mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-21 01:18:52 +09:00
![Grygorii Strashko](/assets/img/avatar_default.png)
As part of preparation for nand DM conversion the new API has been introduced to remove direct access to nand_info array. So, use it here instead of accessing to nand_info array directly Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
343 lines
9.1 KiB
C
343 lines
9.1 KiB
C
/*
|
|
* Cortina CS4315/CS4340 10G PHY drivers
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
|
*
|
|
*/
|
|
|
|
#include <config.h>
|
|
#include <common.h>
|
|
#include <malloc.h>
|
|
#include <linux/ctype.h>
|
|
#include <linux/string.h>
|
|
#include <linux/err.h>
|
|
#include <phy.h>
|
|
#include <cortina.h>
|
|
#ifdef CONFIG_SYS_CORTINA_FW_IN_NAND
|
|
#include <nand.h>
|
|
#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
|
|
#include <spi_flash.h>
|
|
#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
|
|
#include <mmc.h>
|
|
#endif
|
|
|
|
#ifndef CONFIG_PHYLIB_10G
|
|
#error The Cortina PHY needs 10G support
|
|
#endif
|
|
|
|
struct cortina_reg_config cortina_reg_cfg[] = {
|
|
/* CS4315_enable_sr_mode */
|
|
{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
|
|
{VILLA_MSEQ_OPTIONS, 0xf},
|
|
{VILLA_MSEQ_PC, 0x0},
|
|
{VILLA_MSEQ_BANKSELECT, 0x4},
|
|
{VILLA_LINE_SDS_COMMON_SRX0_RX_CPA, 0x55},
|
|
{VILLA_LINE_SDS_COMMON_SRX0_RX_LOOP_FILTER, 0x30},
|
|
{VILLA_DSP_SDS_SERDES_SRX_DFE0_SELECT, 0x1},
|
|
{VILLA_DSP_SDS_DSP_COEF_DFE0_SELECT, 0x2},
|
|
{VILLA_LINE_SDS_COMMON_SRX0_RX_CPB, 0x2003},
|
|
{VILLA_DSP_SDS_SERDES_SRX_FFE_DELAY_CTRL, 0xF047},
|
|
{VILLA_MSEQ_ENABLE_MSB, 0x0000},
|
|
{VILLA_MSEQ_SPARE21_LSB, 0x6},
|
|
{VILLA_MSEQ_RESET_COUNT_LSB, 0x0},
|
|
{VILLA_MSEQ_SPARE12_MSB, 0x0000},
|
|
/*
|
|
* to invert the receiver path, uncomment the next line
|
|
* write (VILLA_MSEQ_SPARE12_MSB, 0x4000)
|
|
*
|
|
* SPARE2_LSB is used to configure the device while in sr mode to
|
|
* enable power savings and to use the optical module LOS signal.
|
|
* in power savings mode, the internal prbs checker can not be used.
|
|
* if the optical module LOS signal is used as an input to the micro
|
|
* code, then the micro code will wait until the optical module
|
|
* LOS = 0 before turning on the adaptive equalizer.
|
|
* Setting SPARE2_LSB bit 0 to 1 places the devie in power savings mode
|
|
* while setting bit 0 to 0 disables power savings mode.
