mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-09-08 05:43:21 +09:00
![Frieder Schrempf](/assets/img/avatar_default.png)
In cases when the same SPL should run on boards with i.MX8MM, that differ in DDR configuration, it is necessary to try different parameters and check if the training done by the firmware suceeds or not. Therefore we return the DDR training/initialization success to the upper layer in order to be able to retry with different settings if necessary. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
176 lines
4.9 KiB
C
176 lines
4.9 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2018-2019 NXP
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <errno.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/ddr.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
|
|
void ddr_cfg_umctl2(struct dram_cfg_param *ddrc_cfg, int num)
|
|
{
|
|
int i = 0;
|
|
|
|
for (i = 0; i < num; i++) {
|
|
reg32_write(ddrc_cfg->reg, ddrc_cfg->val);
|
|
ddrc_cfg++;
|
|
}
|
|
}
|
|
|
|
int ddr_init(struct dram_timing_info *dram_timing)
|
|
{
|
|
unsigned int tmp, initial_drate, target_freq;
|
|
int ret;
|
|
|
|
debug("DDRINFO: start DRAM init\n");
|
|
|
|
/* Step1: Follow the power up procedure */
|
|
if (is_imx8mq()) {
|
|
reg32_write(SRC_DDRC_RCR_ADDR + 0x04, 0x8F00000F);
|
|
reg32_write(SRC_DDRC_RCR_ADDR, 0x8F00000F);
|
|
reg32_write(SRC_DDRC_RCR_ADDR + 0x04, 0x8F000000);
|
|
} else {
|
|
reg32_write(SRC_DDRC_RCR_ADDR, 0x8F00001F);
|
|
reg32_write(SRC_DDRC_RCR_ADDR, 0x8F00000F);
|
|
}
|
|
|
|
debug("DDRINFO: cfg clk\n");
|
|
/* change the clock source of dram_apb_clk_root: source 4 800MHz /4 = 200MHz */
|
|
clock_set_target_val(DRAM_APB_CLK_ROOT, CLK_ROOT_ON | CLK_ROOT_SOURCE_SEL(4) |
|
|
CLK_ROOT_PRE_DIV(CLK_ROOT_PRE_DIV4));
|
|
|
|
/* disable iso */
|
|
reg32_write(0x303A00EC, 0x0000ffff); /* PGC_CPU_MAPPING */
|
|
reg32setbit(0x303A00F8, 5); /* PU_PGC_SW_PUP_REQ */
|
|
|
|
initial_drate = dram_timing->fsp_msg[0].drate;
|
|
/* default to the frequency point 0 clock */
|
|
ddrphy_init_set_dfi_clk(initial_drate);
|
|
|
|
/* D-aasert the presetn */
|
|
reg32_write(SRC_DDRC_RCR_ADDR, 0x8F000006);
|
|
|
|
/* Step2: Program the dwc_ddr_umctl2 registers */
|
|
debug("DDRINFO: ddrc config start\n");
|
|
ddr_cfg_umctl2(dram_timing->ddrc_cfg, dram_timing->ddrc_cfg_num);
|
|
debug("DDRINFO: ddrc config done\n");
|
|
|
|
/* Step3: De-assert reset signal(core_ddrc_rstn & aresetn_n) */
|
|
reg32_write(SRC_DDRC_RCR_ADDR, 0x8F000004);
|
|
reg32_write(SRC_DDRC_RCR_ADDR, 0x8F000000);
|
|
|
|
/*
|
|
* Step4: Disable auto-refreshes, self-refresh, powerdown, and
|
|
* assertion of dfi_dram_clk_disable by setting RFSHCTL3.dis_auto_refresh = 1,
|
|
* PWRCTL.powerdown_en = 0, and PWRCTL.selfref_en = 0, PWRCTL.en_dfi_dram_clk_disable = 0
|
|
*/
|
|
reg32_write(DDRC_DBG1(0), 0x00000000);
|
|
reg32_write(DDRC_RFSHCTL3(0), 0x0000001);
|
|
reg32_write(DDRC_PWRCTL(0), 0xa0);
|
|
|
|
/* if ddr type is LPDDR4, do it */
|
|
tmp = reg32_read(DDRC_MSTR(0));
|
|
if (tmp & (0x1 << 5))
|
|
reg32_write(DDRC_DDR_SS_GPR0, 0x01); /* LPDDR4 mode */
|
|
|
|
/* determine the initial boot frequency */
|
|
target_freq = reg32_read(DDRC_MSTR2(0)) & 0x3;
|
|
target_freq = (tmp & (0x1 << 29)) ? target_freq : 0x0;
|
|
|
|
/* Step5: Set SWCT.sw_done to 0 */
|
|
reg32_write(DDRC_SWCTL(0), 0x00000000);
|
|
|
|
/* Set the default boot frequency point */
|
|
clrsetbits_le32(DDRC_DFIMISC(0), (0x1f << 8), target_freq << 8);
|
|
/* Step6: Set DFIMISC.dfi_init_complete_en to 0 */
|
|
clrbits_le32(DDRC_DFIMISC(0), 0x1);
|
|
|
|
/* Step7: Set SWCTL.sw_done to 1; need to polling SWSTAT.sw_done_ack */
|
|
reg32_write(DDRC_SWCTL(0), 0x00000001);
|
|
do {
|
|
tmp = reg32_read(DDRC_SWSTAT(0));
|
|
} while ((tmp & 0x1) == 0x0);
|
|
|
|
/*
|
|
* Step8 ~ Step13: Start PHY initialization and training by
|
|
* accessing relevant PUB registers
|
|
*/
|
|
debug("DDRINFO:ddrphy config start\n");
|
|
|
|
ret = ddr_cfg_phy(dram_timing);
|
|
if (ret)
|
|
return ret;
|
|
|
|
debug("DDRINFO: ddrphy config done\n");
|
|
|
|
/*
|
|
* step14 CalBusy.0 =1, indicates the calibrator is actively
|
|
* calibrating. Wait Calibrating done.
