mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-20 08:58:52 +09:00
![Anton Vorontsov](/assets/img/avatar_default.png)
move the BRx_* and ORx_* left behind in mpc85xx.h The same is needed for mpc8xx.h and mpc8260.h (defines are almost the same, just few differences which needs some attention though). But the bad news for mpc8xx and mpc8260 is that there are a lot of users of these defines. So this cleanup I'll leave for the "better times". Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
578 lines
17 KiB
C
578 lines
17 KiB
C
/*
|
|
* Copyright (C) 2006 Freescale Semiconductor, Inc.
|
|
* Dave Liu <daveliu@freescale.com>
|
|
*
|
|
* Copyright (C) 2007 Logic Product Development, Inc.
|
|
* Peter Barada <peterb@logicpd.com>
|
|
*
|
|
* Copyright (C) 2007 MontaVista Software, Inc.
|
|
* Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_E300 1 /* E300 family */
|
|
#define CONFIG_QE 1 /* Has QE */
|
|
#define CONFIG_MPC83XX 1 /* MPC83XX family */
|
|
#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
|
|
#define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */
|
|
|
|
/*
|
|
* System Clock Setup
|
|
*/
|
|
#ifdef CONFIG_CLKIN_33MHZ
|
|
#define CONFIG_83XX_CLKIN 33333333
|
|
#define CONFIG_SYS_CLK_FREQ 33333333
|
|
#define PCI_33M 1
|
|
#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1
|
|
#else
|
|
#define CONFIG_83XX_CLKIN 66000000
|
|
#define CONFIG_SYS_CLK_FREQ 66000000
|
|
#define PCI_66M 1
|
|
#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1
|
|
#endif /* CONFIG_CLKIN_33MHZ */
|
|
|
|
/*
|
|
* Hardware Reset Configuration Word
|
|
*/
|
|
#define CFG_HRCW_LOW (\
|
|
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
|
|
HRCWL_DDR_TO_SCB_CLK_1X1 |\
|
|
HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\
|
|
HRCWL_CORE_TO_CSB_2X1 |\
|
|
HRCWL_CE_TO_PLL_1X15)
|
|
|
|
#define CFG_HRCW_HIGH (\
|
|
HRCWH_PCI_HOST |\
|
|
HRCWH_PCI1_ARBITER_ENABLE |\
|
|
HRCWH_PCICKDRV_ENABLE |\
|
|
HRCWH_CORE_ENABLE |\
|
|
HRCWH_FROM_0X00000100 |\
|
|
HRCWH_BOOTSEQ_DISABLE |\
|
|
HRCWH_SW_WATCHDOG_DISABLE |\
|
|
HRCWH_ROM_LOC_LOCAL_16BIT |\
|
|
HRCWH_SECONDARY_DDR_DISABLE |\
|
|
HRCWH_BIG_ENDIAN |\
|
|
HRCWH_LALE_EARLY)
|
|
|
|
/*
|
|
* System IO Config
|
|
*/
|
|
#define CFG_SICRH 0x00000000
|
|
#define CFG_SICRL 0x40000000
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
|
|
#define CONFIG_BOARD_EARLY_INIT_R
|
|
|
|
/*
|
|
* IMMR new address
|
|
*/
|
|
#define CFG_IMMR 0xE0000000
|
|
|
|
/*
|
|
* DDR Setup
|
|
*/
|
|
#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
|
|
#define CFG_SDRAM_BASE CFG_DDR_BASE
|
|
#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
|
|
#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
|
|
DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
|
|
|
|
#define CFG_83XX_DDR_USES_CS0
|
|
|
|
#define CONFIG_DDR_ECC /* support DDR ECC function */
|
|
#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
|
|
|
|
/*
|
|
* DDRCDR - DDR Control Driver Register
|
|
*/
|
|
#define CFG_DDRCDR_VALUE 0x80080001
|
|
|
|
#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */
|
|
|
|
/*
|
|
* Manually set up DDR parameters
|
|
*/
|
|
#define CONFIG_DDR_II
|
|
#define CFG_DDR_SIZE 256 /* MB */
|
|
#define CFG_DDR_CS0_BNDS 0x0000000f
|
|
#define CFG_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | \
|
|
CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS)
|
|
#define CFG_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | SDRAM_CFG_ECC_EN)
|
|
#define CFG_DDR_SDRAM_CFG2 0x00001000
|
|
#define CFG_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
