mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-15 06:33:45 +09:00
![Bibek Basu](/assets/img/avatar_default.png)
RAM repair has a few pre-requisites: 1) PMIC power supply (rail) enabled. 2) PMC CRAIL power partition powered. 3) Fuse clock active (it's the default). 4) PLLP reshift branch enabled (it's the default, when PLLP is active). RAM repair also only need run whenever specific partitions are powered (main SoC and CCPLEX respectively); RAM repair does not need to be triggered when any other partition changes state. start_cpu() needs to be re-ordered slightly to match these requirements. Note that C0NC and CE0 aren't required for RAM repair to operate, but they also do no harm, so the entire of powerup_cpus() is moved rather than splitting it up. The call to remove_cpu_resets() is moved last to ensure that all other actions complete before releasing reset; since the PMC power partitions are now enabled early, releasing reset is what causes the CPUs to start executing code, and RAM repair must complete before the CPU boots. Note that this commit is the result of squashing a numbmer of commits in NVIDIA's downstream L4T branch, hence the multiple signoffs below. Signed-off-by: Bibek Basu <bbasu@nvidia.com> Signed-off-by: Sandipan Patra <spatra@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
302 lines
8.6 KiB
C
302 lines
8.6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2013
|
|
* NVIDIA Corporation <www.nvidia.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/ahb.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/flow.h>
|
|
#include <asm/arch/pinmux.h>
|
|
#include <asm/arch/tegra.h>
|
|
#include <asm/arch-tegra/clk_rst.h>
|
|
#include <asm/arch-tegra/pmc.h>
|
|
#include <asm/arch-tegra/ap.h>
|
|
#include "../cpu.h"
|
|
|
|
/* Tegra124-specific CPU init code */
|
|
|
|
static void enable_cpu_power_rail(void)
|
|
{
|
|
struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
|
|
|
|
debug("%s entry\n", __func__);
|
|
|
|
/* un-tristate PWR_I2C SCL/SDA, rest of the defaults are correct */
|
|
pinmux_tristate_disable(PMUX_PINGRP_PWR_I2C_SCL_PZ6);
|
|
pinmux_tristate_disable(PMUX_PINGRP_PWR_I2C_SDA_PZ7);
|
|
|
|
pmic_enable_cpu_vdd();
|
|
|
|
/*
|
|
* Set CPUPWRGOOD_TIMER - APB clock is 1/2 of SCLK (102MHz),
|
|
* set it for 5ms as per SysEng (102MHz*5ms = 510000 (7C830h).
|
|
*/
|
|
writel(0x7C830, &pmc->pmc_cpupwrgood_timer);
|
|
|
|
/* Set polarity to 0 (normal) and enable CPUPWRREQ_OE */
|
|
clrbits_le32(&pmc->pmc_cntrl, CPUPWRREQ_POL);
|
|
setbits_le32(&pmc->pmc_cntrl, CPUPWRREQ_OE);
|
|
}
|
|
|
|