|
|
* Setting SPARE2_LSB bit 2 to 0 configures the device to use the
|
|
* optical module LOS signal while setting bit 2 to 1 configures the
|
|
* device so that it will ignore the optical module LOS SPARE2_LSB = 0
|
|
*/
|
|
|
|
/* enable power savings, ignore optical module LOS */
|
|
{VILLA_MSEQ_SPARE2_LSB, 0x5},
|
|
|
|
{VILLA_MSEQ_SPARE7_LSB, 0x1e},
|
|
{VILLA_MSEQ_BANKSELECT, 0x4},
|
|
{VILLA_MSEQ_SPARE9_LSB, 0x2},
|
|
{VILLA_MSEQ_SPARE3_LSB, 0x0F53},
|
|
{VILLA_MSEQ_SPARE3_MSB, 0x2006},
|
|
{VILLA_MSEQ_SPARE8_LSB, 0x3FF7},
|
|
{VILLA_MSEQ_SPARE8_MSB, 0x0A46},
|
|
{VILLA_MSEQ_COEF8_FFE0_LSB, 0xD500},
|
|
{VILLA_MSEQ_COEF8_FFE1_LSB, 0x0200},
|
|
{VILLA_MSEQ_COEF8_FFE2_LSB, 0xBA00},
|
|
{VILLA_MSEQ_COEF8_FFE3_LSB, 0x0100},
|
|
{VILLA_MSEQ_COEF8_FFE4_LSB, 0x0300},
|
|
{VILLA_MSEQ_COEF8_FFE5_LSB, 0x0300},
|
|
{VILLA_MSEQ_COEF8_DFE0_LSB, 0x0700},
|
|
{VILLA_MSEQ_COEF8_DFE0N_LSB, 0x0E00},
|
|
{VILLA_MSEQ_COEF8_DFE1_LSB, 0x0B00},
|
|
{VILLA_DSP_SDS_DSP_COEF_LARGE_LEAK, 0x2},
|
|
{VILLA_DSP_SDS_SERDES_SRX_DAC_ENABLEB_LSB, 0xD000},
|
|
{VILLA_MSEQ_POWER_DOWN_LSB, 0xFFFF},
|
|
{VILLA_MSEQ_POWER_DOWN_MSB, 0x0},
|
|
{VILLA_MSEQ_CAL_RX_SLICER, 0x80},
|
|
{VILLA_DSP_SDS_SERDES_SRX_DAC_BIAS_SELECT1_MSB, 0x3f},
|
|
{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
|
|
{VILLA_MSEQ_OPTIONS, 0x7},
|
|
|
|
/* set up min value for ffe1 */
|
|
{VILLA_MSEQ_COEF_INIT_SEL, 0x2},
|
|
{VILLA_DSP_SDS_DSP_PRECODEDINITFFE21, 0x41},
|
|
|
|
/* CS4315_sr_rx_pre_eq_set_4in */
|
|
{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
|
|
{VILLA_MSEQ_OPTIONS, 0xf},
|
|
{VILLA_MSEQ_BANKSELECT, 0x4},
|
|
{VILLA_MSEQ_PC, 0x0},
|
|
|
|
/* for lengths from 3.5 to 4.5inches */
|
|
{VILLA_MSEQ_SERDES_PARAM_LSB, 0x0306},
|
|
{VILLA_MSEQ_SPARE25_LSB, 0x0306},
|
|
{VILLA_MSEQ_SPARE21_LSB, 0x2},
|
|
{VILLA_MSEQ_SPARE23_LSB, 0x2},
|
|
{VILLA_MSEQ_CAL_RX_DFE_EQ, 0x0},
|
|
|
|
{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
|
|
{VILLA_MSEQ_OPTIONS, 0x7},
|
|
|
|
/* CS4315_rx_drive_4inch */
|
|
/* for length 4inches */
|
|
{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
|
|
{VILLA_HOST_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
|
|
{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
|
|
|
|
/* CS4315_tx_drive_4inch */
|
|
/* for length 4inches */
|
|
{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
|
|
{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
|
|
{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
|
|
};
|
|
|
|
void cs4340_upload_firmware(struct phy_device *phydev)
|
|
{
|
|
char line_temp[0x50] = {0};
|
|
char reg_addr[0x50] = {0};
|
|
char reg_data[0x50] = {0};
|
|
int i, line_cnt = 0, column_cnt = 0;
|
|
struct cortina_reg_config fw_temp;
|
|
char *addr = NULL;
|
|
|
|
#if defined(CONFIG_SYS_CORTINA_FW_IN_NOR) || \
|
|
