mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-23 10:28:51 +09:00
![Sylvain Lemieux](/assets/img/avatar_default.png)
Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP. The code taken from the legacy patch is: - lpc32xx SLC NAND driver (ECC layout for small page) This layout is matching the lpc32xx NAND SLC Linux Kernel driver. Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
598 lines
18 KiB
C
598 lines
18 KiB
C
/*
|
|
* LPC32xx SLC NAND flash controller driver
|
|
*
|
|
* (C) Copyright 2015 Vladimir Zapolskiy <vz@mleia.com>
|
|
*
|
|
* Hardware ECC support original source code
|
|
* Copyright (C) 2008 by NXP Semiconductors
|
|
* Author: Kevin Wells
|
|
*
|
|
* Copyright (c) 2015 Tyco Fire Protection Products.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <nand.h>
|
|
#include <linux/mtd/nand_ecc.h>
|
|
#include <asm/errno.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/config.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/dma.h>
|
|
#include <asm/arch/cpu.h>
|
|
|
|
#if defined(CONFIG_DMA_LPC32XX) && defined(CONFIG_SPL_BUILD)
|
|
#warning "DMA support in SPL image is not tested"
|
|
#endif
|
|
|
|
struct lpc32xx_nand_slc_regs {
|
|
u32 data;
|
|
u32 addr;
|
|
u32 cmd;
|
|
u32 stop;
|
|
u32 ctrl;
|
|
u32 cfg;
|
|
u32 stat;
|
|
u32 int_stat;
|
|
u32 ien;
|
|
u32 isr;
|
|
u32 icr;
|
|
u32 tac;
|
|
u32 tc;
|
|
u32 ecc;
|
|
u32 dma_data;
|
|
};
|
|
|
|
/* CFG register */
|
|
#define CFG_CE_LOW (1 << 5)
|
|
#define CFG_DMA_ECC (1 << 4) /* Enable DMA ECC bit */
|
|
#define CFG_ECC_EN (1 << 3) /* ECC enable bit */
|
|
#define CFG_DMA_BURST (1 << 2) /* DMA burst bit */
|
|
#define CFG_DMA_DIR (1 << 1) /* DMA write(0)/read(1) bit */
|
|
|
|
/* CTRL register */
|
|
#define CTRL_SW_RESET (1 << 2)
|
|
#define CTRL_ECC_CLEAR (1 << 1) /* Reset ECC bit */
|
|
#define CTRL_DMA_START (1 << 0) /* Start DMA channel bit */
|
|
|
|
/* STAT register */
|
|
#define STAT_DMA_FIFO (1 << 2) /* DMA FIFO has data bit */
|
|
#define STAT_NAND_READY (1 << 0)
|
|
|
|
/* INT_STAT register */
|
|
#define INT_STAT_TC (1 << 1)
|
|
#define INT_STAT_RDY (1 << 0)
|
|
|
|
/* TAC register bits, be aware of overflows */
|
|
#define TAC_W_RDY(n) (max_t(uint32_t, (n), 0xF) << 28)
|
|
#define TAC_W_WIDTH(n) (max_t(uint32_t, (n), 0xF) << 24)
|
|
#define TAC_W_HOLD(n) (max_t(uint32_t, (n), 0xF) << 20)
|
|
#define TAC_W_SETUP(n) (max_t(uint32_t, (n), 0xF) << 16)
|
|
#define TAC_R_RDY(n) (max_t(uint32_t, (n), 0xF) << 12)
|
|
#define TAC_R_WIDTH(n) (max_t(uint32_t, (n), 0xF) << 8)
|
|
#define TAC_R_HOLD(n) (max_t(uint32_t, (n), 0xF) << 4)
|
|
#define TAC_R_SETUP(n) (max_t(uint32_t, (n), 0xF) << 0)
|
|
|
|
/* NAND ECC Layout for small page NAND devices
|
|
* Note: For large page devices, the default layouts are used. */
|
|
static struct nand_ecclayout lpc32xx_nand_oob_16 = {
|
|
.eccbytes = 6,
|
|
.eccpos = {10, 11, 12, 13, 14, 15},
|
|
.oobfree = {
|
|
{.offset = 0,
|
|
. length = 4},
|
|
{.offset = 6,
|
|
. length = 4}
|
|
}
|
|
};
|
|
|
|
#if defined(CONFIG_DMA_LPC32XX)
|
|
#define ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
|
|
|
|
/*
|
|
* DMA Descriptors
|
|
* For Large Block: 17 descriptors = ((16 Data and ECC Read) + 1 Spare Area)
|
|
* For Small Block: 5 descriptors = ((4 Data and ECC Read) + 1 Spare Area)
|
|
*/
|
|
static struct lpc32xx_dmac_ll dmalist[ECCSTEPS * 2 + 1];
|
|
static u32 ecc_buffer[8]; /* MAX ECC size */
|
|
static unsigned int dmachan = (unsigned int)-1; /* Invalid channel */
|
|
|
|
/*
|
|
* Helper macro for the DMA client (i.e. NAND SLC):
|
|
* - to write the next DMA linked list item address
|
|
* (see arch/include/asm/arch-lpc32xx/dma.h).