|
|
#define CFG_DDR_INTERVAL ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
|
|
(1115 << SDRAM_INTERVAL_REFINT_SHIFT))
|
|
#define CFG_DDR_MODE 0x47800432
|
|
#define CFG_DDR_MODE2 0x8000c000
|
|
|
|
#define CFG_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
|
|
(9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
|
|
(3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
|
|
(3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
|
|
(0 << TIMING_CFG0_WWT_SHIFT) | \
|
|
(0 << TIMING_CFG0_RRT_SHIFT) | \
|
|
(0 << TIMING_CFG0_WRT_SHIFT) | \
|
|
(0 << TIMING_CFG0_RWT_SHIFT))
|
|
|
|
#define CFG_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_30) | \
|
|
( 2 << TIMING_CFG1_WRTORD_SHIFT) | \
|
|
( 2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
|
|
( 3 << TIMING_CFG1_WRREC_SHIFT) | \
|
|
(10 << TIMING_CFG1_REFREC_SHIFT) | \
|
|
( 3 << TIMING_CFG1_ACTTORW_SHIFT) | \
|
|
( 8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
|
|
( 3 << TIMING_CFG1_PRETOACT_SHIFT))
|
|
|
|
#define CFG_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
|
|
(4 << TIMING_CFG2_CKE_PLS_SHIFT) | \
|
|
(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
|
|
(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
|
|
(2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
|
|
(0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
|
|
(0 << TIMING_CFG2_CPO_SHIFT))
|
|
|
|
#define CFG_DDR_TIMING_3 0x00000000
|
|
|
|
/*
|
|
* Memory test
|
|
*/
|
|
#undef CFG_DRAM_TEST /* memory test, takes time */
|
|
#define CFG_MEMTEST_START 0x00000000 /* memtest region */
|
|
#define CFG_MEMTEST_END 0x00100000
|
|
|
|
/*
|
|
* The reserved memory
|
|
*/
|
|
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
|
|
#define CFG_FLASH_BASE 0xFF800000 /* FLASH base address */
|
|
|
|
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
|
|
#define CFG_RAMBOOT
|
|
#else
|
|
#undef CFG_RAMBOOT
|
|
#endif
|
|
|
|
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
|
|
#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Initial RAM Base Address Setup
|
|
*/
|
|
#define CFG_INIT_RAM_LOCK 1
|
|
#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
|
|
#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */
|
|
#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
|
|
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
|
|
|
|
/*
|
|
* Local Bus Configuration & Clock Setup
|
|
*/
|
|
#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
|
|
#define CFG_LBC_LBCR 0x00000000
|
|
|
|
/*
|
|
* FLASH on the Local Bus
|
|
*/
|
|
#define CFG_FLASH_CFI /* use the Common Flash Interface */
|
|
#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
|
|
#define CFG_FLASH_SIZE 8 /* max FLASH size is 32M */
|
|
#define CFG_FLASH_PROTECTION 1 /* Use intel Flash protection. */
|
|
|
|
#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
|
|
#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */
|
|
|
|
#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \
|
|
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
|
|
BR_V) /* valid */
|
|
#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
|
|
OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
|
|
OR_GPCM_XACS | OR_GPCM_SCY_15 | \
|
|
OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
|
|
|
|
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */
|
|
|
|
#undef CFG_FLASH_CHECKSUM
|
|
|
|
/*
|
|
* NAND flash on the local bus
|
|
*/
|
|
#define CFG_NAND_BASE 0x60000000
|
|
#define CONFIG_CMD_NAND 1
|
|
#define CONFIG_NAND_FSL_UPM 1
|
|
#define CFG_MAX_NAND_DEVICE 1
