are not going to copy them, skip vfs_getxattr() of the security
labels.
Reported-by: Michael Labriola <michael.d.labriola@gmail.com>
Tested-by: Michael Labriola <michael.d.labriola@gmail.com>
Link: https://lore.kernel.org/linux-unionfs/2nv9d47zt7.fsf@aldarion.sourceruckus.org/
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2b00be488730522d0fb7a8a5de663febdcefe0a ]
If a capability is stored on disk in v2 format cap_inode_getsecurity() will
currently return in v2 format unconditionally.
This is wrong: v2 cap should be equivalent to a v3 cap with zero rootid,
and so the same conversions performed on it.
If the rootid cannot be mapped, v3 is returned unconverted. Fix this so
that both v2 and v3 return -EOVERFLOW if the rootid (or the owner of the fs
user namespace in case of v2) cannot be mapped into the current user
namespace.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554677b97257b0b69378bd74e521edb7e94769ff ]
The vfs_getxattr() in ovl_xattr_set() is used to check whether an xattr
exist on a lower layer file that is to be removed. If the xattr does not
exist, then no need to copy up the file.
This call of vfs_getxattr() wasn't wrapped in credential override, and this
is probably okay. But for consitency wrap this instance as well.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67fbe02a5cebc3c653610f12e3c0424e58450153 ]
Recently userspace has started making more use of SW_TABLET_MODE
(when an input-dev reports this).
Specifically recent GNOME3 versions will:
1. When SW_TABLET_MODE is reported and is reporting 0:
1.1 Disable accelerometer-based screen auto-rotation
1.2 Disable automatically showing the on-screen keyboard when a
text-input field is focussed
2. When SW_TABLET_MODE is reported and is reporting 1:
2.1 Ignore input-events from the builtin keyboard and touchpad
(this is for 360° hinges style 2-in-1s where the keyboard and
touchpads are accessible on the back of the tablet when folded
into tablet-mode)
This means that claiming to support SW_TABLET_MODE when it does not
actually work / reports correct values has bad side-effects.
The check in the hp-wmi code which is used to decide if the input-dev
should claim SW_TABLET_MODE support, only checks if the
HPWMI_HARDWARE_QUERY is supported. It does *not* check if the hardware
actually is capable of reporting SW_TABLET_MODE.
This leads to the hp-wmi input-dev claiming SW_TABLET_MODE support,
while in reality it will always report 0 as SW_TABLET_MODE value.
This has been seen on a "HP ENVY x360 Convertible 15-cp0xxx" and
this likely is the case on a whole lot of other HP models.
This problem causes both auto-rotation and on-screen keyboard
support to not work on affected x360 models.
There is no easy fix for this, but since userspace expects
SW_TABLET_MODE reporting to be reliable when advertised it is
better to not claim/report SW_TABLET_MODE support at all, then
to claim to support it while it does not work.
To avoid the mentioned problems, add a new enable_tablet_mode_sw
module-parameter which defaults to false.
Note I've made this an int using the standard -1=auto, 0=off, 1=on
triplett, with the hope that in the future we can come up with a
better way to detect SW_TABLET_MODE support. ATM the default
auto option just does the same as off.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1918255
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20210120124941.73409-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06862d789ddde8a99c1e579e934ca17c15a84755 ]
We get suspcious RCU usage splats with cpuidle in several places in
omap_enter_idle_coupled() with the kernel debug options enabled:
RCU used illegally from extended quiescent state!
...
(_raw_spin_lock_irqsave)
(omap_enter_idle_coupled+0x17c/0x2d8)
(omap_enter_idle_coupled)
(cpuidle_enter_state)
(cpuidle_enter_state_coupled)
(cpuidle_enter)
Let's use RCU_NONIDLE to suppress these splats. Things got changed around
with commit 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the
idle path") that started triggering these warnings.
For the tick_broadcast related calls, ideally we'd just switch over to
using CPUIDLE_FLAG_TIMER_STOP for omap_enter_idle_coupled() to have the
generic cpuidle code handle the tick_broadcast related calls for us and
then just drop the tick_broadcast calls here.
