mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-15 06:33:45 +09:00
![Lokesh Vutla](/assets/img/avatar_default.png)
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
422 lines
13 KiB
C
422 lines
13 KiB
C
/*
|
|
* (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
|
|
* (C) Copyright 2009, DAVE Srl <www.dave.eu>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
* modifications for the MECP5123 by reinhard.arlt@esd-electronics.com
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* MECP5123 board configuration file
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#define CONFIG_MECP5123 1
|
|
|
|
/*
|
|
* Memory map for the MECP5123 board:
|
|
*
|
|
* 0x0000_0000 - 0x1FFF_FFFF DDR RAM (512 MB)
|
|
* 0x3000_0000 - 0x3001_FFFF SRAM (128 KB)
|
|
* 0x8000_0000 - 0x803F_FFFF IMMR (4 MB)
|
|
* 0x8200_0000 - 0x8200_FFFF VPC-3 (64 KB)
|
|
* 0xFFC0_0000 - 0xFFFF_FFFF NOR Boot FLASH (64 MB)
|
|
*/
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_E300 1 /* E300 Family */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
|
|
|
|
#define CONFIG_SYS_MPC512X_CLKIN 33333333 /* in Hz */
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
#define CONFIG_SYS_IMMR 0x80000000
|
|
#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_IMMR+0x2100)
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
|
|
#define CONFIG_SYS_MEMTEST_END 0x00400000
|
|
|
|
/*
|
|
* DDR Setup - manually set all parameters as there's no SPD etc.
|
|
*/
|
|
#define CONFIG_SYS_DDR_SIZE 512 /* MB */
|
|
|
|
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is sys memory*/
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
|
#define CONFIG_SYS_MAX_RAM_SIZE 0x20000000
|
|
|
|
#define CONFIG_SYS_IOCTRL_MUX_DDR 0x00000036
|
|
|
|
/* DDR Controller Configuration
|
|
*
|
|
* SYS_CFG:
|
|
* [31:31] MDDRC Soft Reset: Diabled
|
|
* [30:30] DRAM CKE pin: Enabled
|
|
* [29:29] DRAM CLK: Enabled
|
|
* [28:28] Command Mode: Enabled (For initialization only)
|
|
* [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10]
|
|
* [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10]
|
|
* [20:19] Read Test: DON'T USE
|
|
* [18:18] Self Refresh: Enabled
|
|
* [17:17] 16bit Mode: Disabled
|
|
* [16:13] Ready Delay: 2
|
|
* [12:12] Half DQS Delay: Disabled
|
|
* [11:11] Quarter DQS Delay: Disabled
|
|
* [10:08] Write Delay: 2
|
|
* [07:07] Early ODT: Disabled
|
|
* [06:06] On DIE Termination: Disabled
|
|
* [05:05] FIFO Overflow Clear: DON'T USE here
|
|
* [04:04] FIFO Underflow Clear: DON'T USE here
|
|
* [03:03] FIFO Overflow Pending: DON'T USE here
|
|
* [02:02] FIFO Underlfow Pending: DON'T USE here
|
|
* [01:01] FIFO Overlfow Enabled: Enabled
|
|
* [00:00] FIFO Underflow Enabled: Enabled
|
|
* TIME_CFG0
|
|
* [31:16] DRAM Refresh Time: 0 CSB clocks
|
|
* [15:8] DRAM Command Time: 0 CSB clocks
|
|
* [07:00] DRAM Precharge Time: 0 CSB clocks
|
|
* TIME_CFG1
|
|
* [31:26] DRAM tRFC:
|
|
* [25:21] DRAM tWR1:
|
|
* [20:17] DRAM tWRT1:
|
|
* [16:11] DRAM tDRR:
|
|
* [10:05] DRAM tRC:
|
|
* [04:00] DRAM tRAS:
|
|
* TIME_CFG2
|
|
* [31:28] DRAM tRCD:
|
|
* [27:23] DRAM tFAW:
|
|
* [22:19] DRAM tRTW1:
|
|
* [18:15] DRAM tCCD:
|
|
* [14:10] DRAM tRTP:
|
|
* [09:05] DRAM tRP:
|
|
* [04:00] DRAM tRPA
|