|
|
* - to assign the DMA data register to DMA source or destination address.
|
|
* - to assign the ECC register to DMA source or destination address.
|
|
*/
|
|
#define lpc32xx_dmac_next_lli(x) ((u32)x)
|
|
#define lpc32xx_dmac_set_dma_data() ((u32)&lpc32xx_nand_slc_regs->dma_data)
|
|
#define lpc32xx_dmac_set_ecc() ((u32)&lpc32xx_nand_slc_regs->ecc)
|
|
#endif
|
|
|
|
static struct lpc32xx_nand_slc_regs __iomem *lpc32xx_nand_slc_regs
|
|
= (struct lpc32xx_nand_slc_regs __iomem *)SLC_NAND_BASE;
|
|
|
|
static void lpc32xx_nand_init(void)
|
|
{
|
|
uint32_t hclk = get_hclk_clk_rate();
|
|
|
|
/* Reset SLC NAND controller */
|
|
writel(CTRL_SW_RESET, &lpc32xx_nand_slc_regs->ctrl);
|
|
|
|
/* 8-bit bus, no DMA, no ECC, ordinary CE signal */
|
|
writel(0, &lpc32xx_nand_slc_regs->cfg);
|
|
|
|
/* Interrupts disabled and cleared */
|
|
writel(0, &lpc32xx_nand_slc_regs->ien);
|
|
writel(INT_STAT_TC | INT_STAT_RDY,
|
|
&lpc32xx_nand_slc_regs->icr);
|
|
|
|
/* Configure NAND flash timings */
|
|
writel(TAC_W_RDY(CONFIG_LPC32XX_NAND_SLC_WDR_CLKS) |
|
|
TAC_W_WIDTH(hclk / CONFIG_LPC32XX_NAND_SLC_WWIDTH) |
|
|
TAC_W_HOLD(hclk / CONFIG_LPC32XX_NAND_SLC_WHOLD) |
|
|
TAC_W_SETUP(hclk / CONFIG_LPC32XX_NAND_SLC_WSETUP) |
|
|
TAC_R_RDY(CONFIG_LPC32XX_NAND_SLC_RDR_CLKS) |
|
|
TAC_R_WIDTH(hclk / CONFIG_LPC32XX_NAND_SLC_RWIDTH) |
|
|
TAC_R_HOLD(hclk / CONFIG_LPC32XX_NAND_SLC_RHOLD) |
|
|
TAC_R_SETUP(hclk / CONFIG_LPC32XX_NAND_SLC_RSETUP),
|
|
&lpc32xx_nand_slc_regs->tac);
|
|
}
|
|
|
|
static void lpc32xx_nand_cmd_ctrl(struct mtd_info *mtd,
|
|
int cmd, unsigned int ctrl)
|
|
{
|
|
debug("ctrl: 0x%08x, cmd: 0x%08x\n", ctrl, cmd);
|
|
|
|
if (ctrl & NAND_NCE)
|
|
setbits_le32(&lpc32xx_nand_slc_regs->cfg, CFG_CE_LOW);
|
|
else
|
|
clrbits_le32(&lpc32xx_nand_slc_regs->cfg, CFG_CE_LOW);
|
|
|
|
if (cmd == NAND_CMD_NONE)
|
|
return;
|
|
|
|
if (ctrl & NAND_CLE)
|
|
writel(cmd & 0xFF, &lpc32xx_nand_slc_regs->cmd);
|
|
else if (ctrl & NAND_ALE)
|
|
writel(cmd & 0xFF, &lpc32xx_nand_slc_regs->addr);
|
|
}
|
|
|
|
static int lpc32xx_nand_dev_ready(struct mtd_info *mtd)
|
|
{
|
|
return readl(&lpc32xx_nand_slc_regs->stat) & STAT_NAND_READY;
|
|
}
|
|
|
|
#if defined(CONFIG_DMA_LPC32XX)
|
|
/*
|
|
* Prepares DMA descriptors for NAND RD/WR operations
|
|
* If the size is < 256 Bytes then it is assumed to be
|
|
* an OOB transfer
|
|
*/
|
|
static void lpc32xx_nand_dma_configure(struct nand_chip *chip,