static void enable_cpu_clocks(void)
|
|
{
|
|
struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
|
|
struct clk_pll_info *pllinfo = &tegra_pll_info_table[CLOCK_ID_XCPU];
|
|
u32 reg;
|
|
|
|
debug("%s entry\n", __func__);
|
|
|
|
/* Wait for PLL-X to lock */
|
|
do {
|
|
reg = readl(&clkrst->crc_pll_simple[SIMPLE_PLLX].pll_base);
|
|
debug("%s: PLLX base = 0x%08X\n", __func__, reg);
|
|
} while ((reg & (1 << pllinfo->lock_det)) == 0);
|
|
|
|
debug("%s: PLLX locked, delay for stable clocks\n", __func__);
|
|
/* Wait until all clocks are stable */
|
|
udelay(PLL_STABILIZATION_DELAY);
|
|
|
|
debug("%s: Setting CCLK_BURST and DIVIDER\n", __func__);
|
|
writel(CCLK_BURST_POLICY, &clkrst->crc_cclk_brst_pol);
|
|
writel(SUPER_CCLK_DIVIDER, &clkrst->crc_super_cclk_div);
|
|
|
|
debug("%s: Enabling clock to all CPUs\n", __func__);
|
|
/* Enable the clock to all CPUs */
|
|
reg = CLR_CPU3_CLK_STP | CLR_CPU2_CLK_STP | CLR_CPU1_CLK_STP |
|
|
CLR_CPU0_CLK_STP;
|
|
writel(reg, &clkrst->crc_clk_cpu_cmplx_clr);
|
|
|
|
debug("%s: Enabling main CPU complex clocks\n", __func__);
|
|
/* Always enable the main CPU complex clocks */
|
|
clock_enable(PERIPH_ID_CPU);
|
|
clock_enable(PERIPH_ID_CPULP);
|
|
clock_enable(PERIPH_ID_CPUG);
|
|
|
|
debug("%s: Done\n", __func__);
|
|
}
|
|
|
|
static void remove_cpu_resets(void)
|
|
{
|
|
struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
|
|
u32 reg;
|
|
|
|
debug("%s entry\n", __func__);
|
|
|
|
/* Take the slow and fast partitions out of reset */
|
|
reg = CLR_NONCPURESET;
|
|
writel(reg, &clkrst->crc_rst_cpulp_cmplx_clr);
|
|
writel(reg, &clkrst->crc_rst_cpug_cmplx_clr);
|
|
|
|
/* Clear the SW-controlled reset of the slow cluster */
|
|
reg = CLR_CPURESET0 | CLR_DBGRESET0 | CLR_CORERESET0 | CLR_CXRESET0 |
|
|
CLR_L2RESET | CLR_PRESETDBG;
|
|
writel(reg, &clkrst->crc_rst_cpulp_cmplx_clr);
|
|
|
|
/* Clear the SW-controlled reset of the fast cluster */
|
|
reg = CLR_CPURESET0 | CLR_DBGRESET0 | CLR_CORERESET0 | CLR_CXRESET0 |
|
|
CLR_CPURESET1 | CLR_DBGRESET1 | CLR_CORERESET1 | CLR_CXRESET1 |
|
|
CLR_CPURESET2 | CLR_DBGRESET2 | CLR_CORERESET2 | CLR_CXRESET2 |
|
|
CLR_CPURESET3 | CLR_DBGRESET3 | CLR_CORERESET3 | CLR_CXRESET3 |
|
|
CLR_L2RESET | CLR_PRESETDBG;
|
|
writel(reg, &clkrst->crc_rst_cpug_cmplx_clr);
|
|
}
|
|
|
|
static void tegra124_ram_repair(void)
|
|
{
|
|
struct flow_ctlr *flow = (struct flow_ctlr *)NV_PA_FLOW_BASE;
|
|
u32 ram_repair_timeout; /*usec*/
|
|
u32 val;
|
|
|
|
/*
|
|
* Request the Flow Controller perform RAM repair whenever it turns on
|
|
* a power rail that requires RAM repair.