|
*/
|
|
#define CONFIG_SYS_MDDRC_SYS_CFG 0xEA804A00
|
|
#define CONFIG_SYS_MDDRC_TIME_CFG0 0x06183D2E
|
|
#define CONFIG_SYS_MDDRC_TIME_CFG1 0x68EC1168
|
|
#define CONFIG_SYS_MDDRC_TIME_CFG2 0x34310864
|
|
|
|
#define CONFIG_SYS_DDRCMD_NOP 0x01380000
|
|
#define CONFIG_SYS_DDRCMD_PCHG_ALL 0x01100400
|
|
#define CONFIG_SYS_DDRCMD_EM2 0x01020000
|
|
#define CONFIG_SYS_DDRCMD_EM3 0x01030000
|
|
#define CONFIG_SYS_DDRCMD_EN_DLL 0x01010000
|
|
#define CONFIG_SYS_DDRCMD_RFSH 0x01080000
|
|
#define CONFIG_SYS_MICRON_INIT_DEV_OP 0x01000432
|
|
#define CONFIG_SYS_DDRCMD_OCD_DEFAULT 0x01010780
|
|
|
|
/* DDR Priority Manager Configuration */
|
|
#define CONFIG_SYS_MDDRCGRP_PM_CFG1 0x00077777
|
|
#define CONFIG_SYS_MDDRCGRP_PM_CFG2 0x00000000
|
|
#define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG 0x00000001
|
|
#define CONFIG_SYS_MDDRCGRP_LUT0_MU 0xFFEEDDCC
|
|
#define CONFIG_SYS_MDDRCGRP_LUT0_ML 0xBBAAAAAA
|
|
#define CONFIG_SYS_MDDRCGRP_LUT1_MU 0x66666666
|
|
#define CONFIG_SYS_MDDRCGRP_LUT1_ML 0x55555555
|
|
#define CONFIG_SYS_MDDRCGRP_LUT2_MU 0x44444444
|
|
#define CONFIG_SYS_MDDRCGRP_LUT2_ML 0x44444444
|
|
#define CONFIG_SYS_MDDRCGRP_LUT3_MU 0x55555555
|
|
#define CONFIG_SYS_MDDRCGRP_LUT3_ML 0x55555558
|
|
#define CONFIG_SYS_MDDRCGRP_LUT4_MU 0x11111111
|
|
#define CONFIG_SYS_MDDRCGRP_LUT4_ML 0x11111122
|
|
#define CONFIG_SYS_MDDRCGRP_LUT0_AU 0xaaaaaaaa
|
|
#define CONFIG_SYS_MDDRCGRP_LUT0_AL 0xaaaaaaaa
|
|
#define CONFIG_SYS_MDDRCGRP_LUT1_AU 0x66666666
|
|
#define CONFIG_SYS_MDDRCGRP_LUT1_AL 0x66666666
|
|
#define CONFIG_SYS_MDDRCGRP_LUT2_AU 0x11111111
|
|
#define CONFIG_SYS_MDDRCGRP_LUT2_AL 0x11111111
|
|
#define CONFIG_SYS_MDDRCGRP_LUT3_AU 0x11111111
|
|
#define CONFIG_SYS_MDDRCGRP_LUT3_AL 0x11111111
|
|
#define CONFIG_SYS_MDDRCGRP_LUT4_AU 0x11111111
|
|
#define CONFIG_SYS_MDDRCGRP_LUT4_AL 0x11111111
|
|
|
|
/*
|
|
* NOR FLASH on the Local Bus
|
|
*/
|
|
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
|
|
|
|
#define CONFIG_SYS_FLASH_BASE 0xFFC00000 /* start of FLASH */
|
|
#define CONFIG_SYS_FLASH_SIZE 0x00400000 /* max flash size */
|
|
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
|
|
|
|
#undef CONFIG_SYS_FLASH_CHECKSUM
|
|
|
|
/*
|
|
* NAND FLASH
|
|
* drivers/mtd/nand/mpc5121_nfc.c (rev 2 silicon only)
|
|
*/
|
|
#define CONFIG_CMD_NAND
|
|
#define CONFIG_NAND_MPC5121_NFC
|
|
#define CONFIG_SYS_NAND_BASE 0x40000000
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
|
|
/*
|
|
* Configuration parameters for MPC5121 NAND driver
|
|
*/
|
|
#define CONFIG_FSL_NFC_WIDTH 1
|
|
#define CONFIG_FSL_NFC_WRITE_SIZE 2048
|
|
#define CONFIG_FSL_NFC_SPARE_SIZE 64
|
|
#define CONFIG_FSL_NFC_CHIPS 1
|
|
|
|
#define CONFIG_SYS_SRAM_BASE 0x30000000
|
|
#define CONFIG_SYS_SRAM_SIZE 0x00020000 /* 128 KB */
|
|
|
|
/* Initialize Local Window for NOR FLASH access */
|
|
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
|
|
|
|
/* ALE active low, data size 4bytes */
|
|
#define CONFIG_SYS_CS0_CFG 0x05051150
|
|
|
|
/* Use not alternative CS timing */
|
|
#define CONFIG_SYS_CS_ALETIMING 0x00000000
|
|
|
|
/* ALE active low, data size 4bytes */
|
|
#define CONFIG_SYS_CS1_CFG 0x1f1f3090
|
|
#define CONFIG_SYS_VPC3_BASE 0x82000000 /* start of VPC3 space */
|
|