defined(CONFIG_SYS_CORTINA_FW_IN_REMOTE)
|
|
|
|
addr = (char *)CONFIG_CORTINA_FW_ADDR;
|
|
#elif defined(CONFIG_SYS_CORTINA_FW_IN_NAND)
|
|
int ret;
|
|
size_t fw_length = CONFIG_CORTINA_FW_LENGTH;
|
|
|
|
addr = malloc(CONFIG_CORTINA_FW_LENGTH);
|
|
ret = nand_read(get_nand_dev_by_index(0),
|
|
(loff_t)CONFIG_CORTINA_FW_ADDR,
|
|
&fw_length, (u_char *)addr);
|
|
if (ret == -EUCLEAN) {
|
|
printf("NAND read of Cortina firmware at 0x%x failed %d\n",
|
|
CONFIG_CORTINA_FW_ADDR, ret);
|
|
}
|
|
#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
|
|
int ret;
|
|
struct spi_flash *ucode_flash;
|
|
|
|
addr = malloc(CONFIG_CORTINA_FW_LENGTH);
|
|
ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
|
|
CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
|
|
if (!ucode_flash) {
|
|
puts("SF: probe for Cortina ucode failed\n");
|
|
} else {
|
|
ret = spi_flash_read(ucode_flash, CONFIG_CORTINA_FW_ADDR,
|
|
CONFIG_CORTINA_FW_LENGTH, addr);
|
|
if (ret)
|
|
puts("SF: read for Cortina ucode failed\n");
|
|
spi_flash_free(ucode_flash);
|
|
}
|
|
#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
|
|
int dev = CONFIG_SYS_MMC_ENV_DEV;
|
|
u32 cnt = CONFIG_CORTINA_FW_LENGTH / 512;
|
|
u32 blk = CONFIG_CORTINA_FW_ADDR / 512;
|
|
struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);
|
|
|
|
if (!mmc) {
|
|
puts("Failed to find MMC device for Cortina ucode\n");
|
|
} else {
|
|
addr = malloc(CONFIG_CORTINA_FW_LENGTH);
|
|
printf("MMC read: dev # %u, block # %u, count %u ...\n",
|
|
dev, blk, cnt);
|
|
mmc_init(mmc);
|
|
(void)mmc->block_dev.block_read(&mmc->block_dev, blk, cnt,
|
|
addr);
|
|
/* flush cache after read */
|
|
flush_cache((ulong)addr, cnt * 512);
|
|
}
|
|
#endif
|
|
|
|
while (*addr != 'Q') {
|
|
i = 0;
|
|
|
|
while (*addr != 0x0a) {
|
|
line_temp[i++] = *addr++;
|
|
if (0x50 < i) {
|
|
printf("Not found Cortina PHY ucode at 0x%p\n",
|
|
(char *)CONFIG_CORTINA_FW_ADDR);
|
|
return;
|
|
}
|
|
}
|
|
|
|
addr++; /* skip '\n' */
|
|
line_cnt++;
|
|
column_cnt = i;
|
|
line_temp[column_cnt] = '\0';
|
|
|
|
if (CONFIG_CORTINA_FW_LENGTH < line_cnt)
|
|
return;
|
|
|
|
for (i = 0; i < column_cnt; i++) {
|
|
if (isspace(line_temp[i++]))
|
|
break;
|
|
}
|
|
|
|
memcpy(reg_addr, line_temp, i);
|
|
memcpy(reg_data, &line_temp[i], column_cnt - i);
|
|
strim(reg_addr);
|
|
strim(reg_data);
|
|
fw_temp.reg_addr = (simple_strtoul(reg_addr, NULL, 0)) & 0xffff;
|
|
fw_temp.reg_value = (simple_strtoul(reg_data, NULL, 0)) &
|
|
0xffff;
|
|
phy_write(phydev, 0x00, fw_temp.reg_addr, fw_temp.reg_value);
|
|
}
|
|
}
|
|
|
|
int cs4340_phy_init(struct phy_device *phydev)
|
|
{
|
|
int timeout = 100; /* 100ms */
|
|
int reg_value;
|
|
|
|
/* step1: BIST test */
|
|
phy_write(phydev, 0x00, VILLA_GLOBAL_MSEQCLKCTRL, 0x0004);
|
|
