u-boot-brain/include/configs/imx8qxp_mek.h
Fabio Estevam 10a8cc01b3 imx8qxp_mek: Fix the console command line string
Currently the expansion of the console variable leads to
the following kernel command line:

console=ttyLP0,${baudrate} earlycon root=/dev/mmcblk1p2 rootwait rw

, which causes the console to not show characters after the LPUART driver
is probed as the 'baudrate' variable is not properly translated.

Fix it by splitting the console variable in two parts: one for the
ttyLP0 part and the other one for the baudrate, which matches the way
it is done on other i.MX targets.

Tested by successfully booting a mainline kernel on a i.MX8QXP MEK
board.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-03-09 15:03:31 +01:00

205 lines
5.6 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2018 NXP
*/
#ifndef __IMX8QXP_MEK_H
#define __IMX8QXP_MEK_H
#include <linux/sizes.h>
#include <asm/arch/imx-regs.h>
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_MAX_SIZE (124 * 1024)
#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x800
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK 0x013E000
#define CONFIG_SPL_BSS_START_ADDR 0x00128000
#define CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */
#define CONFIG_SYS_SPL_MALLOC_START 0x00120000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */
#define CONFIG_SERIAL_LPUART_BASE 0x5a060000
#define CONFIG_MALLOC_F_ADDR 0x00120000
#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#define CONFIG_OF_EMBED
#endif
#define CONFIG_REMAKE_ELF
#define CONFIG_BOARD_EARLY_INIT_F
/* Flat Device Tree Definitions */
#define CONFIG_OF_BOARD_SETUP
#undef CONFIG_CMD_EXPORTENV
#undef CONFIG_CMD_IMPORTENV
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_CRC32
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define USDHC1_BASE_ADDR 0x5B010000
#define USDHC2_BASE_ADDR 0x5B020000
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#ifdef CONFIG_AHAB_BOOT
#define AHAB_ENV "sec_boot=yes\0"
#else
#define AHAB_ENV "sec_boot=no\0"
#endif
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
AHAB_ENV \
"script=boot.scr\0" \
"image=Image\0" \
"panel=NULL\0" \
"console=ttyLP0\0" \
"fdt_addr=0x83000000\0" \
"fdt_high=0xffffffffffffffff\0" \
"boot_fdt=try\0" \
"fdt_file=imx8qxp-mek.dtb\0" \
"initrd_addr=0x83800000\0" \
"initrd_high=0xffffffffffffffff\0" \
"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot}\0 " \
"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"loadcntr=fatload mmc ${mmcdev}:${mmcpart} ${cntr_addr} ${cntr_file}\0" \
"auth_os=auth_cntr ${cntr_addr}\0" \
"boot_os=booti ${loadaddr} - ${fdt_addr};\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${sec_boot} = yes; then " \
"if run auth_os; then " \
"run boot_os; " \
"else " \
"echo ERR: failed to authenticate; " \
"fi; " \
"else " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"run boot_os; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"else " \
"echo wait for boot; " \
"fi;" \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"if test ${sec_boot} = yes; then " \
"${get_cmd} ${cntr_addr} ${cntr_file}; " \
"if run auth_os; then " \
"run boot_os; " \
"else " \
"echo ERR: failed to authenticate; " \
"fi; " \
"else " \
"${get_cmd} ${loadaddr} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"run boot_os; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"else " \
"booti; " \
"fi;" \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if test ${sec_boot} = yes; then " \
"if run loadcntr; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
"else " \
"if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
"fi; " \
"fi; " \
"else booti ${loadaddr} - ${fdt_addr}; fi"
/* Link Definitions */
#define CONFIG_LOADADDR 0x80280000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_INIT_SP_ADDR 0x80200000
/* Default environment is in SD */
#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
/* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board */
#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */
#define CONFIG_SYS_FSL_USDHC_NUM 2
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024)) * 1024)
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define PHYS_SDRAM_1 0x80000000
#define PHYS_SDRAM_2 0x880000000
#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */
/* LPDDR4 board total DDR is 3GB */
#define PHYS_SDRAM_2_SIZE 0x40000000 /* 1 GB */
/* Serial */
#define CONFIG_BAUDRATE 115200
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 8000000 /* 8MHz */
#ifndef CONFIG_DM_PCA953X
#define CONFIG_PCA953X
#define CONFIG_CMD_PCA953X
#define CONFIG_CMD_PCA953X_INFO
#endif
/* Networking */
#define CONFIG_FEC_XCV_TYPE RGMII
#define FEC_QUIRK_ENET_MAC
/* Misc configuration */
#define CONFIG_SYS_CBSIZE 2048
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#endif /* __IMX8QXP_MEK_H */