mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-30 22:08:52 +09:00
![Wolfgang Denk](/assets/img/avatar_default.png)
which makes the environment compatible with the hush shell. WARNING: Support for the old '$(...)' syntax will be discontinued in a later version.
395 lines
10 KiB
Plaintext
395 lines
10 KiB
Plaintext
The port was tested on a Sandpoint 8240 X3 board, with U-Boot
|
|
installed in the flash memory of the CPU card. Please use the
|
|
following DIP switch settings:
|
|
|
|
Motherboard:
|
|
|
|
SW1.1: on SW1.2: on SW1.3: on SW1.4: on
|
|
SW1.5: on SW1.6: on SW1.7: on SW1.8: on
|
|
|
|
SW2.1: on SW2.2: on SW2.3: on SW2.4: on
|
|
SW2.5: on SW2.6: on SW2.7: on SW2.8: on
|
|
|
|
|
|
CPU Card:
|
|
|
|
SW2.1: OFF SW2.2: OFF SW2.3: on SW2.4: on
|
|
SW2.5: OFF SW2.6: OFF SW2.7: OFF SW2.8: OFF
|
|
|
|
SW3.1: OFF SW3.2: on SW3.3: OFF SW3.4: OFF
|
|
SW3.5: on SW3.6: OFF SW3.7: OFF SW3.8: on
|
|
|
|
|
|
The followind detailed description of installation and initial steps
|
|
with U-Boot and QNX was provided by Jim Sandoz <sandoz@lucent.com>:
|
|
|
|
|
|
Directions for installing U-Boot on Sandpoint+Unity8240
|
|
using the Abatron BDI2000 BDM/JTAG debugger ...
|
|
|
|
Background and Reference info:
|
|
http://u-boot.sourceforge.net/
|
|
http://www.abatron.ch/
|
|
http://www.abatron.ch/BDI/bdihw.html
|
|
http://www.abatron.ch/DataSheets/BDI2000.pdf
|
|
http://www.abatron.ch/Manuals/ManGdbCOP-2000C.pdf
|
|
http://e-www.motorola.com/collateral/SPX3UM.pdf
|
|
http://e-www.motorola.com/collateral/UNITYX4CONFIG.pdf
|
|
|
|
|
|
Connection Diagram:
|
|
===========
|
|
=== ===== |----- |
|
|
| | <---------------> | | | | |
|
|
|PC | rs232 | BDI |=============[] | |
|
|
| | |2000 | BDM probe | | |
|
|
| | <---------------> | | |----- |
|
|
=== ethernet ===== | |
|
|
| |
|
|
===========
|
|
Sandpoint X3 with
|
|
Unity 8240 proc
|
|
|
|
|
|
PART 1)
|
|
DIP Switch Settings:
|
|
|
|
Sandpoint X3 8240 processor board DIP switch settings, with
|
|
U-Boot to be installed in the flash memory of the CPU card:
|
|
|
|
Motorola Sandpoint X3 Motherboard:
|
|
SW1.1: on SW1.2: on SW1.3: on SW1.4: on
|
|
SW1.5: on SW1.6: on SW1.7: on SW1.8: on
|
|
SW2.1: on SW2.2: on SW2.3: on SW2.4: on
|
|
SW2.5: on SW2.6: on SW2.7: on SW2.8: on
|
|
|
|
Motorola Unity 8240 CPU Card:
|
|
SW2.1: OFF SW2.2: OFF SW2.3: on SW2.4: on
|
|
SW2.5: OFF SW2.6: OFF SW2.7: OFF SW2.8: OFF
|
|
SW3.1: OFF SW3.2: on SW3.3: OFF SW3.4: OFF
|
|
SW3.5: on SW3.6: OFF SW3.7: OFF SW3.8: on
|
|
|
|
|
|
PART 2)
|
|
Connect the BDI2000 Cable to the Sandpoint/Unity 8240:
|
|
|
|
BDM Pin 1 on the Unity 8240 processor board is towards the
|
|
PCI PMC connectors, or away from the socketed SDRAM, i.e.:
|
|
|
|
====================
|
|
| ---------------- |
|
|
| | SDRAM | |
|
|
| | | |
|
|
| ---------------- |
|
|
| |~| |
|
|
| |B| ++++++ |
|
|
| |D| + uP + |
|
|
| |M| +8240+ |
|
|
| ~ 1 ++++++ |
|
|
| |
|
|
| |
|
|
| |
|
|
| PMC conn ====== |
|
|
| ===== ====== |
|
|
| |
|
|
====================
|
|
|
|
|
|
PART 3)
|
|
Setting up the BDI2000, and preparing for TCP/IP network comms:
|
|
|
|
Connect the BDI2000 to the PC using the supplied serial cable.
