mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-22 01:48:52 +09:00
![York Sun](/assets/img/avatar_default.png)
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3 structure for 83xx, 85xx and 86xx. Signed-off-by: York Sun <yorksun@freescale.com>
329 lines
6.6 KiB
C
329 lines
6.6 KiB
C
/*
|
|
* Copyright 2007,2009-2011 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <pci.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/immap_86xx.h>
|
|
#include <asm/fsl_pci.h>
|
|
#include <fsl_ddr_sdram.h>
|
|
#include <asm/fsl_serdes.h>
|
|
#include <i2c.h>
|
|
#include <asm/io.h>
|
|
#include <libfdt.h>
|
|
#include <fdt_support.h>
|
|
#include <spd_sdram.h>
|
|
#include <netdev.h>
|
|
|
|
void sdram_init(void);
|
|
phys_size_t fixed_sdram(void);
|
|
int mpc8610hpcd_diu_init(void);
|
|
|
|
|
|
/* called before any console output */
|
|
int board_early_init_f(void)
|
|
{
|
|
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
|
|
volatile ccsr_gur_t *gur = &immap->im_gur;
|
|
|
|
gur->gpiocr |= 0x88aa5500; /* DIU16, IR1, UART0, UART2 */
|
|
|
|
return 0;
|
|
}
|
|
|
|
int misc_init_r(void)
|
|
{
|
|
u8 tmp_val, version;
|
|
u8 *pixis_base = (u8 *)PIXIS_BASE;
|
|
|
|
/*Do not use 8259PIC*/
|
|
tmp_val = in_8(pixis_base + PIXIS_BRDCFG0);
|
|
out_8(pixis_base + PIXIS_BRDCFG0, tmp_val | 0x80);
|
|
|
|
/*For FPGA V7 or higher, set the IRQMAPSEL to 0 to use MAP0 interrupt*/
|
|
version = in_8(pixis_base + PIXIS_PVER);
|
|
if(version >= 0x07) {
|
|
tmp_val = in_8(pixis_base + PIXIS_BRDCFG0);
|
|
out_8(pixis_base + PIXIS_BRDCFG0, tmp_val & 0xbf);
|
|
}
|
|
|
|
/* Using this for DIU init before the driver in linux takes over
|
|
* Enable the TFP410 Encoder (I2C address 0x38)
|
|
*/
|
|
|
|
tmp_val = 0xBF;
|
|
i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
|
|
/* Verify if enabled */
|
|
tmp_val = 0;
|
|
i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
|
|
debug("DVI Encoder Read: 0x%02x\n", tmp_val);
|
|
|
|
tmp_val = 0x10;
|
|
i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
|
|
/* Verify if enabled */
|
|
tmp_val = 0;
|
|
i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
|
|
debug("DVI Encoder Read: 0x%02x\n", tmp_val);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
|
|
volatile ccsr_local_mcm_t *mcm = &immap->im_local_mcm;
|
|
u8 *pixis_base = (u8 *)PIXIS_BASE;
|
|
|
|
printf ("Board: MPC8610HPCD, Sys ID: 0x%02x, "
|
|
"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
|
|
in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
|
|
in_8(pixis_base + PIXIS_PVER));
|
|
|
|
/*
|
|
* The MPC8610 HPCD workbook says that LBMAP=11 is the "normal" boot
|
|
* bank and LBMAP=00 is the alternate bank. However, the pixis
|
|
* altbank code can only set bits, not clear them, so we treat 00 as
|
|
* the normal bank and 11 as the alternate.
|
|
*/
|
|
switch (in_8(pixis_base + PIXIS_VBOOT) & 0xC0) {
|
|
case 0:
|
|
puts("vBank: Standard\n");
|
|
break;
|
|
case 0x40:
|
|
puts("Promjet\n");
|
|
break;
|
|
case 0x80:
|
|
puts("NAND\n");
|
|
break;
|
|
case 0xC0:
|
|
puts("vBank: Alternate\n");
|
|
break;
|
|
}
|
|
|
|
mcm->abcr |= 0x00010000; /* 0 */
|
|
mcm->hpmr3 = 0x80000008; /* 4c */
|
|
mcm->hpmr0 = 0;
|
|
mcm->hpmr1 = 0;
|
|
mcm->hpmr2 = 0;
|
|
mcm->hpmr4 = 0;
|
|
mcm->hpmr5 = 0;
|
|
|
|
return 0;
|
|
}
|
|
|
|
|
|
phys_size_t
|
|
initdram(int board_type)
|
|
{
|
|
phys_size_t dram_size = 0;
|
|
|
|
#if defined(CONFIG_SPD_EEPROM)
|
|
dram_size = fsl_ddr_sdram();
|
|
#else
|
|
dram_size = fixed_sdram();
|
|
#endif
|
|
|
|
setup_ddr_bat(dram_size);
|
|
|
|
debug(" DDR: ");
|
|
return dram_size;
|
|
}
|
|
|
|
|
|
#if !defined(CONFIG_SPD_EEPROM)
|
|
/*
|
|
* Fixed sdram init -- doesn't use serial presence detect.
