mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-20 08:58:52 +09:00
![Tom Rini](/assets/img/avatar_default.png)
The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
552 lines
17 KiB
C
552 lines
17 KiB
C
/*
|
|
* Copyright 2009-2010,2012 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/* The P2020COME board is only booted via the Freescale On-Chip ROM */
|
|
#define CONFIG_SYS_RAMBOOT
|
|
#define CONFIG_SYS_EXTRA_ENV_RELOC
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xf8f80000
|
|
#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc
|
|
|
|
#ifdef CONFIG_SDCARD
|
|
#define CONFIG_RAMBOOT_SDCARD 1
|
|
#endif
|
|
|
|
#ifdef CONFIG_SPIFLASH
|
|
#define CONFIG_RAMBOOT_SPIFLASH 1
|
|
#endif
|
|
|
|
#ifndef CONFIG_SYS_MONITOR_BASE
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
#endif
|
|
|
|
/* High Level Configuration Options */
|
|
#define CONFIG_BOOKE 1 /* BOOKE */
|
|
#define CONFIG_E500 1 /* BOOKE e500 family */
|
|
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/P1020/P2020,etc*/
|
|
#define CONFIG_P2020 1
|
|
#define CONFIG_P2020COME 1
|
|
#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */
|
|
#define CONFIG_MP
|
|
|
|
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
|
|
#if defined(CONFIG_PCI)
|
|
#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */
|
|
#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */
|
|
#define CONFIG_PCIE3 1 /* PCIE controller 3 (slot 3) */
|
|
|
|
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
|
|
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
|
|
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
|
|
#endif /* #if defined(CONFIG_PCI) */
|
|
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
|
|
#define CONFIG_TSEC_ENET /* tsec ethernet support */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#if defined(CONFIG_PCI)
|
|
#define CONFIG_E1000 1 /* E1000 pci Ethernet card */
|
|
#endif
|
|
|
|
#ifndef __ASSEMBLY__
|
|
extern unsigned long get_board_ddr_clk(unsigned long dummy);
|
|
extern unsigned long get_board_sys_clk(unsigned long dummy);
|
|
#endif
|
|
|
|
/*
|
|
* For P2020COME DDRCLK and SYSCLK are from the same oscillator
|
|
* For DA phase the SYSCLK is 66MHz
|
|
* For EA phase the SYSCLK is 100MHz
|
|
*/
|
|
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0)
|
|
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
|
|
|
|
#define CONFIG_HWCONFIG
|
|
|
|
/*
|
|
* These can be toggled for performance analysis, otherwise use default.
|
|
*/
|
|
#define CONFIG_L2_CACHE /* toggle L2 cache */
|
|
#define CONFIG_BTB /* toggle branch prediction */
|
|
|
|
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
|
|
|
|
#define CONFIG_ENABLE_36BIT_PHYS 1
|
|
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_ADDR_MAP 1
|
|
#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
|
|
#define CONFIG_PANIC_HANG /* do not reset board on panic */
|
|
|
|
/*
|
|
* Config the L2 Cache as L2 SRAM
|
|
*/
|
|
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull
|
|
#else
|
|
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
|
|
#endif
|
|
#define CONFIG_SYS_L2_SIZE (512 << 10)
|
|
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR \
|
|
+ CONFIG_SYS_L2_SIZE)
|
|
|
|
#define CONFIG_SYS_CCSRBAR 0xffe00000
|
|
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
|
|
|
|
/* DDR Setup */
|
|
#define CONFIG_FSL_DDR3
|
|
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
|
|
#define CONFIG_DDR_SPD
|
|
|
|