|
|
#define NAND_MAX_CHIPS 1
|
|
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
|
|
|
#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
|
|
#define CFG_LBLAWAR1_PRELIM 0x8000001b /* Access window size 4K */
|
|
|
|
/* Port size 8 bit, UPMA */
|
|
#define CFG_BR1_PRELIM (CFG_NAND_BASE | 0x00000881)
|
|
#define CFG_OR1_PRELIM 0xfc000001
|
|
|
|
/*
|
|
* Fujitsu MB86277 (MINT) graphics controller
|
|
*/
|
|
#define CFG_VIDEO_BASE 0x70000000
|
|
|
|
#define CFG_LBLAWBAR2_PRELIM CFG_VIDEO_BASE
|
|
#define CFG_LBLAWAR2_PRELIM 0x80000019 /* Access window size 64MB */
|
|
|
|
/* Port size 32 bit, UPMB */
|
|
#define CFG_BR2_PRELIM (CFG_VIDEO_BASE | 0x000018a1) /* PS=11, UPMB */
|
|
#define CFG_OR2_PRELIM 0xfc000001 /* (64MB, EAD=1) */
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1
|
|
#undef CONFIG_SERIAL_SOFTWARE_FIFO
|
|
#define CFG_NS16550
|
|
#define CFG_NS16550_SERIAL
|
|
#define CFG_NS16550_REG_SIZE 1
|
|
#define CFG_NS16550_CLK get_bus_freq(0)
|
|
|
|
#define CFG_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200,}
|
|
|
|
#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
|
|
#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
|
/* Use the HUSH parser */
|
|
#define CFG_HUSH_PARSER
|
|
#ifdef CFG_HUSH_PARSER
|
|
#define CFG_PROMPT_HUSH_PS2 "> "
|
|
#endif
|
|
|
|
/* Pass open firmware flat tree */
|
|
#define CONFIG_OF_LIBFDT 1
|
|
#define CONFIG_OF_BOARD_SETUP 1
|
|
#define CONFIG_OF_STDOUT_VIA_ALIAS
|
|
|
|
/* I2C */
|
|
#define CONFIG_HARD_I2C /* I2C with hardware support */
|
|
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
|
|
#define CONFIG_FSL_I2C
|
|
#define CONFIG_I2C_MULTI_BUS
|
|
#define CONFIG_I2C_CMD_TREE
|
|
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CFG_I2C_SLAVE 0x7F
|
|
#define CFG_I2C_NOPROBES {{0x52}} /* Don't probe these addrs */
|
|
#define CFG_I2C_OFFSET 0x3000
|
|
#define CFG_I2C2_OFFSET 0x3100
|
|
|
|
/*
|
|
* General PCI
|
|
* Addresses are mapped 1-1.
|
|
*/
|
|
#define CONFIG_PCI
|
|
#define CONFIG_83XX_GENERIC_PCI 1
|
|
|
|
#define CFG_PCI1_MEM_BASE 0x80000000
|
|
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
|
|
#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CFG_PCI1_MMIO_BASE 0x90000000
|
|
#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
|
|
#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
|
|
#define CFG_PCI1_IO_BASE 0xE0300000
|
|
#define CFG_PCI1_IO_PHYS 0xE0300000
|
|
#define CFG_PCI1_IO_SIZE 0x100000 /* 1M */
|
|
|
|
#ifdef CONFIG_PCI
|
|
|
|
#define CONFIG_NET_MULTI
|
|
#define CONFIG_PCI_PNP /* do pci plug-and-play */
|
|
|
|
#undef CONFIG_EEPRO100
|
|
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
|
|
|
|
#endif /* CONFIG_PCI */
|
|
|
|
|
|
#ifndef CONFIG_NET_MULTI
|
|
#define CONFIG_NET_MULTI 1
|
|
#endif
|
|
|
|
/*
|
|
* QE UEC ethernet configuration
|
|
*/
|
|
#define CONFIG_UEC_ETH
|
|
#define CONFIG_ETHPRIME "FSL UEC0"
|
|
|
|
#define CONFIG_UEC_ETH1 /* GETH1 */
|
|
|
|
#ifdef CONFIG_UEC_ETH1
|
|
#define CFG_UEC1_UCC_NUM 0 /* UCC1 */
|
|
#define CFG_UEC1_RX_CLK QE_CLK_NONE
|
|
#define CFG_UEC1_TX_CLK QE_CLK9
|
|
#define CFG_UEC1_ETH_TYPE GIGA_ETH
|
|
#define CFG_UEC1_PHY_ADDR 2
|
|
#define CFG_UEC1_INTERFACE_MODE ENET_1000_RGMII_RXID
|
|
#endif
|
|
|
|
#define CONFIG_UEC_ETH2 /* GETH2 */
|
|
|
|
#ifdef CONFIG_UEC_ETH2
|
|
#define CFG_UEC2_UCC_NUM 1 /* UCC2 */
|
|
#define CFG_UEC2_RX_CLK QE_CLK_NONE
|
|
#define CFG_UEC2_TX_CLK QE_CLK4
|
|
#define CFG_UEC2_ETH_TYPE GIGA_ETH
|
|
#define CFG_UEC2_PHY_ADDR 4
|
|
#define CFG_UEC2_INTERFACE_MODE ENET_1000_RGMII_RXID
|
|
#endif