#define CONFIG_SYS_VPC3_SIZE 0x00010000 /* max VPC3 size */
|
|
/* Initialize Local Window for VPC3 access */
|
|
#define CONFIG_SYS_CS1_START CONFIG_SYS_VPC3_BASE
|
|
#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_VPC3_SIZE
|
|
|
|
/* Use SRAM for initial stack */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SRAM_BASE /* Init RAM addr */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_SRAM_SIZE
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of monitor */
|
|
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Monitor length */
|
|
#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Malloc size */
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1
|
|
|
|
/*
|
|
* Serial console configuration
|
|
*/
|
|
#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */
|
|
#define CONFIG_SYS_PSC3
|
|
#if CONFIG_PSC_CONSOLE != 3
|
|
#error CONFIG_PSC_CONSOLE must be 3
|
|
#endif
|
|
#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
|
|
#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE
|
|
#define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR
|
|
#define CONSOLE_FIFO_RX_SIZE FIFOC_PSC3_RX_SIZE
|
|
#define CONSOLE_FIFO_RX_ADDR FIFOC_PSC3_RX_ADDR
|
|
|
|
/*
|
|
* Clocks in use
|
|
*/
|
|
#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN | \
|
|
CLOCK_SCCR1_LPC_EN | \
|
|
CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \
|
|
CLOCK_SCCR1_PSCFIFO_EN | \
|
|
CLOCK_SCCR1_DDR_EN | \
|
|
CLOCK_SCCR1_FEC_EN | \
|
|
CLOCK_SCCR1_NFC_EN | \
|
|
CLOCK_SCCR1_PCI_EN | \
|
|
CLOCK_SCCR1_TPR_EN)
|
|
|
|
#define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN | \
|
|
CLOCK_SCCR2_I2C_EN)
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
|
|
|
/* I2C */
|
|
#define CONFIG_HARD_I2C /* I2C with hardware support */
|
|
#define CONFIG_I2C_MULTI_BUS
|
|
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */
|
|
|
|
/*
|
|
* IIM - IC Identification Module
|
|
*/
|
|
#undef CONFIG_FSL_IIM
|
|
|
|
/*
|
|
* EEPROM configuration
|
|
*/
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
|
|
#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */
|
|
|
|
/*
|
|
* Ethernet configuration
|
|
*/
|
|
#define CONFIG_MPC512x_FEC 1
|
|
#define CONFIG_PHY_ADDR 0x1
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_FEC_AN_TIMEOUT 1
|
|
#define CONFIG_HAS_ETH0
|
|
|
|
/*
|
|
* Configure on-board RTC
|
|
*/
|
|
#define CONFIG_SYS_RTC_BUS_NUM 0x01
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x32
|
|
#define CONFIG_RTC_RX8025
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */
|
|
#define CONFIG_ENV_SIZE 0x1000
|
|
#define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */
|
|
|
|
#define CONFIG_LOADS_ECHO /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
|
|
|
|
#define CONFIG_CMD_REGINFO
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_DATE
|
|
#undef CONFIG_CMD_FUSE
|
|
#undef CONFIG_CMD_IDE
|
|
#define CONFIG_CMD_JFFS2
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
/*
|
|
* Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
|
|
* For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set
|
|
* to 0xFFFF, watchdog timeouts after about 64s. For details refer
|
|
* to chapter 36 of the MPC5121e Reference Manual.
