mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-07-12 06:06:15 +09:00
2be296538e
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
136 lines
3.6 KiB
C
136 lines
3.6 KiB
C
/*
|
|
* Copyright (C) 2013 Marek Vasut <marex@denx.de>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
#ifndef __CONFIGS_MX23_OLINUXINO_H__
|
|
#define __CONFIGS_MX23_OLINUXINO_H__
|
|
|
|
/* System configurations */
|
|
#define CONFIG_MX23 /* i.MX23 SoC */
|
|
#define CONFIG_MACH_TYPE 4105
|
|
|
|
/* U-Boot Commands */
|
|
|
|
/* Memory configuration */
|
|
#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
|
|
#define PHYS_SDRAM_1 0x40000000 /* Base address */
|
|
#define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
|
|
/* Environment */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
/* Environment is in MMC */
|
|
#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC)
|
|
#define CONFIG_ENV_OFFSET (256 * 1024)
|
|
#define CONFIG_ENV_SIZE (16 * 1024)
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
#endif
|
|
|
|
/* Status LED */
|
|
|
|
/* USB */
|
|
#ifdef CONFIG_CMD_USB
|
|
#define CONFIG_EHCI_MXS_PORT0
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
|
|
#endif
|
|
|
|
/* Ethernet */
|
|
#ifdef CONFIG_CMD_NET
|
|
#define CONFIG_USB_HOST_ETHER
|
|
#define CONFIG_USB_ETHER_SMSC95XX
|
|
#endif
|
|
|
|
/* Booting Linux */
|
|
#define CONFIG_BOOTFILE "uImage"
|
|
#define CONFIG_LOADADDR 0x42000000
|
|
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
|
|
|
|
/* Extra Environment */
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"update_sd_firmware_filename=u-boot.sd\0" \
|
|
"update_sd_firmware=" /* Update the SD firmware partition */ \
|
|
"if mmc rescan ; then " \
|
|
"if tftp ${update_sd_firmware_filename} ; then " \
|
|
"setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \
|
|
"setexpr fw_sz ${fw_sz} + 1 ; " \
|
|
"mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
|
|
"fi ; " \
|
|
"fi\0" \
|
|
"script=boot.scr\0" \
|
|
"uimage=uImage\0" \
|
|
"console=ttyAMA0\0" \
|
|
"fdt_file=imx23-olinuxino.dtb\0" \
|
|
"fdt_addr=0x41000000\0" \
|
|
"boot_fdt=try\0" \
|
|
"ip_dyn=yes\0" \
|
|
"mmcdev=0\0" \
|
|
"mmcpart=2\0" \
|
|
"mmcroot=/dev/mmcblk0p3 rw rootwait\0" \
|
|
"mmcargs=setenv bootargs console=${console},${baudrate} " \
|
|
"root=${mmcroot}\0" \
|
|
"loadbootscript=" \
|
|
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
|
|
"bootscript=echo Running bootscript from mmc ...; " \
|
|
"source\0" \
|
|
"loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
|
|
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
|
|
"mmcboot=echo Booting from mmc ...; " \
|
|
"run mmcargs; " \
|
|
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
|
|
"if run loadfdt; then " \
|
|
"bootm ${loadaddr} - ${fdt_addr}; " \
|
|
"else " \
|
|
"if test ${boot_fdt} = try; then " \
|
|
"bootm; " \
|
|
"else " \
|
|
"echo WARN: Cannot load the DT; " \
|
|
"fi; " \
|
|
"fi; " \
|
|
"else " \
|
|
"bootm; " \
|
|
"fi;\0" \
|
|
"netargs=setenv bootargs console=${console},${baudrate} " \
|
|
"root=/dev/nfs " \
|
|
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
|
|
"netboot=echo Booting from net ...; " \
|
|
"usb start; " \
|
|
"run netargs; " \
|
|
"if test ${ip_dyn} = yes; then " \
|
|
"setenv get_cmd dhcp; " \
|
|
"else " \
|
|
"setenv get_cmd tftp; " \
|
|
"fi; " \
|
|
"${get_cmd} ${uimage}; " \
|
|
"if test ${boot_fdt} = yes; then " \
|
|
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
|
|
"bootm ${loadaddr} - ${fdt_addr}; " \
|
|
"else " \
|
|
"if test ${boot_fdt} = try; then " \
|
|
"bootm; " \
|
|
"else " \
|
|
"echo WARN: Cannot load the DT; " \
|
|
"fi;" \
|
|
"fi; " \
|
|
"else " \
|
|
"bootm; " \
|
|
"fi;\0"
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"mmc dev ${mmcdev}; if mmc rescan; then " \
|
|
"if run loadbootscript; then " \
|
|
"run bootscript; " \
|
|
"else " \
|
|
"if run loaduimage; then " \
|
|
"run mmcboot; " \
|
|
"else run netboot; " \
|
|
"fi; " \
|
|
"fi; " \
|
|
"else run netboot; fi"
|
|
|
|
/* The rest of the configuration is shared */
|
|
#include <configs/mxs.h>
|
|
|
|
#endif /* __CONFIGS_MX23_OLINUXINO_H__ */
|