|
|
const u8 *buffer, int size,
|
|
int read)
|
|
{
|
|
u32 i, dmasrc, ctrl, ecc_ctrl, oob_ctrl, dmadst;
|
|
struct lpc32xx_dmac_ll *dmalist_cur;
|
|
struct lpc32xx_dmac_ll *dmalist_cur_ecc;
|
|
|
|
/*
|
|
* CTRL descriptor entry for reading ECC
|
|
* Copy Multiple times to sync DMA with Flash Controller
|
|
*/
|
|
ecc_ctrl = 0x5 |
|
|
DMAC_CHAN_SRC_BURST_1 |
|
|
DMAC_CHAN_DEST_BURST_1 |
|
|
DMAC_CHAN_SRC_WIDTH_32 |
|
|
DMAC_CHAN_DEST_WIDTH_32 |
|
|
DMAC_CHAN_DEST_AHB1;
|
|
|
|
/* CTRL descriptor entry for reading/writing Data */
|
|
ctrl = (CONFIG_SYS_NAND_ECCSIZE / 4) |
|
|
DMAC_CHAN_SRC_BURST_4 |
|
|
DMAC_CHAN_DEST_BURST_4 |
|
|
DMAC_CHAN_SRC_WIDTH_32 |
|
|
DMAC_CHAN_DEST_WIDTH_32 |
|
|
DMAC_CHAN_DEST_AHB1;
|
|
|
|
/* CTRL descriptor entry for reading/writing Spare Area */
|
|
oob_ctrl = (CONFIG_SYS_NAND_OOBSIZE / 4) |
|
|
DMAC_CHAN_SRC_BURST_4 |
|
|
DMAC_CHAN_DEST_BURST_4 |
|
|
DMAC_CHAN_SRC_WIDTH_32 |
|
|
DMAC_CHAN_DEST_WIDTH_32 |
|
|
DMAC_CHAN_DEST_AHB1;
|
|
|
|
if (read) {
|
|
dmasrc = lpc32xx_dmac_set_dma_data();
|
|
dmadst = (u32)buffer;
|
|
ctrl |= DMAC_CHAN_DEST_AUTOINC;
|
|
} else {
|
|
dmadst = lpc32xx_dmac_set_dma_data();
|
|
dmasrc = (u32)buffer;
|
|
ctrl |= DMAC_CHAN_SRC_AUTOINC;
|
|
}
|
|
|
|
/*
|
|
* Write Operation Sequence for Small Block NAND
|
|
* ----------------------------------------------------------
|
|
* 1. X'fer 256 bytes of data from Memory to Flash.
|
|
* 2. Copy generated ECC data from Register to Spare Area
|
|
* 3. X'fer next 256 bytes of data from Memory to Flash.
|
|
* 4. Copy generated ECC data from Register to Spare Area.
|
|
* 5. X'fer 16 byets of Spare area from Memory to Flash.
|
|
* Read Operation Sequence for Small Block NAND
|
|
* ----------------------------------------------------------
|
|
* 1. X'fer 256 bytes of data from Flash to Memory.
|
|
* 2. Copy generated ECC data from Register to ECC calc Buffer.
|
|
* 3. X'fer next 256 bytes of data from Flash to Memory.
|
|
* 4. Copy generated ECC data from Register to ECC calc Buffer.
|
|
* 5. X'fer 16 bytes of Spare area from Flash to Memory.
|
|
* Write Operation Sequence for Large Block NAND
|
|
* ----------------------------------------------------------
|
|
* 1. Steps(1-4) of Write Operations repeate for four times
|
|
* which generates 16 DMA descriptors to X'fer 2048 bytes of
|
|
* data & 32 bytes of ECC data.
|
|
* 2. X'fer 64 bytes of Spare area from Memory to Flash.
