mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-14 22:23:56 +09:00
![Tim Harvey](/assets/img/avatar_default.png)
Prepare for boards with EMMC instead of NAND flash Signed-off-by: Tim Harvey <tharvey@gateworks.com>
321 lines
13 KiB
Plaintext
321 lines
13 KiB
Plaintext
U-Boot for the Gateworks Ventana Product Family boards
|
|
|
|
This file contains information for the port of U-Boot to the Gateworks
|
|
Ventana Product family boards.
|
|
|
|
The entire Ventana product family (http://www.gateworks.com/product#ventana)
|
|
is supported by a single bootloader build by using a common SPL and U-Boot
|
|
that dynamically determines the characterstics of the board at runtime via
|
|
information from an EEPROM on the board programmed at the factory and supports
|
|
all of the various boot mediums available.
|
|
|
|
1. Secondary Program Loader (SPL)
|
|
---------------------------------
|
|
|
|
The i.MX6 has a BOOT ROM PPL (Primary Program Loader) which supports loading
|
|
an executable image from various boot devices.
|
|
|
|
The Gateworks Ventana board config uses an SPL build configuration. This
|
|
will build the following artifacts from U-Boot source:
|
|
- SPL - Secondary Program Loader that the i.MX6 BOOT ROM (Primary Program
|
|
Loader) boots. This detects CPU/DRAM configuration, configures
|
|
The DRAM controller, loads u-boot.img from the detected boot device,
|
|
and jumps to it. As this is booted from the PPL, it has an IVT/DCD
|
|
table.
|
|
- u-boot.img - The main U-Boot core which is u-boot.bin with a image header.
|
|
|
|
|
|
2. Build
|
|
--------
|
|
|
|
To build U-Boot for the Gateworks Ventana product family:
|
|
|
|
For NAND FLASH based boards:
|
|
make gwventana_nand_config
|
|
make
|
|
|
|
For EMMC FLASH based boards:
|
|
make gwventana_emmc_config
|
|
make
|
|
|
|
|
|
3. Boot source:
|
|
---------------
|
|
|
|
The Gateworks Ventana boards support booting from NAND or micro-SD depending
|
|
on the board model. The IMX6 BOOT ROM will choose a boot media based on eFUSE
|
|
settings programmed at the factory.
|
|
|
|
Boards with NAND flash will always boot from NAND, and NAND-less boards will
|
|
always boot from micro-SD. However, it is possible to use the U-Boot bmode
|
|
command (or the technique it uses) to essentially bootstrap to another boot
|
|
media at runtime.
|
|
|
|
3.1. boot from NAND
|
|
-------------------
|
|
|
|
The i.MX6 BOOT ROM expects some structures that provide details of NAND layout
|
|
and bad block information (referred to as 'bootstreams') which are replicated
|
|
multiple times in NAND. The number of replications and their spacing (referred
|
|
to as search stride) is configurable through board strapping options and/or
|
|
eFUSE settings (BOOT_SEARCH_COUNT / Pages in block from BOOT_CFG2). In
|
|
addition, the i.MX6 BOOT ROM Flash Configuration Block (FCB) supports two
|
|
copies of a bootloader in flash in the case that a bad block has corrupted one.
|
|
The Freescale 'kobs-ng' application from the Freescale LTIB BSP, which runs
|
|
under Linux and operates on an MTD partition, must be used to program the
|
|
bootstream in order to setup this flash structure correctly.
|
|
|
|
The Gateworks Ventana boards with NAND flash have been factory programmed
|
|
such that their eFUSE settings expect 2 copies of the boostream (this is
|
|
specified by providing kobs-ng with the --search_exponent=1 argument). Once in
|
|
Linux with MTD support for the NAND on /dev/mtd0 you can program the SPL
|
|
with:
|
|
|
|
kobs-ng init -v -x --search_exponent=1 SPL
|
|
|
|
The kobs-ng application uses an imximage which contains the Image Vector Table
|
|
(IVT) and Device Configuration Data (DCD) structures that the i.MX6 BOOT ROM
|
|
requires to boot. The kobs-ng adds the Firmware Configuration Block (FCB) and
|
|
Discovered Bad Block Table (DBBT). The SPL build artifact from U-Boot is
|
|
an imximage.
