mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-07-05 18:56:15 +09:00
4992090ed4
- Remove pinmux definition from pico-imx6ul.c - Enable NET_RANDOM_ETHADDR for temporary solution, because micrel_ksz8xxx driver does not support DM_ETH yet, so cannot read MAC address directly. Before enable DM_ETH: Net: FEC [PRIME] After enable DM_ETH: Net: Warning: using random MAC address - ca:3f:43:8f:67:d4 eth1: ethernet@20b4000 Here is the test commands: => dhcp BOOTP broadcast 1 DHCP client bound to address 10.88.88.94 (139 ms) *** ERROR: `serverip' not set Cannot autoload with TFTPGET => ping 8.8.8.8 Using ethernet@20b4000 device host 8.8.8.8 is alive Signed-off-by: Wig Cheng <wig.cheng@technexion.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
230 lines
6.1 KiB
C
230 lines
6.1 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015 Technexion Ltd.
|
|
*
|
|
* Author: Richard Hu <richard.hu@technexion.com>
|
|
*/
|
|
|
|
#include <init.h>
|
|
#include <net.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/iomux.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/io.h>
|
|
#include <common.h>
|
|
#include <miiphy.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/sizes.h>
|
|
#include <usb.h>
|
|
#include <power/pmic.h>
|
|
#include <power/pfuze3000_pmic.h>
|
|
#include "../../freescale/common/pfuze.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
|
|
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
|
|
PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
|
|
|
|
#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
|
|
PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm)
|
|
|
|
static int setup_fec(void)
|
|
{
|
|
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
|
|
int ret;
|
|
|
|
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
|
|
IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
|
|
|
|
ret = enable_fec_anatop_clock(1, ENET_50MHZ);
|
|
if (ret)
|
|
return ret;
|
|
|
|
enable_enet_clk(1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_VIDEO_MXS
|
|
static iomux_v3_cfg_t const lcd_pads[] = {
|
|
MX6_PAD_LCD_CLK__LCDIF_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_ENABLE__LCDIF_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_HSYNC__LCDIF_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_VSYNC__LCDIF_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA00__LCDIF_DATA00 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA01__LCDIF_DATA01 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA02__LCDIF_DATA02 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA03__LCDIF_DATA03 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA04__LCDIF_DATA04 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA05__LCDIF_DATA05 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA06__LCDIF_DATA06 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA07__LCDIF_DATA07 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA08__LCDIF_DATA08 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA09__LCDIF_DATA09 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA10__LCDIF_DATA10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA11__LCDIF_DATA11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA12__LCDIF_DATA12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA13__LCDIF_DATA13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA14__LCDIF_DATA14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA15__LCDIF_DATA15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA16__LCDIF_DATA16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA17__LCDIF_DATA17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA18__LCDIF_DATA18 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA19__LCDIF_DATA19 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA20__LCDIF_DATA20 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA21__LCDIF_DATA21 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA22__LCDIF_DATA22 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX6_PAD_LCD_DATA23__LCDIF_DATA23 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
/* LCD_BLT_CTRL: GPIO for Brightness adjustment */
|
|
MX6_PAD_NAND_ALE__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
/* LCD_VDD_EN: LCD enabled */
|
|
MX6_PAD_JTAG_TMS__GPIO1_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
void setup_lcd(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
|
|
gpio_request(IMX_GPIO_NR(4, 10), "lcd_brightness");
|
|
gpio_request(IMX_GPIO_NR(1, 11), "lcd_enable");
|
|
/* Set Brightness to high */
|
|
gpio_direction_output(IMX_GPIO_NR(4, 10) , 1);
|
|
/* Set LCD enable to high */
|
|
gpio_direction_output(IMX_GPIO_NR(1, 11) , 1);
|
|
}
|
|
#endif
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
|
|
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = imx_ddr_size();
|
|
|
|
return 0;
|
|
}
|
|
|
|
static iomux_v3_cfg_t const uart6_pads[] = {
|
|
MX6_PAD_CSI_MCLK__UART6_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX6_PAD_CSI_PIXCLK__UART6_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
#define USB_OTHERREGS_OFFSET 0x800
|
|
#define UCTRL_PWR_POL (1 << 9)
|
|
|
|
static iomux_v3_cfg_t const usb_otg_pad[] = {
|
|
MX6_PAD_GPIO1_IO00__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
|
|
};
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart6_pads, ARRAY_SIZE(uart6_pads));
|
|
}
|
|
|
|
static void setup_usb(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(usb_otg_pad, ARRAY_SIZE(usb_otg_pad));
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_DM_PMIC
|
|
int power_init_board(void)
|
|
{
|
|
struct udevice *dev;
|
|
int ret, dev_id, rev_id;
|
|
|
|
ret = pmic_get("pfuze3000", &dev);
|
|
if (ret == -ENODEV)
|
|
return 0;
|
|
if (ret != 0)
|
|
return ret;
|
|
|
|
dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
|
|
rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
|
|
printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
|
|
|
|
/* disable Low Power Mode during standby mode */
|
|
pmic_reg_write(dev, PFUZE3000_LDOGCTL, 0x1);
|
|
|
|
/* SW1B step ramp up time from 2us to 4us/25mV */
|
|
pmic_reg_write(dev, PFUZE3000_SW1BCONF, 0x40);
|
|
|
|
/* SW1B mode to APS/PFM */
|
|
pmic_reg_write(dev, PFUZE3000_SW1BMODE, 0xc);
|
|
|
|
/* SW1B standby voltage set to 0.975V */
|
|
pmic_reg_write(dev, PFUZE3000_SW1BSTBY, 0xb);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int board_usb_phy_mode(int port)
|
|
{
|
|
if (port == 1)
|
|
return USB_INIT_HOST;
|
|
else
|
|
return USB_INIT_DEVICE;
|
|
}
|
|
|
|
int board_ehci_hcd_init(int port)
|
|
{
|
|
u32 *usbnc_usb_ctrl;
|
|
|
|
if (port > 1)
|
|
return -EINVAL;
|
|
|
|
usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
|
|
port * 4);
|
|
|
|
/* Set Power polarity */
|
|
setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
setup_fec();
|
|
setup_usb();
|
|
#ifdef CONFIG_VIDEO_MXS
|
|
setup_lcd();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: PICO-IMX6UL-EMMC\n");
|
|
|
|
return 0;
|
|
}
|