But we're currently missing the call in the common cpuidle code for
tick_broadcast_enable() that CPU1 hotplug needs as described in earlier
commit 50d6b3cf94 ("ARM: OMAP2+: fix lack of timer interrupts on CPU1
after hotplug").
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93f2a11580a9732c1d90f9e01a7e9facc825658f ]
The GCC_LPASS_Q6_AXI_CLK and GCC_LPASS_SWAY_CLK clocks may not be
touched on a typical UEFI based SDM845 device, but when the kernel is
built with CONFIG_SDM_LPASSCC_845 this happens, unless they are marked
as protected-clocks in the DT.
This was done for the MTP and the Pocophone, but not for DB845c and the
Lenovo Yoga C630 - causing these to fail to boot if the LPASS clock
controller is enabled (which it typically isn't).
Tested-by: Vinod Koul <vkoul@kernel.org> #on db845c
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201222001103.3112306-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43f20b1c6140896916f4e91aacc166830a7ba849 ]
It recently became apparent that the lack of a 'device_type = "pci"'
in the PCIe root complex node for rk3399 is a violation of the PCI
binding, as documented in IEEE Std 1275-1994. Changes to the kernel's
parsing of the DT made such violation fatal, as drivers cannot
probe the controller anymore.
Add the missing property makes the PCIe node compliant. While we
are at it, drop the pointless linux,pci-domain property, which only
makes sense when there are multiple host bridges.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200815125112.462652-3-maz@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 385aac1519417b89cb91b77c22e4ca21db563cd0 upstream.
Fix NULL pointer dereference when adding new psi monitor to the root
cgroup. PSI files for root cgroup was introduced in df5ba5be74 by using
system wide psi struct when reading, but file write/monitor was not
properly fixed. Since the PSI config for the root cgroup isn't
initialized, the current implementation tries to lock a NULL ptr,
resulting in a crash.
Can be triggered by running this as root:
$ tee /sys/fs/cgroup/cpu.pressure <<< "some 10000 1000000"
Signed-off-by: Odin Ugedal <odin@uged.al>
Reviewed-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Dan Schatzberg <dschatzberg@fb.com>
Fixes: df5ba5be74 ("kernel/sched/psi.c: expose pressure metrics on root cgroup")
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org # 5.2+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4295ab0b485b8bc50d2264bcae2acd06f25caaf upstream.
After Commit 3499ba8198cad ("xen: Fix event channel callback via
INTX/GSI"), xenbus_probe() will be called too early on Arm. This will
recent to a guest hang during boot.
If the hang wasn't there, we would have ended up to call
xenbus_probe() twice (the second time is in xenbus_probe_initcall()).
We don't need to initialize xenbus_probe() early for Arm guest.
Therefore, the call in xen_guest_init() is now removed.
After this change, there is no more external caller for xenbus_probe().
So the function is turned to a static one. Interestingly there were two
prototypes for it.
Cc: stable@vger.kernel.org
Fixes: 3499ba8198cad ("xen: Fix event channel callback via INTX/GSI")
Reported-by: Ian Jackson <iwj@xenproject.org>
Signed-off-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20210210170654.5377-1-julien@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b220c049d5196dd94d992dd2dc8cba1a5e6123bf upstream.
When filters are used by trace events, a page is allocated on each CPU and
used to copy the trace event fields to this page before writing to the ring
buffer. The reason to use the filter and not write directly into the ring
buffer is because a filter may discard the event and there's more overhead
on discarding from the ring buffer than the extra copy.
The problem here is that there is no check against the size being allocated
when using this page. If an event asks for more than a page size while being
filtered, it will get only a page, leading to the caller writing more that
what was allocated.
Check the length of the request, and if it is more than PAGE_SIZE minus the
header default back to allocating from the ring buffer directly. The ring
buffer may reject the event if its too big anyway, but it wont overflow.
Link: https://lore.kernel.org/ath10k/1612839593-2308-1-git-send-email-wgong@codeaurora.org/
Cc: stable@vger.kernel.org
Fixes: 0fc1b09ff1 ("tracing: Use temp buffer when filtering events")
Reported-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 256cfdd6fdf70c6fcf0f7c8ddb0ebd73ce8f3bc9 upstream.