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
|
|
#ifndef CFG_RAMBOOT
|
|
#define CFG_ENV_IS_IN_FLASH 1
|
|
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
|
|
#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
|
|
#define CFG_ENV_SIZE 0x20000
|
|
#else /* CFG_RAMBOOT */
|
|
#define CFG_NO_FLASH 1 /* Flash is not usable now */
|
|
#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
|
|
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
|
|
#define CFG_ENV_SIZE 0x2000
|
|
#endif /* CFG_RAMBOOT */
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_ASKENV
|
|
#define CONFIG_CMD_DHCP
|
|
|
|
#if defined(CONFIG_PCI)
|
|
#define CONFIG_CMD_PCI
|
|
#endif
|
|
|
|
#if defined(CFG_RAMBOOT)
|
|
#undef CONFIG_CMD_ENV
|
|
#undef CONFIG_CMD_LOADS
|
|
#endif
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CFG_LONGHELP /* undef to save memory */
|
|
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
|
|
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
|
|
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
|
|
#define CFG_MAXARGS 16 /* max number of command args */
|
|
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
|
|
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*
|
|
* Core HID Setup
|
|
*/
|
|
#define CFG_HID0_INIT 0x000000000
|
|
#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
|
|
#define CFG_HID2 HID2_HBE
|
|
|
|
/*
|
|
* MMU Setup
|
|
*/
|
|
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
|
|
|
|
/* DDR: cache cacheable */
|
|
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
|
|
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
#define CFG_DBAT0L CFG_IBAT0L
|
|
#define CFG_DBAT0U CFG_IBAT0U
|
|
|
|
/* IMMRBAR & PCI IO: cache-inhibit and guarded */
|
|
#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \
|
|
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
|
#define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
|
|
#define CFG_DBAT1L CFG_IBAT1L
|
|
#define CFG_DBAT1U CFG_IBAT1U
|
|
|
|
/* NAND: cache-inhibit and guarded */
|
|
#define CFG_IBAT2L (CFG_NAND_BASE | BATL_PP_10 | BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CFG_IBAT2U (CFG_NAND_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
|
|
#define CFG_DBAT2L CFG_IBAT2L
|
|
#define CFG_DBAT2U CFG_IBAT2U
|
|
|
|
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
|
|
#define CFG_IBAT3L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
|
|
#define CFG_IBAT3U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
|
|
#define CFG_DBAT3L (CFG_FLASH_BASE | BATL_PP_10 | \
|
|
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
|
#define CFG_DBAT3U CFG_IBAT3U
|
|
|
|
/* Stack in dcache: cacheable, no memory coherence */
|
|
#define CFG_IBAT4L (CFG_INIT_RAM_ADDR | BATL_PP_10)
|
|
#define CFG_IBAT4U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
|
|
#define CFG_DBAT4L CFG_IBAT4L
|
|
#define CFG_DBAT4U CFG_IBAT4U
|
|
|
|
#define CFG_IBAT5L (CFG_VIDEO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | \
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CFG_IBAT5U (CFG_VIDEO_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
|
|
#define CFG_DBAT5L CFG_IBAT5L
|
|
#define CFG_DBAT5U CFG_IBAT5U
|
|
|
|
#ifdef CONFIG_PCI
|
|
/* PCI MEM space: cacheable */
|
|
#define CFG_IBAT6L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
|
|
#define CFG_IBAT6U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
#define CFG_DBAT6L CFG_IBAT6L
|
|
#define CFG_DBAT6U CFG_IBAT6U
|
|
/* PCI MMIO space: cache-inhibit and guarded */
|
|
#define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