#define CONFIG_DDR_ECC
|
|
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
|
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
|
|
|
#define CONFIG_SYS_SDRAM_SIZE 2048ULL /* DDR size on P2020COME */
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
|
|
#define CONFIG_NUM_DDR_CONTROLLERS 1
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL 2
|
|
|
|
#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
|
|
#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
|
|
#define CONFIG_SYS_DDR_SBE 0x00ff0000
|
|
|
|
#define CONFIG_SYS_SPD_BUS_NUM 1
|
|
#define SPD_EEPROM_ADDRESS 0x53
|
|
|
|
/*
|
|
* Memory map
|
|
*
|
|
* 0x0000_0000 0x7fff_ffff DDR3 2G Cacheable
|
|
* 0x8000_0000 0x9fff_ffff PCI Express 3 Mem 1G non-cacheable
|
|
* 0xa000_0000 0xbfff_ffff PCI Express 2 Mem 1G non-cacheable
|
|
* 0xc000_0000 0xdfff_ffff PCI Express 1 Mem 1G non-cacheable
|
|
* 0xffc1_0000 0xffc1_ffff PCI Express 3 IO 64K non-cacheable
|
|
* 0xffc2_0000 0xffc2_ffff PCI Express 2 IO 64K non-cacheable
|
|
* 0xffc3_0000 0xffc3_ffff PCI Express 1 IO 64K non-cacheable
|
|
*
|
|
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
|
|
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
|
|
*/
|
|
|
|
/*
|
|
* Local Bus Definitions
|
|
*/
|
|
|
|
/* There is no NOR Flash on P2020COME */
|
|
#define CONFIG_SYS_NO_FLASH
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
|
|
#define CONFIG_HWCONFIG
|
|
|
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
|
|
#ifdef CONFIG_PHYS_64BIT
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
|
|
/* the assembler doesn't like typecast */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
|
|
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
|
|
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
|
|
#else
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
|
|
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
|
|
#endif
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
|
|
- GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
|
|
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
|
|
|
|
/* Serial Port - controlled on board with jumper J8
|
|
* open - index 2
|
|
* shorted - index 1
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
|
|
|
|
/* Use the HUSH parser */
|
|
#define CONFIG_SYS_HUSH_PARSER
|
|
|
|
/*
|
|
* Pass open firmware flat tree
|
|
*/
|
|
#define CONFIG_OF_LIBFDT 1
|
|
#define CONFIG_OF_BOARD_SETUP 1
|
|
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
|
|
|
|
/* new uImage format support */
|
|
#define CONFIG_FIT 1
|
|
#define CONFIG_FIT_VERBOSE 1
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_FSL
|
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
|
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
|
|
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
|
|
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
|
|
|
|
/*
|
|
* I2C2 EEPROM
|
|
*/
|
|
#define CONFIG_ID_EEPROM
|
|
#ifdef CONFIG_ID_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_NXID
|
|
#endif
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR2 0x18
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
|
|
|
|
/*
|
|
* eSPI - Enhanced SPI
|
|
*/
|
|
#define CONFIG_FSL_ESPI
|
|
#define CONFIG_SPI_FLASH
|
|
#define CONFIG_SPI_FLASH_STMICRO
|
|
#define CONFIG_CMD_SF
|
|
#define CONFIG_SF_DEFAULT_SPEED 10000000
|
|
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
|
|
|
|
/*
|
|
* General PCI
|
|
* Memory space is mapped 1-1, but I/O space must start from 0.