The file /sys/kernel/tracing/events/enable is used to enable all events by
echoing in "1", or disabling all events when echoing in "0". To know if all
events are enabled, disabled, or some are enabled but not all of them,
cating the file should show either "1" (all enabled), "0" (all disabled), or
"X" (some enabled but not all of them). This works the same as the "enable"
files in the individule system directories (like tracing/events/sched/enable).
But when all events are enabled, the top level "enable" file shows "X". The
reason is that its checking the "ftrace" events, which are special events
that only exist for their format files. These include the format for the
function tracer events, that are enabled when the function tracer is
enabled, but not by the "enable" file. The check includes these events,
which will always be disabled, and even though all true events are enabled,
the top level "enable" file will show "X" instead of "1".
To fix this, have the check test the event's flags to see if it has the
"IGNORE_ENABLE" flag set, and if so, not test it.
Cc: stable@vger.kernel.org
Fixes: 553552ce17 ("tracing: Combine event filter_active and enable into single flags field")
Reported-by: "Yordan Karadzhov (VMware)" <y.karadz@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28dc10eb77a2db7681b08e3b109764bbe469e347 upstream.
Fixes the following warnings which results in interrupts disabled on
port B/F:
gpio gpiochip1: (B): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip5: (F): detected irqchip that is shared with multiple gpiochips: please fix the driver.
- added separate irqchip for each interrupt capable gpiochip
- provided unique names for each irqchip
Fixes: d2b0919615 ("gpio: ep93xx: Pass irqchip when adding gpiochip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b81a7ab8055d01d827ef66374b126eeac3bd108 upstream.
Two index spaces and ep93xx_gpio_port are confusing.
Instead add a separate struct to store necessary data and remove
ep93xx_gpio_port.
- add struct to store IRQ related data for each IRQ capable chip
- replace offset array with defined offsets
- add IRQ registers offset for each IRQ capable chip into
ep93xx_gpio_banks
------------[ cut here ]------------
kernel BUG at drivers/gpio/gpio-ep93xx.c:64!
---[ end trace 3f6544e133e9f5ae ]---
Fixes: fd935fc421 ("gpio: ep93xx: Do not pingpong irq numbers")
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 506220d2ba21791314af569211ffd8870b8208fa upstream.
Sysbot has reported a warning where a kmalloc() attempt exceeds the
maximum limit. This has been identified as corruption of the xattr_ids
count when reading the xattr id lookup table.
This patch adds a number of additional sanity checks to detect this
corruption and others.
1. It checks for a corrupted xattr index read from the inode. This could
be because the metadata block is uncompressed, or because the
"compression" bit has been corrupted (turning a compressed block
into an uncompressed block). This would cause an out of bounds read.
2. It checks against corruption of the xattr_ids count. This can either
lead to the above kmalloc failure, or a smaller than expected
table to be read.
3. It checks the contents of the index table for corruption.
[phillip@squashfs.org.uk: fix checkpatch issue]
Link: https://lkml.kernel.org/r/270245655.754655.1612770082682@webmail.123-reg.co.uk
Link: https://lkml.kernel.org/r/20210204130249.4495-5-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: syzbot+2ccea6339d368360800d@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eabac19e40c095543def79cb6ffeb3a8588aaff4 upstream.
Sysbot has reported an "slab-out-of-bounds read" error which has been
identified as being caused by a corrupted "ino_num" value read from the
inode. This could be because the metadata block is uncompressed, or
because the "compression" bit has been corrupted (turning a compressed
block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the inodes count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large inodes count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
[phillip@squashfs.org.uk: fix checkpatch issue]
Link: https://lkml.kernel.org/r/527909353.754618.1612769948607@webmail.123-reg.co.uk
Link: https://lkml.kernel.org/r/20210204130249.4495-4-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: syzbot+04419e3ff19d2970ea28@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f37aa4c7366e23f91b81d00bafd6a7ab54e4a381 upstream.
