mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-20 17:08:52 +09:00
![Tom Rini](/assets/img/avatar_default.png)
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
79 lines
1.8 KiB
C
79 lines
1.8 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2005, Psyent Corporation <www.psyent.com>
|
|
* Scott McNutt <smcnutt@psyent.com>
|
|
* (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw>
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* BOARD/CPU
|
|
*/
|
|
|
|
/*
|
|
* SERIAL
|
|
*/
|
|
#define CONFIG_SYS_NS16550_MEM32
|
|
|
|
/*
|
|
* Flash
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 1024
|
|
|
|
/*
|
|
* NET options
|
|
*/
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 0
|
|
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/*
|
|
* FDT options
|
|
*/
|
|
#define CONFIG_LMB
|
|
|
|
/*
|
|
* MEMORY ORGANIZATION
|
|
* -Monitor at top of sdram.
|
|
* -The heap is placed below the monitor
|
|
* -The stack is placed below the heap (&grows down).
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0xc8000000
|
|
#define CONFIG_SYS_SDRAM_SIZE 0x08000000
|
|
#define CONFIG_MONITOR_IS_IN_RAM
|
|
#define CONFIG_SYS_MONITOR_LEN 0x80000 /* Reserve 512k */
|
|
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_SDRAM_BASE + \
|
|
CONFIG_SYS_SDRAM_SIZE - \
|
|
CONFIG_SYS_MONITOR_LEN)
|
|
#define CONFIG_SYS_MALLOC_LEN 0x20000
|
|
|
|
/*
|
|
* ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
|
|
* CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
|
|
* reset address, no? This will keep the environment in user region
|
|
* of flash. NOTE: the monitor length must be multiple of sector size
|
|
* (which is common practice).
|
|
*/
|
|
|
|
#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
|
|
|
|
/*
|
|
* MISC
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0xcc000000 /* Half of RAM */
|
|
#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
|
|
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MONITOR_BASE - \
|
|
CONFIG_ENV_SIZE - \
|
|
CONFIG_SYS_MALLOC_LEN - \
|
|
0x10000)
|
|
|
|
#endif /* __CONFIG_H */
|