|
|
*/
|
|
#if defined(CONFIG_PCI)
|
|
|
|
/* controller 3, Slot 3, tgtid 3, Base address 8000 */
|
|
#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
|
|
#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
|
|
#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
|
|
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc10000
|
|
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc10000
|
|
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
/* controller 2, Slot 2, tgtid 2, Base address 9000 */
|
|
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000
|
|
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000
|
|
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
/* controller 1, Slot 1, tgtid 1, Base address a000 */
|
|
#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
|
|
#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc30000
|
|
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc30000
|
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
|
|
|
|
#define CONFIG_PCI_PNP /* do pci plug-and-play */
|
|
|
|
#undef CONFIG_EEPRO100
|
|
#undef CONFIG_TULIP
|
|
#undef CONFIG_RTL8139
|
|
|
|
#ifdef CONFIG_RTL8139
|
|
/* This macro is used by RTL8139 but not defined in PPC architecture */
|
|
#define KSEG1ADDR(x) (x)
|
|
#define _IO_BASE 0x00000000
|
|
#endif
|
|
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
#endif /* CONFIG_PCI */
|
|
|
|
#if defined(CONFIG_TSEC_ENET)
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
|
|
#define CONFIG_TSEC1 1
|
|
#define CONFIG_TSEC1_NAME "eTSEC1"
|
|
#define CONFIG_TSEC2 1
|
|
#define CONFIG_TSEC2_NAME "eTSEC2"
|
|
#define CONFIG_TSEC3 1
|
|
#define CONFIG_TSEC3_NAME "eTSEC3"
|
|
|
|
#define TSEC1_PHY_ADDR 0
|
|
#define TSEC2_PHY_ADDR 2
|
|
#define TSEC3_PHY_ADDR 1
|
|
|
|
#undef CONFIG_VSC7385_ENET
|
|
|
|
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
|
|
#define TSEC1_PHYIDX 0
|
|
#define TSEC2_PHYIDX 0
|
|
#define TSEC3_PHYIDX 0
|
|
|
|
#define CONFIG_ETHPRIME "eTSEC1"
|
|
|
|
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
|
|
|
|
#endif /* CONFIG_TSEC_ENET */
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#if defined(CONFIG_RAMBOOT_SDCARD)
|
|
#define CONFIG_ENV_IS_IN_MMC 1
|
|
#define CONFIG_FSL_FIXED_MMC_LOCATION
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
#elif defined(CONFIG_RAMBOOT_SPIFLASH)
|
|
#define CONFIG_ENV_IS_IN_SPI_FLASH
|
|
#define CONFIG_ENV_SPI_BUS 0
|
|
#define CONFIG_ENV_SPI_CS 0
|
|
#define CONFIG_ENV_SPI_MAX_HZ 10000000
|
|
#define CONFIG_ENV_SPI_MODE 0
|
|
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#endif
|
|
|
|
#define CONFIG_LOADS_ECHO 1
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_SETEXPR
|
|
#define CONFIG_CMD_REGINFO
|
|
|
|
#if defined(CONFIG_PCI)
|
|
#define CONFIG_CMD_NET
|
|
#define CONFIG_CMD_PCI
|
|
#endif
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
#define CONFIG_MMC 1
|
|
|
|
#ifdef CONFIG_MMC
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
|
|
#define CONFIG_CMD_MMC
|
|
#define CONFIG_DOS_PARTITION
|
|
#define CONFIG_FSL_ESDHC
|
|
#define CONFIG_GENERIC_MMC
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
|
|
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
|
|
#endif /* CONFIG_MMC */
|
|
|
|
#define CONFIG_HAS_FSL_DR_USB
|
|
#ifdef CONFIG_HAS_FSL_DR_USB
|
|
#define CONFIG_USB_EHCI
|
|
|
|
#ifdef CONFIG_USB_EHCI
|
|
#define CONFIG_CMD_USB
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
#define CONFIG_USB_EHCI_FSL
|
|
#define CONFIG_USB_STORAGE
|
|
#endif
|
|
#endif
|
|
|
|
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
|
|
#define CONFIG_CMD_EXT2
|
|
#define CONFIG_CMD_FAT
|
|
#define CONFIG_DOS_PARTITION
|
|
#endif
|
|
|
|
/* Misc Extra Settings */
|
|
#define CONFIG_CMD_DHCP 1
|
|
|
|
#define CONFIG_CMD_DATE 1
|
|
#define CONFIG_RTC_M41T62 1
|
|
#define CONFIG_SYS_RTC_BUS_NUM 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
|
|
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 64 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (64 << 20)