|
|
|
|
The u-boot.img, which is the non SPL U-Boot binary appended to a U-Boot image
|
|
header must be programmed in the NAND flash boot device at an offset hard
|
|
coded in the SPL. For the Ventana boards, this has been chosen to be 14MB.
|
|
The image can be programmed from either U-Boot or Linux:
|
|
|
|
U-Boot:
|
|
Ventana > setenv mtdparts mtdparts=nand:14m(spl),2m(uboot),1m(env),-(rootfs)
|
|
Ventana > tftp ${loadaddr} u-boot.img && nand erase.part uboot && \
|
|
nand write ${loadaddr} uboot ${filesize}
|
|
|
|
Linux:
|
|
nandwrite /dev/mtd1 u-boot.img
|
|
|
|
The above assumes the default Ventana partitioning scheme which is configured
|
|
via the mtdparts env var:
|
|
- spl: 14MB
|
|
- uboot: 2M
|
|
- env: 1M
|
|
- rootfs: the rest
|
|
|
|
This information is taken from:
|
|
http://trac.gateworks.com/wiki/ventana/bootloader#nand
|
|
|
|
More details about the i.MX6 BOOT ROM can be found in the IMX6 reference manual.
|
|
|
|
3.1. boot from MMC (eMMC/microSD)
|
|
---------------------------------
|
|
|
|
When the IMX6 eFUSE settings have been factory programmed to boot from
|
|
MMC the SPL will be loaded from offset 0x400 (1KB). Once the SPL is
|
|
booted, it will load and execute U-Boot (u-boot.img) from offset 69KB
|
|
on the micro-SD (defined by CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR).
|
|
|
|
While it is technically possible to enable the SPL to be able to load
|
|
U-Boot from a file on a FAT/EXT filesystem on the micro-SD, we chose to
|
|
use raw micro-SD access to keep the code-size and boot time of the SPL down.
|
|
|
|
For these reasons an MMC device that will be used as an IMX6 primary boot
|
|
device must be carefully partitioned and prepared.
|
|
|
|
The following shell commands are executed on a Linux host (adjust DEV to the
|
|
block storage device of your MMC, ie /dev/mmcblk0):
|
|
|
|
DEV=/dev/sdc
|
|
# zero out 1MB of device
|
|
sudo dd if=/dev/zero of=$DEV count=1 bs=1M oflag=sync status=none && sync
|
|
# copy SPL to 1KB offset
|
|
sudo dd if=SPL of=$DEV bs=1K seek=1 oflag=sync status=none && sync
|
|
# copy U-Boot to 69KB offset
|
|
sudo dd if=u-boot.img of=$DEV bs=1K seek=69 oflag=sync status=none && sync
|
|
# create a partition table with a single rootfs partition starting at 1MB
|
|
printf "1,,L\n" | sudo sfdisk --in-order --no-reread -L -uM $DEV && sync
|
|
# format partition
|
|
sudo mkfs.ext4 -L root ${DEV}1
|
|
# mount the partition
|
|
sudo udisks --mount ${DEV}1
|
|
# extract filesystem
|
|
sudo tar xvf rootfs.tar.gz -C /media/root
|
|
# flush and unmount
|
|
sync && sudo umount /media/root
|
|
|
|
The above assumes the default Ventana micro-SD partitioning scheme
|
|
- spl : 1KB-69KB (68KB) required by IMX6 BOOT ROM
|
|
- uboot : 69KB-709KB (640KB) defined by
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
|
|
- env : 709KB-965KB (256KB) defined by
|
|
CONFIG_ENV_MMC_SIZE
|
|
CONFIG_ENV_MMC_OFFSET_REDUND
|
|
- rootfs : 1MB-
|
|
|
|
This information is taken from:
|
|
http://trac.gateworks.com/wiki/ventana/bootloader#microsd
|
|
|
|
More details about the i.MX6 BOOT ROM can be found in the IMX6 reference manual.