|
|
*/
|
|
|
|
phys_size_t fixed_sdram(void)
|
|
{
|
|
#if !defined(CONFIG_SYS_RAMBOOT)
|
|
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
|
|
struct ccsr_ddr __iomem *ddr = &immap->im_ddr1;
|
|
uint d_init;
|
|
|
|
ddr->cs0_bnds = 0x0000001f;
|
|
ddr->cs0_config = 0x80010202;
|
|
|
|
ddr->timing_cfg_3 = 0x00000000;
|
|
ddr->timing_cfg_0 = 0x00260802;
|
|
ddr->timing_cfg_1 = 0x3935d322;
|
|
ddr->timing_cfg_2 = 0x14904cc8;
|
|
ddr->sdram_mode = 0x00480432;
|
|
ddr->sdram_mode_2 = 0x00000000;
|
|
ddr->sdram_interval = 0x06180fff; /* 0x06180100; */
|
|
ddr->sdram_data_init = 0xDEADBEEF;
|
|
ddr->sdram_clk_cntl = 0x03800000;
|
|
ddr->sdram_cfg_2 = 0x04400010;
|
|
|
|
#if defined(CONFIG_DDR_ECC)
|
|
ddr->err_int_en = 0x0000000d;
|
|
ddr->err_disable = 0x00000000;
|
|
ddr->err_sbe = 0x00010000;
|
|
#endif
|
|
asm("sync;isync");
|
|
|
|
udelay(500);
|
|
|
|
ddr->sdram_cfg = 0xc3000000; /* 0xe3008000;*/
|
|
|
|
|
|
#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
|
|
d_init = 1;
|
|
debug("DDR - 1st controller: memory initializing\n");
|
|
/*
|
|
* Poll until memory is initialized.
|
|
* 512 Meg at 400 might hit this 200 times or so.
|
|
*/
|
|
while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0)
|
|
udelay(1000);
|
|
|
|
debug("DDR: memory initialized\n\n");
|
|
asm("sync; isync");
|
|
udelay(500);
|
|
#endif
|
|
|
|
return 512 * 1024 * 1024;
|
|
#endif
|
|
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
|
|
}
|
|
|
|
#endif
|
|
|
|
#if defined(CONFIG_PCI)
|
|
/*
|
|
* Initialize PCI Devices, report devices found.
|
|
*/
|
|
|
|
#ifndef CONFIG_PCI_PNP
|
|
static struct pci_config_table pci_fsl86xxads_config_table[] = {
|
|
{PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
|
|
PCI_IDSEL_NUMBER, PCI_ANY_ID,
|
|
pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
|
|
PCI_ENET0_MEMADDR,
|
|
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER} },
|
|
{}
|
|
};
|
|
#endif
|
|
|
|
|
|
static struct pci_controller pci1_hose;
|
|
#endif /* CONFIG_PCI */
|
|
|
|
void pci_init_board(void)
|
|
{
|
|
volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR;
|
|
volatile ccsr_gur_t *gur = &immap->im_gur;
|
|
struct fsl_pci_info pci_info;
|
|
u32 devdisr;
|
|
int first_free_busno;
|
|
int pci_agent;
|
|
|
|
devdisr = in_be32(&gur->devdisr);
|
|
|
|
first_free_busno = fsl_pcie_init_board(0);
|
|
|
|
#ifdef CONFIG_PCI1
|
|
if (!(devdisr & MPC86xx_DEVDISR_PCI1)) {
|
|
SET_STD_PCI_INFO(pci_info, 1);
|
|
set_next_law(pci_info.mem_phys,
|
|
law_size_bits(pci_info.mem_size), pci_info.law);
|
|
set_next_law(pci_info.io_phys,
|
|
law_size_bits(pci_info.io_size), pci_info.law);
|
|
|
|
pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs);
|
|
printf("PCI: connected to PCI slots as %s" \
|
|
" (base address %lx)\n",
|
|
pci_agent ? "Agent" : "Host",
|
|
pci_info.regs);
|
|
#ifndef CONFIG_PCI_PNP
|
|
pci1_hose.config_table = pci_mpc86xxcts_config_table;
|
|
#endif
|
|
first_free_busno = fsl_pci_init_port(&pci_info,
|
|
&pci1_hose, first_free_busno);
|
|
} else {
|
|
printf("PCI: disabled\n");
|
|
}
|
|
|
|
puts("\n");
|
|
#else
|
|
setbits_be32(&gur->devdisr, MPC86xx_DEVDISR_PCI1); /* disable */
|
|
#endif
|
|
|
|
fsl_pcie_init_board(first_free_busno);
|
|
}
|
|
|
|
#if defined(CONFIG_OF_BOARD_SETUP)
|
|
void
|
|
ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
ft_cpu_setup(blob, bd);
|
|
|
|
FT_FSL_PCI_SETUP;
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* get_board_sys_clk
|
|
* Reads the FPGA on board for CONFIG_SYS_CLK_FREQ
|
|
*/
|
|
|
|
unsigned long
|
|
get_board_sys_clk(ulong dummy)
|
|
{
|
|
u8 i;
|
|
ulong val = 0;
|
|
u8 *pixis_base = (u8 *)PIXIS_BASE;
|
|
|
|
i = in_8(pixis_base + PIXIS_SPD);
|
|
i &= 0x07;
|
|
|
|
switch (i) {
|
|
case 0:
|
|
val = 33333000;
|
|
break;
|
|
case 1:
|
|
val = 39999600;
|
|
break;
|
|
case 2:
|
|
val = 49999500;
|
|
break;
|
|
case 3:
|
|
val = 66666000;
|
|
break;
|
|
case 4:
|
|
val = 83332500;
|
|
break;
|
|
case 5:
|
|
val = 99999000;
|
|
break;
|
|
case 6:
|
|
val = 133332000;
|
|
break;
|
|
case 7:
|
|
val = 166665000;
|
|
break;
|
|
}
|
|
|
|
return val;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
return pci_eth_init(bis);
|
|
}
|
|
|
|
void board_reset(void)
|
|
{
|
|
u8 *pixis_base = (u8 *)PIXIS_BASE;
|
|
|
|
out_8(pixis_base + PIXIS_RST, 0);
|
|
|
|
while (1)
|
|
;
|
|
}
|