|
|
Download the BDI2000 software and install it using setup.exe.
|
|
|
|
[Note: of course you can also use the Linux command line tool
|
|
"bdisetup" to configure your BDI2000 - the sources are included on
|
|
the floppy disk that comes with your BDI2000. Just in case you don't
|
|
have any Windows PC's - like me :-) -- wd ]
|
|
|
|
Power up the BDI2000; then follow directions to assign the IP
|
|
address and related network information. Note that U-Boot
|
|
will be loaded to the Sandpoint via tftp. You need to either
|
|
use the Abatron-provided tftp application or provide a tftp
|
|
server (e.g. Linux/Solaris/*BSD) somewhere on your network.
|
|
Once the IP address etc are assigned via the RS232 port,
|
|
further communication with the BDI2000 will happen via the
|
|
ethernet connection.
|
|
|
|
PART 4)
|
|
Making a TCP/IP network connection to the Abatron BDI2000:
|
|
|
|
Telnet to the Abatron BDI2000. Assuming that all of the
|
|
networking info was loaded via RS232 correctly, you will see
|
|
the following (scrolling):
|
|
|
|
- TARGET: waiting for target Vcc
|
|
- TARGET: waiting for target Vcc
|
|
|
|
|
|
PART 5)
|
|
Power up the target Sandpoint:
|
|
If the BDM connections are correct, the following will now appear:
|
|
|
|
- TARGET: waiting for target Vcc
|
|
- TARGET: waiting for target Vcc
|
|
- TARGET: processing power-up delay
|
|
- TARGET: processing user reset request
|
|
- BDI asserts HRESET
|
|
- Reset JTAG controller passed
|
|
- Bypass check: 0x55 => 0xAA
|
|
- Bypass check: 0x55 => 0xAA
|
|
- JTAG exists check passed
|
|
- Target PVR is 0x00810101
|
|
- COP status is 0x01
|
|
- Check running state passed
|
|
- BDI scans COP freeze command
|
|
- BDI removes HRESET
|
|
- COP status is 0x05
|
|
- Check stopped state passed
|
|
- Check LSRL length passed
|
|
- BDI sets breakpoint at 0xFFF00100
|
|
- BDI resumes program execution
|
|
- Waiting for target stop passed
|
|
- TARGET: Target PVR is 0x00810101
|
|
- TARGET: reseting target passed
|
|
- TARGET: processing target startup ....
|
|
- TARGET: processing target startup passed
|
|
BDI>
|
|
|
|
|
|
PART 6)
|
|
Erase the current contents of the flash memory:
|
|
|
|
BDI>era 0xFFF00000
|
|
Erasing flash at 0xfff00000
|
|
Erasing flash passed
|
|
BDI>era 0xFFF04000
|
|
Erasing flash at 0xfff04000
|
|
Erasing flash passed
|
|
BDI>era 0xFFF06000
|
|
Erasing flash at 0xfff06000
|
|
Erasing flash passed
|
|
BDI>era 0xFFF08000
|
|
Erasing flash at 0xfff08000
|
|
Erasing flash passed
|
|
BDI>era 0xFFF10000
|
|
Erasing flash at 0xfff10000
|
|
Erasing flash passed
|
|
BDI>era 0xFFF20000
|
|
Erasing flash at 0xfff20000
|
|
Erasing flash passed
|
|
|
|
|
|
PART 7)
|
|
Program the flash memory with the U-Boot image:
|
|
|
|
BDI>prog 0xFFF00000 u-boot.bin bin
|
|
Programming u-boot.bin , please wait ....