|
|
*/
|
|
do {
|
|
tmp = reg32_read(DDRPHY_CalBusy(0));
|
|
} while ((tmp & 0x1));
|
|
|
|
debug("DDRINFO:ddrphy calibration done\n");
|
|
|
|
/* Step15: Set SWCTL.sw_done to 0 */
|
|
reg32_write(DDRC_SWCTL(0), 0x00000000);
|
|
|
|
/* Step16: Set DFIMISC.dfi_init_start to 1 */
|
|
setbits_le32(DDRC_DFIMISC(0), (0x1 << 5));
|
|
|
|
/* Step17: Set SWCTL.sw_done to 1; need to polling SWSTAT.sw_done_ack */
|
|
reg32_write(DDRC_SWCTL(0), 0x00000001);
|
|
do {
|
|
tmp = reg32_read(DDRC_SWSTAT(0));
|
|
} while ((tmp & 0x1) == 0x0);
|
|
|
|
/* Step18: Polling DFISTAT.dfi_init_complete = 1 */
|
|
do {
|
|
tmp = reg32_read(DDRC_DFISTAT(0));
|
|
} while ((tmp & 0x1) == 0x0);
|
|
|
|
/* Step19: Set SWCTL.sw_done to 0 */
|
|
reg32_write(DDRC_SWCTL(0), 0x00000000);
|
|
|
|
/* Step20: Set DFIMISC.dfi_init_start to 0 */
|
|
clrbits_le32(DDRC_DFIMISC(0), (0x1 << 5));
|
|
|
|
/* Step21: optional */
|
|
|
|
/* Step22: Set DFIMISC.dfi_init_complete_en to 1 */
|
|
setbits_le32(DDRC_DFIMISC(0), 0x1);
|
|
|
|
/* Step23: Set PWRCTL.selfref_sw to 0 */
|
|
clrbits_le32(DDRC_PWRCTL(0), (0x1 << 5));
|
|
|
|
/* Step24: Set SWCTL.sw_done to 1; need polling SWSTAT.sw_done_ack */
|
|
reg32_write(DDRC_SWCTL(0), 0x00000001);
|
|
do {
|
|
tmp = reg32_read(DDRC_SWSTAT(0));
|
|
} while ((tmp & 0x1) == 0x0);
|
|
|
|
/* Step25: Wait for dwc_ddr_umctl2 to move to normal operating mode by monitoring
|
|
* STAT.operating_mode signal */
|
|
do {
|
|
tmp = reg32_read(DDRC_STAT(0));
|
|
} while ((tmp & 0x3) != 0x1);
|
|
|
|
/* Step26: Set back register in Step4 to the original values if desired */
|
|
reg32_write(DDRC_RFSHCTL3(0), 0x0000000);
|
|
/* enable selfref_en by default */
|
|
setbits_le32(DDRC_PWRCTL(0), 0x1 << 3);
|
|
|
|
/* enable port 0 */
|
|
reg32_write(DDRC_PCTRL_0(0), 0x00000001);
|
|
debug("DDRINFO: ddrmix config done\n");
|
|
|
|
/* save the dram timing config into memory */
|
|
dram_config_save(dram_timing, CONFIG_SAVED_DRAM_TIMING_BASE);
|
|
|
|
return 0;
|
|
}
|