|
|
|
|
4. Falcon Mode
|
|
------------------------------
|
|
|
|
The Gateworks Ventana board config enables Falcon mode (CONFIG_SPL_OS_BOOT)
|
|
which allows the SPL to boot directly to an OS instead of to U-Boot
|
|
(u-boot.img) thus acheiving a faster overall boot time. The time savings
|
|
depends on your boot medium (ie NAND Flash vs micro-SD) and size/storage
|
|
of the OS. The time savings can be anywhere from 2 seconds (256MB NAND Flash
|
|
with ~1MB kernel) to 6 seconds or more (2GB NAND Flash with ~6 kernel)
|
|
|
|
The Gateworks Ventana board supports Falcon mode for the following boot
|
|
medium:
|
|
- NAND flash
|
|
- micro-SD
|
|
|
|
For all boot mediums, raw mode is used. While support of more complex storage
|
|
such as files on top of FAT/EXT filesystem is possible but not practical
|
|
as the size of the SPL is fairly limitted (to 64KB based on the smallest
|
|
size of available IMX6 iRAM) as well as the fact that this would increase
|
|
OS load time which defeats the purpose of Falcon mode in the first place.
|
|
|
|
The SPL decides to boot either U-Boot (u-boot.img) or the OS (args + kernel)
|
|
based on the return value of the spl_start_uboot() function. While often
|
|
this can simply be the state of a GPIO based pushbutton or DIP switch, for
|
|
Gateworks Ventana, we use an EEPROM register on i2c-0 at 0x50:0x00:
|
|
set to '0' will choose to boot to U-Boot and otherwise it will boot to OS.
|
|
|
|
To use Falcon mode it is required that you first 'prepare' the 'args' data
|
|
that is stored on your boot medium along with the kernel (which can be any
|
|
OS or bare-metal application). In the case of the Linux kernel the 'args'
|
|
is the flatenned device-tree which normally gets altered prior to booting linux
|
|
by U-Boot's 'bootm' command. To achieve this for SPL we use the
|
|
'spl export fdt' command in U-Boot after loading the kernel and dtb which
|
|
will go through the same process of modifying the device-tree for the board
|
|
being executed on but not jump to the kernel. This allows you to save the
|
|
args data to the location the SPL expects it and then enable Falcon mode.
|
|
|
|
It is important to realize that there are certain values in the dtb that
|
|
are board model specific (IMX6Q vs IMX6DL for example) and board specific
|
|
(board serial number, MAC addrs) so you do not want to use the 'args'
|
|
data prepared from one board on another board.
|
|
|
|
4.1. Falcon Mode on NAND flash
|
|
------------------------------
|
|
To prepare a Gateworks Ventana board that boots from NAND flash for Falcon
|
|
mode you must program your flash such that the 'args' and 'kernel' are
|
|
located where defined at compile time by the following:
|
|
CONFIG_CMD_SPL_NAND_OFS 17MB - offset of 'args'
|
|
CONFIG_SYS_NAND_SPL_KERNEL_OFFS 18MB - offset of 'kernel'
|
|
|
|
The location offsets defined above are defaults chosen by Gateworks and are
|
|
flexible if you want to re-define them.
|
|
|
|
The following steps executed in U-Boot will configure Falcon mode for NAND
|
|
using rootfs (ubi), kernel (uImage), and dtb from the network:
|
|
|
|
# change mtd partitions to the above mapping
|
|
Ventana > setenv mtdparts 'mtdparts=nand:14m(spl),2m(uboot),1m(env),1m(args),10m(kernel),-(rootfs)'
|
|
|
|
# flash rootfs (at 28MB)
|
|
Ventana > tftp ${loadaddr} rootfs_${flash_layout}.ubi && \
|
|
nand erase.part rootfs && nand write ${loadaddr} rootfs ${filesize}
|
|
|
|
# load the device-tree
|
|
Ventana > tftp ${fdt_addr} ventana/${fdt_file2}
|
|
|
|
# load the kernel
|
|
Ventana > tftp ${loadaddr} ventana/uImage
|
|
|
|
# flash kernel (at 18MB)
|
|
Ventana > nand erase.part kernel && nand write ${loadaddr} kernel ${filesize}
|
|
|
|
# set kernel args for the console and rootfs (used by spl export)
|
|
Ventana > setenv bootargs 'console=ttymxc1,115200 root=ubi0:rootfs ubi.mtd=5 rootfstype=ubifs quiet'
|
|
|
|
# create args based on env, board, EEPROM, and dtb
|
|
Ventana > spl export fdt ${loadaddr} - ${fdt_addr}
|
|
|
|
# flash args (at 17MB)
|
|
Ventana > nand erase.part args && nand write 18000000 args 100000
|
|
|
|
# set i2c register 0x50:0x00=0 to boot to Linux
|
|
Ventana > i2c dev 0 && i2c mw 0x50 0x00.0 0 1
|
|
|
|
Be sure to adjust 'bootargs' above to your OS needs (this will be different
|
|
for various distros such as OpenWrt, Yocto, Android, etc). You can use the
|
|
value obtained from 'cat /proc/cmdline' when booted to Linux.