|
|
Programming flash passed
|
|
|
|
|
|
PART 8)
|
|
Connect PC to Sandpoint:
|
|
Using a crossover serial cable, attach the PC serial port to the
|
|
Sandpoint's COM1. Set communications parameters to 8N1 / 9600 baud.
|
|
|
|
|
|
PART 9)
|
|
Reset the Unity and begin U-Boot execution:
|
|
|
|
BDI>reset
|
|
- TARGET: processing user reset request
|
|
- TARGET: Target PVR is 0x00810101
|
|
- TARGET: reseting target passed
|
|
- TARGET: processing target init list ....
|
|
- TARGET: processing target init list passed
|
|
|
|
BDI>go
|
|
|
|
Now see output from U-Boot running, sent via serial port:
|
|
|
|
U-Boot 1.1.4 (Jan 23 2002 - 18:29:19)
|
|
|
|
CPU: MPC8240 Revision 1.1 at 264 MHz: 16 kB I-Cache 16 kB D-Cache
|
|
Board: Sandpoint 8240 Unity
|
|
DRAM: 64 MB
|
|
FLASH: 2 MB
|
|
PCI: scanning bus0 ...
|
|
bus dev fn venID devID class rev MBAR0 MBAR1 IPIN ILINE
|
|
00 00 00 1057 0003 060000 13 00000008 00000000 01 00
|
|
00 0b 00 10ad 0565 060100 10 00000000 00000000 00 00
|
|
00 0f 00 8086 1229 020000 08 80000000 80000001 01 00
|
|
In: serial
|
|
Out: serial
|
|
Err: serial
|
|
=>
|
|
|
|
|
|
PART 10)
|
|
Set and save any required environmental variables, examples of some:
|
|
|
|
=> setenv ethaddr 00:03:47:97:D0:79
|
|
=> setenv bootfile your_qnx_image_here
|
|
=> setenv hostname sandpointX
|
|
=> setenv netmask 255.255.255.0
|
|
=> setenv ipaddr 192.168.0.11
|
|
=> setenv serverip 192.168.0.10
|
|
=> setenv gatewayip=192.168.0.1
|
|
=> saveenv
|
|
Saving Enviroment to Flash...
|
|
Un-Protected 1 sectors
|
|
Erasing Flash...
|
|
done
|
|
Erased 1 sectors
|
|
Writing to Flash... done
|
|
Protected 1 sectors
|
|
=>
|
|
|
|
**** Example environment: ****
|
|
|
|
=> printenv
|
|
baudrate=9600
|
|
bootfile=telemetry
|
|
hostname=sp1
|
|
ethaddr=00:03:47:97:E4:6B
|
|
load=tftp 100000 u-boot.bin
|
|
update=protect off all;era FFF00000 FFF3FFFF;cp.b 100000 FFF00000 ${filesize};saveenv
|
|
filesize=1f304
|
|
gatewayip=145.17.228.1
|
|
netmask=255.255.255.0
|
|
ipaddr=145.17.228.42
|
|
serverip=145.17.242.46
|
|
stdin=serial
|
|
stdout=serial
|
|
stderr=serial
|
|
|
|
Environment size: 332/8188 bytes
|
|
=>
|
|
|
|
here's some text useful stuff for cut-n-paste:
|
|
setenv hostname sandpoint1
|
|
setenv netmask 255.255.255.0
|
|
setenv ipaddr 145.17.228.81
|
|
setenv serverip 145.17.242.46
|
|
setenv gatewayip 145.17.228.1
|
|
saveenv
|
|
|
|
PART 11)
|
|
Test U-Boot by tftp'ing new U-Boot, overwriting current:
|
|
|
|
=> protect off all
|
|
Un-Protect Flash Bank # 1
|
|
=> tftp 100000 u-boot.bin
|
|
eth: Intel i82559 PCI EtherExpressPro @0x80000000(bus=0, device=15, func=0)
|
|
ARP broadcast 1
|
|
TFTP from server 145.17.242.46; our IP address is 145.17.228.42; sending through
|
|
gateway 145.17.228.1
|
|
Filename 'u-boot.bin'.