|
|
*/
|
|
clrbits_le32(&flow->ram_repair, RAM_REPAIR_BYPASS_EN);
|
|
|
|
/* Request SW trigerred RAM repair by setting req bit */
|
|
/* cluster 0 */
|
|
setbits_le32(&flow->ram_repair, RAM_REPAIR_REQ);
|
|
/* Wait for completion (status == 0) */
|
|
ram_repair_timeout = 500;
|
|
do {
|
|
udelay(1);
|
|
val = readl(&flow->ram_repair);
|
|
} while (!(val & RAM_REPAIR_STS) && ram_repair_timeout--);
|
|
if (!ram_repair_timeout)
|
|
debug("Ram Repair cluster0 failed\n");
|
|
|
|
/* cluster 1 */
|
|
setbits_le32(&flow->ram_repair_cluster1, RAM_REPAIR_REQ);
|
|
/* Wait for completion (status == 0) */
|
|
ram_repair_timeout = 500;
|
|
do {
|
|
udelay(1);
|
|
val = readl(&flow->ram_repair_cluster1);
|
|
} while (!(val & RAM_REPAIR_STS) && ram_repair_timeout--);
|
|
|
|
if (!ram_repair_timeout)
|
|
debug("Ram Repair cluster1 failed\n");
|
|
}
|
|
|
|
/**
|
|
* Tegra124 requires some special clock initialization, including setting up
|
|
* the DVC I2C, turning on MSELECT and selecting the G CPU cluster
|
|
*/
|
|
void tegra124_init_clocks(void)
|
|
{
|
|
struct flow_ctlr *flow = (struct flow_ctlr *)NV_PA_FLOW_BASE;
|
|
struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
|
|
struct clk_rst_ctlr *clkrst =
|
|
(struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
|
|
u32 val;
|
|
|
|
debug("%s entry\n", __func__);
|
|
|
|
/* Set active CPU cluster to G */
|
|
clrbits_le32(&flow->cluster_control, 1);
|
|
|
|
/* Change the oscillator drive strength */
|
|
val = readl(&clkrst->crc_osc_ctrl);
|
|
val &= ~OSC_XOFS_MASK;
|
|
val |= (OSC_DRIVE_STRENGTH << OSC_XOFS_SHIFT);
|
|
writel(val, &clkrst->crc_osc_ctrl);
|
|
|
|
/* Update same value in PMC_OSC_EDPD_OVER XOFS field for warmboot */
|
|
val = readl(&pmc->pmc_osc_edpd_over);
|
|
val &= ~PMC_XOFS_MASK;
|
|
val |= (OSC_DRIVE_STRENGTH << PMC_XOFS_SHIFT);
|
|
writel(val, &pmc->pmc_osc_edpd_over);
|
|
|
|
/* Set HOLD_CKE_LOW_EN to 1 */
|
|
setbits_le32(&pmc->pmc_cntrl2, HOLD_CKE_LOW_EN);
|
|
|
|
debug("Setting up PLLX\n");
|
|
init_pllx();
|
|
|
|
val = (1 << CLK_SYS_RATE_AHB_RATE_SHIFT);
|
|
writel(val, &clkrst->crc_clk_sys_rate);
|
|
|
|
/* Enable clocks to required peripherals. TBD - minimize this list */
|
|
debug("Enabling clocks\n");
|
|
|
|
clock_set_enable(PERIPH_ID_CACHE2, 1);
|
|
clock_set_enable(PERIPH_ID_GPIO, 1);
|
|
clock_set_enable(PERIPH_ID_TMR, 1);
|
|
clock_set_enable(PERIPH_ID_CPU, 1);
|
|
clock_set_enable(PERIPH_ID_EMC, 1);
|
|
clock_set_enable(PERIPH_ID_I2C5, 1);
|
|
clock_set_enable(PERIPH_ID_APBDMA, 1);
|
|
clock_set_enable(PERIPH_ID_MEM, 1);
|
|
clock_set_enable(PERIPH_ID_CORESIGHT, 1);
|
|
clock_set_enable(PERIPH_ID_MSELECT, 1);
|
|
clock_set_enable(PERIPH_ID_DVFS, 1);
|
|
|
|
/*
|
|
* Set MSELECT clock source as PLLP (00), and ask for a clock
|
|
* divider that would set the MSELECT clock at 102MHz for a
|
|
* PLLP base of 408MHz.