|
|
*/
|
|
/* #define CONFIG_WATCHDOG */ /* enable watchdog */
|
|
#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
|
|
#ifdef CONFIG_CMD_KGDB
|
|
# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
|
|
sizeof(CONFIG_SYS_PROMPT) + 16)
|
|
/* max number of command args */
|
|
#define CONFIG_SYS_MAXARGS 32
|
|
/* Boot Argument Buffer Size */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 256 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Linux initial memory map */
|
|
|
|
/* Cache Configuration */
|
|
#define CONFIG_SYS_DCACHE_SIZE 32768
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32
|
|
#ifdef CONFIG_CMD_KGDB
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 5
|
|
#endif
|
|
|
|
#define CONFIG_SYS_HID0_INIT 0x000000000
|
|
#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
|
|
#define CONFIG_SYS_HID2 HID2_HBE
|
|
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
|
|
|
|
#ifdef CONFIG_CMD_KGDB
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
|
|
#endif
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_TIMESTAMP
|
|
|
|
#define CONFIG_HOSTNAME mecp512x
|
|
#define CONFIG_BOOTFILE "/tftpboot/mecp512x/uImage"
|
|
#define CONFIG_ROOTPATH "/tftpboot/mecp512x/target_root"
|
|
|
|
#define CONFIG_LOADADDR 400000 /* def. location for tftp and bootm */
|
|
|
|
#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
|
|
|
|
#define CONFIG_PREBOOT "echo;" \
|
|
"echo Welcome to MECP5123" \
|
|
"echo"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"u-boot_addr_r=200000\0" \
|
|
"kernel_addr_r=600000\0" \
|
|
"fdt_addr_r=880000\0" \
|
|
"ramdisk_addr_r=900000\0" \
|
|
"u-boot_addr=FFF00000\0" \
|
|
"kernel_addr=FFC40000\0" \
|
|
"fdt_addr=FFEC0000\0" \
|
|
"ramdisk_addr=FC040000\0" \
|
|
"ramdiskfile=/tftpboot/mecp512x/uRamdisk\0" \
|
|
"u-boot=/tftpboot/mecp512x/u-boot.bin\0" \
|
|
"bootfile=/tftpboot/mecp512x/uImage\0" \
|
|
"fdtfile=/tftpboot/mecp512x/mecp512x.dtb\0" \
|
|
"rootpath=/tftpboot/mecp512x/target_root\n" \
|
|
"netdev=eth0\0" \
|
|
"consdev=ttyPSC0\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addtty=setenv bootargs ${bootargs} " \
|
|
"console=${consdev},${baudrate}\0" \
|
|
"flash_nfs=run nfsargs addip addtty;" \
|
|
"bootm ${kernel_addr} - ${fdt_addr}\0" \
|
|
"flash_self=run ramargs addip addtty;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
|
|
"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
|
|
"tftp ${fdt_addr_r} ${fdtfile};" \
|
|
"run nfsargs addip addtty;" \
|
|
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
|
|
"net_self=tftp ${kernel_addr_r} ${bootfile};" \
|
|
"tftp ${ramdisk_addr_r} ${ramdiskfile};" \
|
|
"tftp ${fdt_addr_r} ${fdtfile};" \
|
|
"run ramargs addip addtty;" \
|
|
"bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
|
|
"load=tftp ${u-boot_addr_r} ${u-boot}\0" \
|
|
"update=protect off ${u-boot_addr} +${filesize};" \
|
|
"era ${u-boot_addr} +${filesize};" \
|
|
"cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0" \
|
|
"upd=run load update\0" \
|
|
""
|
|
|
|
#define CONFIG_BOOTCOMMAND "run flash_self"
|
|
|
|
#define OF_CPU "PowerPC,5121@0"
|
|
#define OF_SOC_COMPAT "fsl,mpc5121-immr"
|
|
#define OF_TBCLK (bd->bi_busfreq / 4)
|
|
#define OF_STDOUT_PATH "/soc@80000000/serial@11300"
|
|
|
|
#endif /* __CONFIG_H */
|