|
|
Load address: 0x100000
|
|
Loading: #########################
|
|
done
|
|
Bytes transferred = 127628 (1f28c hex)
|
|
=> era all
|
|
Erase Flash Bank # 1
|
|
done
|
|
Erase Flash Bank # 2 - missing
|
|
=> cp.b 0x100000 FFF00000 1f28c
|
|
Copy to Flash... done
|
|
=> saveenv
|
|
Saving Enviroment to Flash...
|
|
Un-Protected 1 sectors
|
|
Erasing Flash...
|
|
done
|
|
Erased 1 sectors
|
|
Writing to Flash... done
|
|
Protected 1 sectors
|
|
=> reset
|
|
|
|
You can put these commands into some environment variables;
|
|
|
|
=> setenv load tftp 100000 u-boot.bin
|
|
=> setenv update protect off all\;era FFF00000 FFF3FFFF\;cp.b 100000 FFF00000 \${filesize}\;saveenv
|
|
=> saveenv
|
|
|
|
Then you just have to type "run load" then "run update"
|
|
|
|
=> run load
|
|
eth: Intel i82559 PCI EtherExpressPro @0x80000000(bus=0, device=15, func=0)
|
|
ARP broadcast 1
|
|
TFTP from server 145.17.242.46; our IP address is 145.17.228.42; sending through
|
|
gateway 145.17.228.1
|
|
Filename 'u-boot.bin'.
|
|
Load address: 0x100000
|
|
Loading: #########################
|
|
done
|
|
Bytes transferred = 127748 (1f304 hex)
|
|
=> run update
|
|
Un-Protect Flash Bank # 1
|
|
Un-Protect Flash Bank # 2
|
|
Erase Flash from 0xfff00000 to 0xfff3ffff
|
|
done
|
|
Erased 7 sectors
|
|
Copy to Flash... done
|
|
Saving Enviroment to Flash...
|
|
Un-Protected 1 sectors
|
|
Erasing Flash...
|
|
done
|
|
Erased 1 sectors
|
|
Writing to Flash... done
|
|
Protected 1 sectors
|
|
=>
|
|
|
|
|
|
PART 12)
|
|
Load OS image (ELF format) via U-Boot using tftp
|
|
|
|
|
|
=> tftp 800000 sandpoint-simple.elf
|
|
eth: Intel i82559 PCI EtherExpressPro @0x80000000(bus=0, device=15, func=0)
|
|
ARP broadcast 1
|
|
TFTP from server 145.17.242.46; our IP address is 145.17.228.42; sending through
|
|
gateway 145.17.228.1
|
|
Filename 'sandpoint-simple.elf'.
|
|
Load address: 0x800000
|
|
Loading: #################################################################
|
|
#################################################################
|
|
#################################################################
|
|
########################
|
|
done
|
|
Bytes transferred = 1120284 (11181c hex)
|
|
==>
|
|
|
|
PART 13)
|
|
Begin OS image execution: (note that unless you have the
|
|
serial parameters of your OS image set to 9600 (i.e. same as
|
|
the U-Boot binary) you will get garbage here until you change
|
|
the serial communications speed.
|
|
|
|
=> bootelf 800000
|
|
Loading @ 0x001f0100 (1120028 bytes)
|
|
## Starting application at 0x001f1d28 ...
|
|
Replace init_hwinfo() with a board specific version
|
|
|
|
Loading QNX6....
|
|
|
|
Header size=0x0000009c, Total Size=0x000005c0, #Cpu=1, Type=1
|
|
<...loader and kernel messages snipped...>
|
|
|
|
Welcome to Neutrino on the Sandpoint
|
|
#
|
|
|
|
|
|
other information:
|
|
|
|
CVS Retrieval Notes:
|
|
|
|
U-Boot's SourceForge CVS repository can be checked out
|
|
through anonymous (pserver) CVS with the following
|
|
instruction set. The module you wish to check out must
|
|
be specified as the modulename. When prompted for a
|
|
password for anonymous, simply press the Enter key.
|
|
|
|
cvs -d:pserver:anonymous@cvs.u-boot.sourceforge.net:/cvsroot/u-boot login
|
|
|
|
cvs -z6 -d:pserver:anonymous@cvs.u-boot.sourceforge.net:/cvsroot/u-boot co -P u-boot
|