|
|
*/
|
|
clock_ll_set_source_divisor(PERIPH_ID_MSELECT, 0,
|
|
CLK_DIVIDER(NVBL_PLLP_KHZ, 102000));
|
|
|
|
/* Give clock time to stabilize */
|
|
udelay(IO_STABILIZATION_DELAY);
|
|
|
|
/* I2C5 (DVC) gets CLK_M and a divisor of 17 */
|
|
clock_ll_set_source_divisor(PERIPH_ID_I2C5, 3, 16);
|
|
|
|
/* Give clock time to stabilize */
|
|
udelay(IO_STABILIZATION_DELAY);
|
|
|
|
/* Take required peripherals out of reset */
|
|
debug("Taking periphs out of reset\n");
|
|
reset_set_enable(PERIPH_ID_CACHE2, 0);
|
|
reset_set_enable(PERIPH_ID_GPIO, 0);
|
|
reset_set_enable(PERIPH_ID_TMR, 0);
|
|
reset_set_enable(PERIPH_ID_COP, 0);
|
|
reset_set_enable(PERIPH_ID_EMC, 0);
|
|
reset_set_enable(PERIPH_ID_I2C5, 0);
|
|
reset_set_enable(PERIPH_ID_APBDMA, 0);
|
|
reset_set_enable(PERIPH_ID_MEM, 0);
|
|
reset_set_enable(PERIPH_ID_CORESIGHT, 0);
|
|
reset_set_enable(PERIPH_ID_MSELECT, 0);
|
|
reset_set_enable(PERIPH_ID_DVFS, 0);
|
|
|
|
debug("%s exit\n", __func__);
|
|
}
|
|
|
|
static bool is_partition_powered(u32 partid)
|
|
{
|
|
struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
|
|
u32 reg;
|
|
|
|
/* Get power gate status */
|
|
reg = readl(&pmc->pmc_pwrgate_status);
|
|
return !!(reg & (1 << partid));
|
|
}
|
|
|
|
static void power_partition(u32 partid)
|
|
{
|
|
struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
|
|
|
|
debug("%s: part ID = %08X\n", __func__, partid);
|
|
/* Is the partition already on? */
|
|
if (!is_partition_powered(partid)) {
|
|
/* No, toggle the partition power state (OFF -> ON) */
|
|
debug("power_partition, toggling state\n");
|
|
writel(START_CP | partid, &pmc->pmc_pwrgate_toggle);
|
|
|
|
/* Wait for the power to come up */
|
|
while (!is_partition_powered(partid))
|
|
;
|
|
|
|
/* Give I/O signals time to stabilize */
|
|
udelay(IO_STABILIZATION_DELAY);
|
|
}
|
|
}
|
|
|
|
void powerup_cpus(void)
|
|
{
|
|
/* We boot to the fast cluster */
|
|
debug("%s entry: G cluster\n", __func__);
|
|
|
|
/* Power up the fast cluster rail partition */
|
|
debug("%s: CRAIL\n", __func__);
|
|
power_partition(CRAIL);
|
|
|
|
/* Power up the fast cluster non-CPU partition */
|
|
debug("%s: C0NC\n", __func__);
|
|
power_partition(C0NC);
|
|
|
|
/* Power up the fast cluster CPU0 partition */
|
|
debug("%s: CE0\n", __func__);
|
|
power_partition(CE0);
|
|
|
|
debug("%s: done\n", __func__);
|
|
}
|
|
|
|
void start_cpu(u32 reset_vector)
|
|
{
|
|
struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
|
|
|
|
debug("%s entry, reset_vector = %x\n", __func__, reset_vector);
|
|
|
|
tegra124_init_clocks();
|
|
|
|
/* Set power-gating timer multiplier */
|
|
writel((MULT_8 << TIMER_MULT_SHIFT) | (MULT_8 << TIMER_MULT_CPU_SHIFT),
|
|
&pmc->pmc_pwrgate_timer_mult);
|
|
|
|
enable_cpu_power_rail();
|
|
powerup_cpus();
|
|
tegra124_ram_repair();
|
|
enable_cpu_clocks();
|
|
clock_enable_coresight(1);
|
|
writel(reset_vector, EXCEP_VECTOR_CPU_RESET_VECTOR);
|
|
remove_cpu_resets();
|
|
debug("%s exit, should continue @ reset_vector\n", __func__);
|
|
}
|