|
|
* Read Operation Sequence for Large Block NAND
|
|
* ----------------------------------------------------------
|
|
* 1. Steps(1-4) of Read Operations repeate for four times
|
|
* which generates 16 DMA descriptors to X'fer 2048 bytes of
|
|
* data & 32 bytes of ECC data.
|
|
* 2. X'fer 64 bytes of Spare area from Flash to Memory.
|
|
*/
|
|
|
|
for (i = 0; i < size/CONFIG_SYS_NAND_ECCSIZE; i++) {
|
|
dmalist_cur = &dmalist[i * 2];
|
|
dmalist_cur_ecc = &dmalist[(i * 2) + 1];
|
|
|
|
dmalist_cur->dma_src = (read ? (dmasrc) : (dmasrc + (i*256)));
|
|
dmalist_cur->dma_dest = (read ? (dmadst + (i*256)) : dmadst);
|
|
dmalist_cur->next_lli = lpc32xx_dmac_next_lli(dmalist_cur_ecc);
|
|
dmalist_cur->next_ctrl = ctrl;
|
|
|
|
dmalist_cur_ecc->dma_src = lpc32xx_dmac_set_ecc();
|
|
dmalist_cur_ecc->dma_dest = (u32)&ecc_buffer[i];
|
|
dmalist_cur_ecc->next_lli =
|
|
lpc32xx_dmac_next_lli(&dmalist[(i * 2) + 2]);
|
|
dmalist_cur_ecc->next_ctrl = ecc_ctrl;
|
|
}
|
|
|
|
if (i) { /* Data only transfer */
|
|
dmalist_cur_ecc = &dmalist[(i * 2) - 1];
|
|
dmalist_cur_ecc->next_lli = 0;
|
|
dmalist_cur_ecc->next_ctrl |= DMAC_CHAN_INT_TC_EN;
|
|
return;
|
|
}
|
|
|
|
/* OOB only transfer */
|
|
if (read) {
|
|
dmasrc = lpc32xx_dmac_set_dma_data();
|
|
dmadst = (u32)buffer;
|
|
oob_ctrl |= DMAC_CHAN_DEST_AUTOINC;
|
|
} else {
|
|
dmadst = lpc32xx_dmac_set_dma_data();
|
|
dmasrc = (u32)buffer;
|
|
oob_ctrl |= DMAC_CHAN_SRC_AUTOINC;
|
|
}
|
|
|
|
/* Read/ Write Spare Area Data To/From Flash */
|
|
dmalist_cur = &dmalist[i * 2];
|
|
dmalist_cur->dma_src = dmasrc;
|
|
dmalist_cur->dma_dest = dmadst;
|
|
dmalist_cur->next_lli = 0;
|
|
dmalist_cur->next_ctrl = (oob_ctrl | DMAC_CHAN_INT_TC_EN);
|
|
}
|
|
|
|
static void lpc32xx_nand_xfer(struct mtd_info *mtd, const u8 *buf,
|
|
int len, int read)
|
|
{
|
|
struct nand_chip *chip = mtd->priv;
|
|
u32 config;
|
|
int ret;
|
|
|
|
/* DMA Channel Configuration */
|
|
config = (read ? DMAC_CHAN_FLOW_D_P2M : DMAC_CHAN_FLOW_D_M2P) |
|
|
(read ? DMAC_DEST_PERIP(0) : DMAC_DEST_PERIP(DMA_PERID_NAND1)) |
|
|
(read ? DMAC_SRC_PERIP(DMA_PERID_NAND1) : DMAC_SRC_PERIP(0)) |
|
|
DMAC_CHAN_ENABLE;
|
|
|
|
/* Prepare DMA descriptors */
|
|
lpc32xx_nand_dma_configure(chip, buf, len, read);
|
|
|
|
/* Setup SLC controller and start transfer */
|
|
if (read)
|
|
setbits_le32(&lpc32xx_nand_slc_regs->cfg, CFG_DMA_DIR);
|
|
else /* NAND_ECC_WRITE */
|
|
clrbits_le32(&lpc32xx_nand_slc_regs->cfg, CFG_DMA_DIR);
|
|
setbits_le32(&lpc32xx_nand_slc_regs->cfg, CFG_DMA_BURST);
|
|
|
|
/* Write length for new transfers */
|
|
if (!((readl(&lpc32xx_nand_slc_regs->stat) & STAT_DMA_FIFO) |
|
|
readl(&lpc32xx_nand_slc_regs->tc))) {
|
|
int tmp = (len != mtd->oobsize) ? mtd->oobsize : 0;
|
|
writel(len + tmp, &lpc32xx_nand_slc_regs->tc);