|
|
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
|
#define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
#define CFG_DBAT7L CFG_IBAT7L
|
|
#define CFG_DBAT7U CFG_IBAT7U
|
|
#else /* CONFIG_PCI */
|
|
#define CFG_IBAT6L (0)
|
|
#define CFG_IBAT6U (0)
|
|
#define CFG_IBAT7L (0)
|
|
#define CFG_IBAT7U (0)
|
|
#define CFG_DBAT6L CFG_IBAT6L
|
|
#define CFG_DBAT6U CFG_IBAT6U
|
|
#define CFG_DBAT7L CFG_IBAT7L
|
|
#define CFG_DBAT7U CFG_IBAT7U
|
|
#endif /* CONFIG_PCI */
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
|
|
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
|
|
#endif
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#if defined(CONFIG_UEC_ETH)
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_HAS_ETH1
|
|
#define CONFIG_HAS_ETH2
|
|
#define CONFIG_HAS_ETH3
|
|
#define CONFIG_ETHADDR 00:04:9f:ef:01:01
|
|
#define CONFIG_ETH1ADDR 00:04:9f:ef:01:02
|
|
#define CONFIG_ETH2ADDR 00:04:9f:ef:01:03
|
|
#define CONFIG_ETH3ADDR 00:04:9f:ef:01:04
|
|
#endif
|
|
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
#define CONFIG_LOADADDR a00000
|
|
#define CONFIG_HOSTNAME mpc8360erdk
|
|
#define CONFIG_BOOTFILE uImage
|
|
|
|
#define CONFIG_IPADDR 10.0.0.99
|
|
#define CONFIG_SERVERIP 10.0.0.2
|
|
#define CONFIG_GATEWAYIP 10.0.0.2
|
|
#define CONFIG_NETMASK 255.255.255.0
|
|
#define CONFIG_ROOTPATH /nfsroot/
|
|
|
|
#define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */
|
|
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0"\
|
|
"consoledev=ttyS0\0"\
|
|
"loadaddr=a00000\0"\
|
|
"fdtaddr=900000\0"\
|
|
"fdtfile=dtb\0"\
|
|
"fsfile=fs\0"\
|
|
"ubootfile=u-boot.bin\0"\
|
|
"mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),-(rootfs)\0"\
|
|
"setbootargs=setenv bootargs console=$consoledev,$baudrate "\
|
|
"$mtdparts panic=1\0"\
|
|
"adddhcpargs=setenv bootargs $bootargs ip=on\0"\
|
|
"addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"\
|
|
"$gatewayip:$netmask:$hostname:$netdev:off "\
|
|
"root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"\
|
|
"addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 "\
|
|
"rootfstype=jffs2 rw\0"\
|
|
"tftp_get_uboot=tftp 100000 $ubootfile\0"\
|
|
"tftp_get_kernel=tftp $loadaddr $bootfile\0"\
|
|
"tftp_get_dtb=tftp $fdtaddr $fdtfile\0"\
|
|
"tftp_get_fs=tftp c00000 $fsfile\0"\
|
|
"nand_erase_kernel=nand erase 0 400000\0"\
|
|
"nand_erase_dtb=nand erase 400000 20000\0"\
|
|
"nand_erase_fs=nand erase 420000 3be0000\0"\
|
|
"nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0"\
|
|
"nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0"\
|
|
"nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0"\
|
|
"nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0"\
|
|
"nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0"\
|
|
"nor_reflash=protect off ff800000 ff87ffff ; erase ff800000 ff87ffff ; "\
|
|
"cp.b 100000 ff800000 $filesize\0"\
|
|
"nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel "\
|
|
"nand_write_kernel\0"\
|
|
"nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\
|
|
"nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0"\
|
|
"nand_reflash=run nand_reflash_kernel nand_reflash_dtb "\
|
|
"nand_reflash_fs\0"\
|
|
"boot_m=bootm $loadaddr - $fdtaddr\0"\
|
|
"dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\
|
|
"nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
|
|
"boot_m\0"\
|
|
"nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\
|
|
"boot_m\0"\
|
|
""
|
|
|
|
#define CONFIG_BOOTCOMMAND "run dhcpboot"
|
|
|
|
#endif /* __CONFIG_H */
|