|
|
|
|
This information is taken from:
|
|
http://trac.gateworks.com/wiki/ventana/bootloader/falcon-mode#nand
|
|
|
|
|
|
4.2. Falcon Mode on micro-SD card
|
|
---------------------------------
|
|
|
|
To prepare a Gateworks Ventana board with a primary boot device of micro-SD
|
|
you first need to make sure you build U-Boot with CONFIG_ENV_IS_IN_MMC
|
|
instead of CONFIG_ENV_IS_IN_NAND.
|
|
|
|
For micro-SD based Falcon mode you must program your micro-SD such that
|
|
the 'args' and 'kernel' are located where defined at compile time
|
|
by the following:
|
|
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 (1MB) - offset of 'args'
|
|
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 (2MB) - offset of 'kernel'
|
|
|
|
The location offsets defined above are defaults chosen by Gateworks and are
|
|
flexible if you want to re-define them.
|
|
|
|
First you must prepare a micro-SD such that the SPL can be loaded by the
|
|
IMX6 BOOT ROM (fixed offset of 1KB), and U-Boot can be loaded by the SPL
|
|
(fixed offset of 69KB defined by CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR).
|
|
|
|
The following shell commands are executed on a Linux host (adjust DEV to the
|
|
block storage device of your micro-SD):
|
|
|
|
DEV=/dev/sdc
|
|
# zero out 1MB of device
|
|
sudo dd if=/dev/zero of=$DEV count=1 bs=1M oflag=sync status=none && sync
|
|
# copy SPL to 1KB offset
|
|
sudo dd if=SPL of=$DEV bs=1K seek=1 oflag=sync status=none && sync
|
|
# copy U-Boot to 69KB offset
|
|
sudo dd if=u-boot.img of=$DEV bs=1K seek=69 oflag=sync status=none && sync
|
|
# create a partition table with a single rootfs partition starting at 10MB
|
|
printf "10,,L\n" | sudo sfdisk --in-order --no-reread -L -uM $DEV && sync
|
|
# format partition
|
|
sudo mkfs.ext4 -L root ${DEV}1
|
|
# mount the partition
|
|
sudo udisks --mount ${DEV}1
|
|
# extract filesystem
|
|
sudo tar xvf rootfs.tar.gz -C /media/root
|
|
# flush and unmount
|
|
sync && sudo umount /media/root
|
|
|
|
Now that your micro-SD partitioning has been adjusted to leave room for the
|
|
raw 'args' and 'kernel' data boot the board with the prepared micro-SD, break
|
|
out in U-Boot and use the following to enable Falcon mode:
|
|
|
|
# load device-tree from rootfs
|
|
Ventana > ext2load mmc 0:1 ${fdt_addr} boot/${fdt_file2}
|
|
|
|
# load kernel from rootfs
|
|
Ventana > ext2load mmc 0:1 ${loadaddr} boot/uImage
|
|
|
|
# write kernel at 2MB offset
|
|
Ventana > mmc write ${loadaddr} 0x1000 0x4000
|
|
|
|
# setup kernel bootargs
|
|
Ventana > setenv bootargs 'console=ttymxc1,115200 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait rw'
|
|
|
|
# prepare args
|
|
Ventana > spl export fdt ${loadaddr} - ${fdt_addr}
|
|
|
|
# write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)
|
|
Ventana > mmc write 18000000 0x800 0x800
|
|
|
|
# set i2c register 0x50:0x00=0 to boot to Linux
|
|
Ventana > i2c dev 0 && i2c mw 0x50 0x00.0 0 1
|
|
|
|
Be sure to adjust 'bootargs' above to your OS needs (this will be different
|
|
for various distros such as OpenWrt, Yocto, Android, etc). You can use the
|
|
value obtained from 'cat /proc/cmdline' when booted to Linux.
|
|
|
|
This information is taken from:
|
|
http://trac.gateworks.com/wiki/ventana/bootloader/falcon-mode#microsd
|