|
|
}
|
|
|
|
setbits_le32(&lpc32xx_nand_slc_regs->ctrl, CTRL_DMA_START);
|
|
|
|
/* Start DMA transfers */
|
|
ret = lpc32xx_dma_start_xfer(dmachan, dmalist, config);
|
|
if (unlikely(ret < 0))
|
|
BUG();
|
|
|
|
|
|
/* Wait for NAND to be ready */
|
|
while (!lpc32xx_nand_dev_ready(mtd))
|
|
;
|
|
|
|
/* Wait till DMA transfer is DONE */
|
|
if (lpc32xx_dma_wait_status(dmachan))
|
|
pr_err("NAND DMA transfer error!\r\n");
|
|
|
|
/* Stop DMA & HW ECC */
|
|
clrbits_le32(&lpc32xx_nand_slc_regs->ctrl, CTRL_DMA_START);
|
|
clrbits_le32(&lpc32xx_nand_slc_regs->cfg,
|
|
CFG_DMA_DIR | CFG_DMA_BURST | CFG_ECC_EN | CFG_DMA_ECC);
|
|
}
|
|
|
|
static u32 slc_ecc_copy_to_buffer(u8 *spare, const u32 *ecc, int count)
|
|
{
|
|
int i;
|
|
for (i = 0; i < (count * CONFIG_SYS_NAND_ECCBYTES);
|
|
i += CONFIG_SYS_NAND_ECCBYTES) {
|
|
u32 ce = ecc[i / CONFIG_SYS_NAND_ECCBYTES];
|
|
ce = ~(ce << 2) & 0xFFFFFF;
|
|
spare[i+2] = (u8)(ce & 0xFF); ce >>= 8;
|
|
spare[i+1] = (u8)(ce & 0xFF); ce >>= 8;
|
|
spare[i] = (u8)(ce & 0xFF);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int lpc32xx_ecc_calculate(struct mtd_info *mtd, const uint8_t *dat,
|
|
uint8_t *ecc_code)
|
|
{
|
|
return slc_ecc_copy_to_buffer(ecc_code, ecc_buffer, ECCSTEPS);
|
|
}
|
|
|
|
/*
|
|
* Enables and prepares SLC NAND controller
|
|
* for doing data transfers with H/W ECC enabled.
|
|
*/
|
|
static void lpc32xx_hwecc_enable(struct mtd_info *mtd, int mode)
|
|
{
|
|
/* Clear ECC */
|
|
writel(CTRL_ECC_CLEAR, &lpc32xx_nand_slc_regs->ctrl);
|
|
|
|
/* Setup SLC controller for H/W ECC operations */
|
|
setbits_le32(&lpc32xx_nand_slc_regs->cfg, CFG_ECC_EN | CFG_DMA_ECC);
|
|
}
|
|
|
|
/*
|
|
* lpc32xx_correct_data - [NAND Interface] Detect and correct bit error(s)
|
|
* mtd: MTD block structure
|
|
* dat: raw data read from the chip
|
|
* read_ecc: ECC from the chip
|
|
* calc_ecc: the ECC calculated from raw data
|
|
*
|
|
* Detect and correct a 1 bit error for 256 byte block
|
|
*/
|
|
int lpc32xx_correct_data(struct mtd_info *mtd, u_char *dat,
|
|
u_char *read_ecc, u_char *calc_ecc)
|
|
{
|
|
unsigned int i;
|
|
int ret1, ret2 = 0;
|
|
u_char *r = read_ecc;
|
|
u_char *c = calc_ecc;
|
|
u16 data_offset = 0;
|
|
|
|
for (i = 0 ; i < ECCSTEPS ; i++) {
|
|
r += CONFIG_SYS_NAND_ECCBYTES;
|
|
c += CONFIG_SYS_NAND_ECCBYTES;
|
|
data_offset += CONFIG_SYS_NAND_ECCSIZE;
|
|
|
|
ret1 = nand_correct_data(mtd, dat + data_offset, r, c);
|
|
if (ret1 < 0)
|
|
return -EBADMSG;
|
|
else
|
|
ret2 += ret1;
|
|
}
|
|
|
|
return ret2;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_DMA_LPC32XX)
|
|
static void lpc32xx_dma_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
|
|
{
|
|
lpc32xx_nand_xfer(mtd, buf, len, 1);
|
|
}
|
|
#else
|
|
