mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-10-06 03:20:41 +09:00
cd8341b7eb
Schematic indicates GPIO5_7 is to be used for VTT regulator control rather than GPIO0_21 so modify enable_vtt_regulator to reflect this. Without this some boards will experience DDR3 corruption and fail to boot. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [trini: Rework patch against mainline] Signed-off-by: Tom Rini <trini@ti.com>
59 lines
1.5 KiB
C
59 lines
1.5 KiB
C
/*
|
|
* mux.c
|
|
*
|
|
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/mux.h>
|
|
#include "board.h"
|
|
|
|
static struct module_pin_mux uart0_pin_mux[] = {
|
|
{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE | SLEWCTRL)},
|
|
{OFFSET(uart0_txd), (MODE(0) | PULLUDDIS | PULLUP_EN | SLEWCTRL)},
|
|
{-1},
|
|
};
|
|
|
|
static struct module_pin_mux mmc0_pin_mux[] = {
|
|
{OFFSET(mmc0_clk), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* MMC0_CLK */
|
|
{OFFSET(mmc0_cmd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_CMD */
|
|
{OFFSET(mmc0_dat0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_DAT0 */
|
|
{OFFSET(mmc0_dat1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_DAT1 */
|
|
{OFFSET(mmc0_dat2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_DAT2 */
|
|
{OFFSET(mmc0_dat3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_DAT3 */
|
|
{-1},
|
|
};
|
|
|
|
static struct module_pin_mux i2c0_pin_mux[] = {
|
|
{OFFSET(i2c0_sda), (MODE(0) | PULLUP_EN | RXACTIVE | SLEWCTRL)},
|
|
{OFFSET(i2c0_scl), (MODE(0) | PULLUP_EN | RXACTIVE | SLEWCTRL)},
|
|
{-1},
|
|
};
|
|
|
|
static struct module_pin_mux gpio5_7_pin_mux[] = {
|
|
{OFFSET(spi0_cs0), (MODE(7) | PULLUP_EN)}, /* GPIO5_7 */
|
|
{-1},
|
|
};
|
|
|
|
void enable_uart0_pin_mux(void)
|
|
{
|
|
configure_module_pin_mux(uart0_pin_mux);
|
|
}
|
|
|
|
void enable_board_pin_mux(void)
|
|
{
|
|
configure_module_pin_mux(mmc0_pin_mux);
|
|
configure_module_pin_mux(i2c0_pin_mux);
|
|
|
|
if (board_is_gpevm())
|
|
configure_module_pin_mux(gpio5_7_pin_mux);
|
|
}
|
|
|
|
void enable_i2c0_pin_mux(void)
|
|
{
|
|
configure_module_pin_mux(i2c0_pin_mux);
|
|
}
|