Sysbot has reported a number of "slab-out-of-bounds reads" and
"use-after-free read" errors which has been identified as being caused
by a corrupted index value read from the inode. This could be because
the metadata block is uncompressed, or because the "compression" bit has
been corrupted (turning a compressed block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the ids count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large ids count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
Link: https://lkml.kernel.org/r/20210204130249.4495-3-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: syzbot+b06d57ba83f604522af2@syzkaller.appspotmail.com
Reported-by: syzbot+c021ba012da41ee9807c@syzkaller.appspotmail.com
Reported-by: syzbot+5024636e8b5fd19f0f19@syzkaller.appspotmail.com
Reported-by: syzbot+bcbc661df46657d0fa4f@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19a23da53932bc8011220bd8c410cb76012de004 upstream.
Grab kvm->lock before pinning memory when registering an encrypted
region; sev_pin_memory() relies on kvm->lock being held to ensure
correctness when checking and updating the number of pinned pages.
Add a lockdep assertion to help prevent future regressions.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Fixes: 1e80fdc09d ("KVM: SVM: Pin guest memory when SEV is active")
Signed-off-by: Peter Gonda <pgonda@google.com>
V2
- Fix up patch description
- Correct file paths svm.c -> sev.c
- Add unlock of kvm->lock on sev_pin_memory error
V1
- https://lore.kernel.org/kvm/20210126185431.1824530-1-pgonda@google.com/
Message-Id: <20210127161524.2832400-1-pgonda@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e88b2c6e5a4d9ce30d75391e4d950da74bb2bd90 upstream.
While reviewing a different fix, John and I noticed an oddity in one of the
BPF program dumps that stood out, for example:
# bpftool p d x i 13
0: (b7) r0 = 808464450
1: (b4) w4 = 808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
[...]
In line 2 we noticed that the mov32 would 32 bit truncate the original src
register for the div/mod operation. While for the two operations the dst
register is typically marked unknown e.g. from adjust_scalar_min_max_vals()
the src register is not, and thus verifier keeps tracking original bounds,
simplified:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = -1
1: R0_w=invP-1 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (b7) r1 = -1
2: R0_w=invP-1 R1_w=invP-1 R10=fp0
2: (3c) w0 /= w1
3: R0_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R1_w=invP-1 R10=fp0
3: (77) r1 >>= 32
4: R0_w=invP(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff)) R1_w=invP4294967295 R10=fp0
4: (bf) r0 = r1
5: R0_w=invP4294967295 R1_w=invP4294967295 R10=fp0
5: (95) exit
processed 6 insns (limit 1000000) max_states_per_insn 0 total_states 0 peak_states 0 mark_read 0
Runtime result of r0 at exit is 0 instead of expected -1. Remove the
verifier mov32 src rewrite in div/mod and replace it with a jmp32 test
instead. After the fix, we result in the following code generation when
having dividend r1 and divisor r6:
div, 64 bit: div, 32 bit:
0: (b7) r6 = 8 0: (b7) r6 = 8
1: (b7) r1 = 8 1: (b7) r1 = 8
2: (55) if r6 != 0x0 goto pc+2 2: (56) if w6 != 0x0 goto pc+2
3: (ac) w1 ^= w1 3: (ac) w1 ^= w1
4: (05) goto pc+1 4: (05) goto pc+1
5: (3f) r1 /= r6 5: (3c) w1 /= w6
6: (b7) r0 = 0 6: (b7) r0 = 0
7: (95) exit 7: (95) exit
mod, 64 bit: mod, 32 bit:
0: (b7) r6 = 8 0: (b7) r6 = 8
1: (b7) r1 = 8 1: (b7) r1 = 8
2: (15) if r6 == 0x0 goto pc+1 2: (16) if w6 == 0x0 goto pc+1
3: (9f) r1 %= r6 3: (9c) w1 %= w6
4: (b7) r0 = 0 4: (b7) r0 = 0
5: (95) exit 5: (95) exit
x86 in particular can throw a 'divide error' exception for div
instruction not only for divisor being zero, but also for the case
when the quotient is too large for the designated register. For the
edx:eax and rdx:rax dividend pair it is not an issue in x86 BPF JIT
since we always zero edx (rdx). Hence really the only protection
needed is against divisor being zero.