static void lpc32xx_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
|
|
{
|
|
while (len-- > 0)
|
|
*buf++ = readl(&lpc32xx_nand_slc_regs->data);
|
|
}
|
|
#endif
|
|
|
|
static uint8_t lpc32xx_read_byte(struct mtd_info *mtd)
|
|
{
|
|
return readl(&lpc32xx_nand_slc_regs->data);
|
|
}
|
|
|
|
#if defined(CONFIG_DMA_LPC32XX)
|
|
static void lpc32xx_dma_write_buf(struct mtd_info *mtd, const uint8_t *buf,
|
|
int len)
|
|
{
|
|
lpc32xx_nand_xfer(mtd, buf, len, 0);
|
|
}
|
|
#else
|
|
static void lpc32xx_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
|
|
{
|
|
while (len-- > 0)
|
|
writel(*buf++, &lpc32xx_nand_slc_regs->data);
|
|
}
|
|
#endif
|
|
|
|
static void lpc32xx_write_byte(struct mtd_info *mtd, uint8_t byte)
|
|
{
|
|
writel(byte, &lpc32xx_nand_slc_regs->data);
|
|
}
|
|
|
|
#if defined(CONFIG_DMA_LPC32XX)
|
|
/* Reuse the logic from "nand_read_page_hwecc()" */
|
|
static int lpc32xx_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
|
|
uint8_t *buf, int oob_required, int page)
|
|
{
|
|
int i;
|
|
int stat;
|
|
uint8_t *p = buf;
|
|
uint8_t *ecc_calc = chip->buffers->ecccalc;
|
|
uint8_t *ecc_code = chip->buffers->ecccode;
|
|
uint32_t *eccpos = chip->ecc.layout->eccpos;
|
|
unsigned int max_bitflips = 0;
|
|
|
|
/*
|
|
* As per the "LPC32x0 and LPC32x0/01 User manual" table 173 notes
|
|
* and section 9.7, the NAND SLC & DMA allowed single DMA transaction
|
|
* of a page size using DMA controller scatter/gather mode through
|
|
* linked list; the ECC read is done without any software intervention.
|
|
*/
|
|
|
|
lpc32xx_hwecc_enable(mtd, NAND_ECC_READ);
|
|
lpc32xx_dma_read_buf(mtd, p, chip->ecc.size * chip->ecc.steps);
|
|
lpc32xx_ecc_calculate(mtd, p, &ecc_calc[0]);
|
|
lpc32xx_dma_read_buf(mtd, chip->oob_poi, mtd->oobsize);
|
|
|
|
for (i = 0; i < chip->ecc.total; i++)
|
|
ecc_code[i] = chip->oob_poi[eccpos[i]];
|
|
|
|
stat = chip->ecc.correct(mtd, p, &ecc_code[0], &ecc_calc[0]);
|
|
if (stat < 0)
|
|
mtd->ecc_stats.failed++;
|
|
else {
|
|
mtd->ecc_stats.corrected += stat;
|
|
max_bitflips = max_t(unsigned int, max_bitflips, stat);
|
|
}
|
|
|
|
return max_bitflips;
|
|
}
|
|
|
|
/* Reuse the logic from "nand_write_page_hwecc()" */
|
|
static int lpc32xx_write_page_hwecc(struct mtd_info *mtd,
|
|
struct nand_chip *chip,
|
|
const uint8_t *buf, int oob_required)
|
|
{
|
|
int i;
|
|
uint8_t *ecc_calc = chip->buffers->ecccalc;
|
|
const uint8_t *p = buf;
|
|
uint32_t *eccpos = chip->ecc.layout->eccpos;
|
|
|
|
/*
|
|
* As per the "LPC32x0 and LPC32x0/01 User manual" table 173 notes
|
|
* and section 9.7, the NAND SLC & DMA allowed single DMA transaction
|
|
* of a page size using DMA controller scatter/gather mode through
|
|
* linked list; the ECC read is done without any software intervention.