phy_write(phydev, 0x00, VILLA_GLOBAL_LINE_SOFT_RESET, 0x0000);
|
|
phy_write(phydev, 0x00, VILLA_GLOBAL_BIST_CONTROL, 0x0001);
|
|
while (--timeout) {
|
|
reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_BIST_STATUS);
|
|
if (reg_value & mseq_edc_bist_done) {
|
|
if (0 == (reg_value & mseq_edc_bist_fail))
|
|
break;
|
|
}
|
|
udelay(1000);
|
|
}
|
|
|
|
if (!timeout) {
|
|
printf("%s BIST mseq_edc_bist_done timeout!\n", __func__);
|
|
return -1;
|
|
}
|
|
|
|
/* setp2: upload ucode */
|
|
cs4340_upload_firmware(phydev);
|
|
reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_DWNLD_CHECKSUM_STATUS);
|
|
if (reg_value) {
|
|
debug("%s checksum status failed.\n", __func__);
|
|
return -1;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
int cs4340_config(struct phy_device *phydev)
|
|
{
|
|
cs4340_phy_init(phydev);
|
|
return 0;
|
|
}
|
|
|
|
int cs4340_probe(struct phy_device *phydev)
|
|
{
|
|
phydev->flags = PHY_FLAG_BROKEN_RESET;
|
|
return 0;
|
|
}
|
|
|
|
int cs4340_startup(struct phy_device *phydev)
|
|
{
|
|
phydev->link = 1;
|
|
|
|
/* For now just lie and say it's 10G all the time */
|
|
phydev->speed = SPEED_10000;
|
|
phydev->duplex = DUPLEX_FULL;
|
|
return 0;
|
|
}
|
|
|
|
struct phy_driver cs4340_driver = {
|
|
.name = "Cortina CS4315/CS4340",
|
|
.uid = PHY_UID_CS4340,
|
|
.mask = 0xfffffff0,
|
|
.features = PHY_10G_FEATURES,
|
|
.mmds = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
|
|
MDIO_DEVS_PHYXS | MDIO_DEVS_AN |
|
|
MDIO_DEVS_VEND1 | MDIO_DEVS_VEND2),
|
|
.config = &cs4340_config,
|
|
.probe = &cs4340_probe,
|
|
.startup = &cs4340_startup,
|
|
.shutdown = &gen10g_shutdown,
|
|
};
|
|
|
|
int phy_cortina_init(void)
|
|
{
|
|
phy_register(&cs4340_driver);
|
|
return 0;
|
|
}
|
|
|
|
int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
|
|
{
|
|
int phy_reg;
|
|
bool is_cortina_phy = false;
|
|
|
|
switch (addr) {
|
|
#ifdef CORTINA_PHY_ADDR1
|
|
case CORTINA_PHY_ADDR1:
|
|
#endif
|
|
#ifdef CORTINA_PHY_ADDR2
|
|
case CORTINA_PHY_ADDR2:
|
|
#endif
|
|
#ifdef CORTINA_PHY_ADDR3
|
|
case CORTINA_PHY_ADDR3:
|
|
#endif
|
|
#ifdef CORTINA_PHY_ADDR4
|
|
case CORTINA_PHY_ADDR4:
|
|
#endif
|
|
is_cortina_phy = true;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
/* Cortina PHY has non-standard offset of PHY ID registers */
|
|
if (is_cortina_phy)
|
|
phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_LSB);
|
|
else
|
|
phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
|
|
|
|
if (phy_reg < 0)
|
|
return -EIO;
|
|
|
|
*phy_id = (phy_reg & 0xffff) << 16;
|
|
if (is_cortina_phy)
|
|
phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_MSB);
|
|
else
|
|
phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
|
|
|
|
if (phy_reg < 0)
|
|
return -EIO;
|
|
|
|
*phy_id |= (phy_reg & 0xffff);
|
|
|
|
return 0;
|
|
}
|