Fixes: 68fda450a7 ("bpf: fix 32-bit divide by zero")
Co-developed-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14a71d509ac809dcf56d7e3ca376b15d17bd0ddd ]
With commit eaa7995c529b54 (regulator: core: avoid
regulator_resolve_supply() race condition) we started holding the rdev
lock while resolving supplies, an operation that requires holding the
regulator_list_mutex. This results in lockdep warnings since in other
places we take the list mutex then the mutex on an individual rdev.
Since the goal is to make sure that we don't call set_supply() twice
rather than a concern about the cost of resolution pull the rdev lock
and check for duplicate resolution down to immediately before we do the
set_supply() and drop it again once the allocation is done.
Fixes: eaa7995c529b54 (regulator: core: avoid regulator_resolve_supply() race condition)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122132042.10306-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c635caef410aa757befbd8857c1eadde5cc22ed ]
On !PREEMPT kernel, we can get below softlockup when doing stress
testing with creating and destroying block cgroup repeatly. The
reason is it may take a long time to acquire the queue's lock in
the loop of blkcg_destroy_blkgs(), or the system can accumulate a
huge number of blkgs in pathological cases. We can add a need_resched()
check on each loop and release locks and do cond_resched() if true
to avoid this issue, since the blkcg_destroy_blkgs() is not called
from atomic contexts.
[ 4757.010308] watchdog: BUG: soft lockup - CPU#11 stuck for 94s!
[ 4757.010698] Call trace:
[ 4757.010700] blkcg_destroy_blkgs+0x68/0x150
[ 4757.010701] cgwb_release_workfn+0x104/0x158
[ 4757.010702] process_one_work+0x1bc/0x3f0
[ 4757.010704] worker_thread+0x164/0x468
[ 4757.010705] kthread+0x108/0x138
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de96c3943f591018727b862f51953c1b6c55bcc3 ]
Some i2c device driver indirectly uses I2C driver when it is now
being suspended. The i2c devices driver is suspended during the
NOIRQ phase and this cannot be changed due to other dependencies.
Therefore, we also need to move the suspend handling for the I2C
controller driver to the NOIRQ phase as well.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba6dfce47c4d002d96cd02a304132fca76981172 ]
Remove duplicated helper functions to parse opaque XDR objects
and place inside new file net/sunrpc/auth_gss/auth_gss_internal.h.
In the new file carry the license and copyright from the source file
net/sunrpc/auth_gss/auth_gss.c. Finally, update the comment inside
include/linux/sunrpc/xdr.h since lockd is not the only user of
struct xdr_netobj.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a21b1d4a728a483f07c638ccd8610d4b4f12684 ]
If we get into a problem severe enough to attempt a reprobe,
we schedule a worker to do that. However, if the problem gets
more severe and the device is actually destroyed before this
worker has a chance to run, we use a free device. Bump up the
reference count of the device until the worker runs to avoid
this situation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.871f0892e4b2.I94819e11afd68d875f3e242b98bef724b8236f1e@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e223e42aac30bf81f9302c676cdf58cf2bf36950 ]
Having sta_id not set for aux_sta and snif_sta can potentially lead to a
hard to debug issue in case remove station is called without an add. In
this case sta_id 0, an unrelated regular station, will be removed.