|
|
*/
|
|
|
|
lpc32xx_hwecc_enable(mtd, NAND_ECC_WRITE);
|
|
lpc32xx_dma_write_buf(mtd, p, chip->ecc.size * chip->ecc.steps);
|
|
lpc32xx_ecc_calculate(mtd, p, &ecc_calc[0]);
|
|
|
|
for (i = 0; i < chip->ecc.total; i++)
|
|
chip->oob_poi[eccpos[i]] = ecc_calc[i];
|
|
|
|
lpc32xx_dma_write_buf(mtd, chip->oob_poi, mtd->oobsize);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* LPC32xx has only one SLC NAND controller, don't utilize
|
|
* CONFIG_SYS_NAND_SELF_INIT to be able to reuse this function
|
|
* both in SPL NAND and U-boot images.
|
|
*/
|
|
int board_nand_init(struct nand_chip *lpc32xx_chip)
|
|
{
|
|
#if defined(CONFIG_DMA_LPC32XX)
|
|
int ret;
|
|
|
|
/* Acquire a channel for our use */
|
|
ret = lpc32xx_dma_get_channel();
|
|
if (unlikely(ret < 0)) {
|
|
pr_info("Unable to get free DMA channel for NAND transfers\n");
|
|
return -1;
|
|
}
|
|
dmachan = (unsigned int)ret;
|
|
#endif
|
|
|
|
lpc32xx_chip->cmd_ctrl = lpc32xx_nand_cmd_ctrl;
|
|
lpc32xx_chip->dev_ready = lpc32xx_nand_dev_ready;
|
|
|
|
/*
|
|
* The implementation of these functions is quite common, but
|
|
* they MUST be defined, because access to data register
|
|
* is strictly 32-bit aligned.
|
|
*/
|
|
lpc32xx_chip->read_byte = lpc32xx_read_byte;
|
|
lpc32xx_chip->write_byte = lpc32xx_write_byte;
|
|
|
|
#if defined(CONFIG_DMA_LPC32XX)
|
|
/* Hardware ECC calculation is supported when DMA driver is selected */
|
|
lpc32xx_chip->ecc.mode = NAND_ECC_HW;
|
|
|
|
lpc32xx_chip->read_buf = lpc32xx_dma_read_buf;
|
|
lpc32xx_chip->write_buf = lpc32xx_dma_write_buf;
|
|
|
|
lpc32xx_chip->ecc.calculate = lpc32xx_ecc_calculate;
|
|
lpc32xx_chip->ecc.correct = lpc32xx_correct_data;
|
|
lpc32xx_chip->ecc.hwctl = lpc32xx_hwecc_enable;
|
|
lpc32xx_chip->chip_delay = 2000;
|
|
|
|
lpc32xx_chip->ecc.read_page = lpc32xx_read_page_hwecc;
|
|
lpc32xx_chip->ecc.write_page = lpc32xx_write_page_hwecc;
|
|
lpc32xx_chip->options |= NAND_NO_SUBPAGE_WRITE;
|
|
#else
|
|
/*
|
|
* Hardware ECC calculation is not supported by the driver,
|
|
* because it requires DMA support, see LPC32x0 User Manual,
|
|
* note after SLC_ECC register description (UM10326, p.198)
|
|
*/
|
|
lpc32xx_chip->ecc.mode = NAND_ECC_SOFT;
|
|
|
|
/*
|
|
* The implementation of these functions is quite common, but
|
|
* they MUST be defined, because access to data register
|
|
* is strictly 32-bit aligned.
|
|
*/
|
|
lpc32xx_chip->read_buf = lpc32xx_read_buf;
|
|
lpc32xx_chip->write_buf = lpc32xx_write_buf;
|
|
#endif
|
|
|
|
/*
|
|
* These values are predefined
|
|
* for both small and large page NAND flash devices.
|
|
*/
|
|
lpc32xx_chip->ecc.size = CONFIG_SYS_NAND_ECCSIZE;
|
|
lpc32xx_chip->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES;
|
|
lpc32xx_chip->ecc.strength = 1;
|
|
|
|
if (CONFIG_SYS_NAND_PAGE_SIZE != NAND_LARGE_BLOCK_PAGE_SIZE)
|
|
lpc32xx_chip->ecc.layout = &lpc32xx_nand_oob_16;
|
|
|
|
#if defined(CONFIG_SYS_NAND_USE_FLASH_BBT)
|
|
lpc32xx_chip->bbt_options |= NAND_BBT_USE_FLASH;
|
|
#endif
|
|
|
|
/* Initialize NAND interface */
|
|
lpc32xx_nand_init();
|
|
|
|
return 0;
|
|
}
|