|
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20)
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
|
|
#endif
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
|
|
/* The mac addresses for all ethernet interface */
|
|
#if defined(CONFIG_TSEC_ENET)
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_HAS_ETH1
|
|
#define CONFIG_HAS_ETH2
|
|
#define CONFIG_HAS_ETH3
|
|
#endif
|
|
|
|
#define CONFIG_HOSTNAME unknown
|
|
#define CONFIG_ROOTPATH "/opt/nfsroot"
|
|
#define CONFIG_BOOTFILE "uImage"
|
|
#define CONFIG_UBOOTPATH u-boot.bin
|
|
|
|
/* default location for tftp and bootm */
|
|
#define CONFIG_LOADADDR 1000000
|
|
|
|
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
|
|
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
|
|
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hwconfig=fsl_ddr:ecc=on\0" \
|
|
"bootcmd=run sdboot\0" \
|
|
"sdboot=setenv bootargs root=/dev/mmcblk0p2 rw " \
|
|
"rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
|
|
"$othbootargs; mmcinfo; " \
|
|
"ext2load mmc 0:2 $loadaddr /boot/$bootfile; " \
|
|
"ext2load mmc 0:2 $fdtaddr /boot/$fdtfile; " \
|
|
"bootm $loadaddr - $fdtaddr\0" \
|
|
"sdfatboot=setenv bootargs root=/dev/ram rw " \
|
|
"rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
|
|
"$othbootargs; mmcinfo; " \
|
|
"fatload mmc 0:1 $loadaddr $bootfile; " \
|
|
"fatload mmc 0:1 $fdtaddr $fdtfile; " \
|
|
"fatload mmc 0:1 $ramdiskaddr $ramdiskfile; " \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
|
|
"usbboot=setenv bootargs root=/dev/sda1 rw " \
|
|
"rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
|
|
"$othbootargs; " \
|
|
"usb start; " \
|
|
"ext2load usb 0:1 $loadaddr /boot/$bootfile; " \
|
|
"ext2load usb 0:1 $fdtaddr /boot/$fdtfile; " \
|
|
"bootm $loadaddr - $fdtaddr\0" \
|
|
"usbfatboot=setenv bootargs root=/dev/ram rw " \
|
|
"console=$consoledev,$baudrate $othbootargs; " \
|
|
"usb start; " \
|
|
"fatload usb 0:2 $loadaddr $bootfile; " \
|
|
"fatload usb 0:2 $fdtaddr $fdtfile; " \
|
|
"fatload usb 0:2 $ramdiskaddr $ramdiskfile; " \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
|
|
"usbext2boot=setenv bootargs root=/dev/ram rw " \
|
|
"console=$consoledev,$baudrate $othbootargs; " \
|
|
"usb start; " \
|
|
"ext2load usb 0:4 $loadaddr $bootfile; " \
|
|
"ext2load usb 0:4 $fdtaddr $fdtfile; " \
|
|
"ext2load usb 0:4 $ramdiskaddr $ramdiskfile; " \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
|
|
"upgradespi=sf probe 0; " \
|
|
"setenv startaddr 0; " \
|
|
"setenv erasesize a0000; " \
|
|
"tftp 1000000 $tftppath/$uboot_spi; " \
|
|
"sf erase $startaddr $erasesize; " \
|
|
"sf write 1000000 $startaddr $filesize; " \
|
|
"sf erase 100000 120000\0" \
|
|
"clearspienv=sf probe 0;sf erase 100000 20000\0" \
|
|
"othbootargs=ramdisk_size=700000 cache-sram-size=0x10000\0" \
|
|
"netdev=eth0\0" \
|
|
"rootdelaysecond=15\0" \
|
|
"uboot_nor=u-boot-nor.bin\0" \
|
|
"uboot_spi=u-boot-p2020.spi\0" \
|
|
"uboot_sd=u-boot-p2020.bin\0" \
|
|
"consoledev=ttyS0\0" \
|
|
"ramdiskaddr=2000000\0" \
|
|
"ramdiskfile=rootfs-dev.ext2.img\0" \
|
|
"fdtaddr=c00000\0" \
|
|
"fdtfile=uImage-2.6.32-p2020.dtb\0" \
|
|
"tftppath=p2020\0"
|
|
|
|
#define CONFIG_HDBOOT \
|
|
"setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"usb start;" \
|
|
"ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
|
|
"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=$serverip:$rootpath " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $loadaddr $tftppath/$bootfile;" \
|
|
"tftp $fdtaddr $tftppath/$fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/ram rw " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $ramdiskaddr $tftppath/$ramdiskfile;" \
|
|
"tftp $loadaddr $tftppath/$bootfile;" \
|
|
"tftp $fdtaddr $tftppath/$fdtfile;" \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
|
|
#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
|
|
|
|
#endif /* __CONFIG_H */
|