In fact, we do have a FW assert that occures rarely and from the debug
data analysis it looks like sta_id 0 is removed by mistake, though it's
hard to pinpoint the exact flow. The WARN_ON in this patch should help
to find it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5dc6dd9b22d5.I2add1b5ad24d0d0a221de79d439c09f88fcaf15d@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d6bc752cc2806366d9a4fd577b3f6c1f7a7e04e ]
If the image loader allocation fails, we leak all the previously
allocated memory. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.97172cbaa67c.I3473233d0ad01a71aa9400832fb2b9f494d88a11@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98c7d21f957b10d9c07a3a60a3a5a8f326a197e5 ]
I hit a NULL pointer exception in this function when the
init flow went really bad.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.2e8da9f2c132.I0234d4b8ddaf70aaa5028a20c863255e05bc1f84@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c56d862c749669d45c256f581eac4244be00d4d ]
We need to take the mutex to call iwl_mvm_get_sync_time(), do it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.4bb5ccf881a6.I62973cbb081e80aa5b0447a5c3b9c3251a65cf6b@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf544e9aa570034e094a8a40d5f9e1e2c4916d18 ]
In the new CSA flow, we remain associated during CSA, but
still do a unbind-bind to the vif. However, sending the power
command right after when vif is unbound but still associated
causes FW to assert (0x3400) since it cannot tell the LMAC id.
Just skip this command, we will send it again in a bit, when
assigning the new context.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.64a2254ac5c3.Iaa3a9050bf3d7c9cd5beaf561e932e6defc12ec3@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e953daeb68b1abd8a7d44902786349fdeef5c297 ]
Reset (aka power off) happens when the reset gpio is made active.
Change function name to ak4458_reset to match devicetree property "reset-gpios"
Signed-off-by: Eliot Blennerhassett <eliot@blennerhassett.gen.nz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/ce650f47-4ff6-e486-7846-cc3d033f3601@blennerhassett.gen.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08bd8dbe88825760e953759d7ec212903a026c75 ]
If the server returns a new stateid that does not match the one in our
cache, then try to return the one we hold instead of just invalidating
it on the client side. This ensures that both client and server will
agree that the stateid is invalid.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6011966ac6f402847eb5326beee8da3a80405c7 ]
The dst entry should be released if no neighbour is found. Goto label
free_dst to fix the issue. Besides, the check of ndev against NULL is
redundant.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210121145738.51091-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcf3c8fb32ddbfa3b8227db38aa6746405bd4527 ]
Upon receiving CSA with 160MHz extended NSS BW from associated AP,
STA should set the HT operation_mode based on new_center_freq_seg1
because it is later used as ccfs2 in ieee80211_chandef_vht_oper().
Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com>
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20201222064714.24888-1-shay.bar@celeno.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaa7995c529b54d68d97a30f6344cc6ca2f214a7 ]
The final step in regulator_register() is to call
regulator_resolve_supply() for each registered regulator
(including the one in the process of being registered). The
regulator_resolve_supply() function first checks if rdev->supply
is NULL, then it performs various steps to try to find the supply.
If successful, rdev->supply is set inside of set_supply().
This procedure can encounter a race condition if two concurrent
tasks call regulator_register() near to each other on separate CPUs
and one of the regulators has rdev->supply_name specified. There
is currently nothing guaranteeing atomicity between the rdev->supply
check and set steps. Thus, both tasks can observe rdev->supply==NULL
in their regulator_resolve_supply() calls. This then results in
both creating a struct regulator for the supply. One ends up
actually stored in rdev->supply and the other is lost (though still
present in the supply's consumer_list).
Here is a kernel log snippet showing the issue:
[ 12.421768] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.425854] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.429064] debugfs: Directory 'regulator.4-SUPPLY' with parent
'17a00000.rsc:rpmh-regulator-gfxlvl-pm8350_s5_level'
already present!
Avoid this race condition by holding the rdev->mutex lock inside
of regulator_resolve_supply() while checking and setting
rdev->supply.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Link: https://lore.kernel.org/r/1610068562-4410-1-git-send-email-collinsd@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afbc293add6466f8f3f0c3d944d85f53709c170f ]
xfrm_probe_algs() probes kernel crypto modules and changes the
availability of struct xfrm_algo_desc. But there is a small window
where ealg->available and aalg->available get changed between
count_ah_combs()/count_esp_combs() and dump_ah_combs()/dump_esp_combs(),
in this case we may allocate a smaller skb but later put a larger
amount of data and trigger the panic in skb_put().
Fix this by relaxing the checks when counting the size, that is,
skipping the test of ->available. We may waste some memory for a few
of sizeof(struct sadb_comb), but it is still much better than a panic.
Reported-by: syzbot+b2bf2652983d23734c5c@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
