mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-22 01:48:52 +09:00
![Stephen Arnold](/assets/img/avatar_default.png)
This patch adds the steps to manually (re)build a Quartus FPGA project, generate the required BSP glue, and update u-boot handoff files for mainline SPL support. Requires Quartus toolchain and current U-Boot. Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de>
150 lines
5.2 KiB
Plaintext
150 lines
5.2 KiB
Plaintext
----------------------------------------
|
|
SOCFPGA Documentation for U-Boot and SPL
|
|
----------------------------------------
|
|
|
|
This README is about U-Boot and SPL support for Altera's ARM Cortex-A9MPCore
|
|
based SOCFPGA. To know more about the hardware itself, please refer to
|
|
www.altera.com.
|
|
|
|
|
|
socfpga_dw_mmc
|
|
--------------
|
|
|
|
Here are macro and detailed configuration required to enable DesignWare SDMMC
|
|
controller support within SOCFPGA
|
|
|
|
#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256
|
|
-> Using smaller max blk cnt to avoid flooding the limited stack in OCRAM
|
|
|
|
--------------------------------------------------
|
|
Generating the handoff header files for U-Boot SPL
|
|
--------------------------------------------------
|
|
|
|
This text is assuming quartus 16.1, but newer versions will probably work just fine too;
|
|
verified with DE1_SOC_Linux_FB demo project (https://github.com/VCTLabs/DE1_SOC_Linux_FB).
|
|
Updated/working projects should build using either process below.
|
|
|
|
Note: it *should* work from Quartus 14.0.200 onwards, however, the current vendor demo
|
|
projects must have the IP cores updated as shown below.
|
|
|
|
Rebuilding your Quartus project
|
|
-------------------------------
|
|
|
|
Choose one of the follwing methods, either command line or GUI.
|
|
|
|
Using the comaand line
|
|
~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
First run the embedded command shell, using your path to the Quartus install:
|
|
|
|
$ /path/to/intelFPGA/16.1/embedded/embedded_command_shell.sh
|
|
|
|
Then (if necessary) update the IP cores in the project, generate HDL code, and
|
|
build the project:
|
|
|
|
$ cd path/to/project/dir
|
|
$ qsys-generate soc_system.qsys --upgrade-ip-cores
|
|
$ qsys-generate soc_system.qsys --synthesis=[VERILOG|VHDL]
|
|
$ quartus_sh --flow compile <project name>
|
|
|
|
Convert the resulting .sof file (SRAM object file) to .rbf file (Raw bit file):
|
|
|
|
$ quartus_cpf -c <project_name>.sof soc_system.rbf
|
|
|
|
|
|
Generate BSP handoff files
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
You can run the bsp editor GUI below, or run the following command from the
|
|
project directory:
|
|
|
|
$ /path/to/bsb/tools/bsp-create-settings --type spl --bsp-dir build \
|
|
--preloader-settings-dir hps_isw_handoff/soc_system_hps_0/ \
|
|
--settings build/settings.bsp
|
|
|
|
You should use the bsp "build" directory above (ie, where the settings.bsp file is)
|
|
in the following u-boot command to update the board headers. Once these headers
|
|
are updated for a given project build, u-boot should be configured for the
|
|
project board (eg, de0-nano-sockit) and then build the normal spl build.
|
|
|
|
Now you can skip the GUI section.
|
|
|
|
|
|
Using the Qsys GUI
|
|
~~~~~~~~~~~~~~~~~~
|
|
|
|
1. Navigate to your project directory
|
|
2. Run Quartus II
|
|
3. Open Project (Ctrl+J), select <project_name>.qpf
|
|
4. Run QSys [Tools->QSys]
|
|
4.1 In the Open dialog, select '<project_name>.qsys'
|
|
4.2 In the Open System dialog, wait until completion and press 'Close'
|
|
4.3 In the Qsys window, click on 'Generate HDL...' in bottom right corner
|
|
4.3.1 In the 'Generation' window, click 'Generate'
|
|
4.3.2 In the 'Generate' dialog, wait until completion and click 'Close'
|
|
4.4 In the QSys window, click 'Finish'
|
|
4.4.1 In the 'Quartus II' pop up window, click 'OK'
|
|
5. Back in Quartus II main window, do the following
|
|
5.1 Use Processing -> Start -> Start Analysis & Synthesis (Ctrl+K)
|
|
5.2 Use Processing -> Start Compilation (Ctrl+L)
|
|
|
|
... this may take some time, have patience ...
|
|
|
|
6. Start the embedded command shell as shown in the previous section
|
|
6.1 Change directory to 'software/spl_bsp'
|
|
6.2 Prepare BSP by launching the BSP editor from ECS
|
|
=> bsp-editor
|
|
6.3 In BSP editor
|
|
6.3.1 Use File -> Open
|
|
6.3.2 Select 'settings.bsp' file
|
|
6.3.3 Click Generate
|
|
6.3.4 Click Exit
|
|
|
|
|
|
Post handoff generation
|
|
~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
Now that the handoff files are generated, U-Boot can be used to process
|
|
the handoff files generated by the bsp-editor. For this, please use the
|
|
following script from the u-boot source tree:
|
|
|
|
$ ./arch/arm/mach-socfpga/qts-filter.sh \
|
|
<soc_type> \
|
|
<input_qts_dir> \
|
|
<input_bsp_dir> \
|
|
<output_dir>
|
|
|
|
Process QTS-generated files into U-Boot compatible ones.
|
|
|
|
soc_type - Type of SoC, either 'cyclone5' or 'arria5'.
|
|
input_qts_dir - Directory with compiled Quartus project
|
|
and containing the Quartus project file (QPF).
|
|
input_bsp_dir - Directory with generated bsp containing
|
|
the settings.bsp file.
|
|
output_dir - Directory to store the U-Boot compatible
|
|
headers.
|
|
|
|
This will generate (or update) the following 4 files:
|
|
|
|
iocsr_config.h
|
|
pinmux_config.h
|
|
pll_config.h
|
|
sdram_config.h
|
|
|
|
These files should be copied into "qts" directory in the board directory
|
|
(see output argument of qts-filter.sh command above).
|
|
|
|
Here is an example for the DE-0 Nano SoC after the above rebuild process:
|
|
|
|
$ ll board/terasic/de0-nano-soc/qts/
|
|
total 36
|
|
-rw-r--r-- 1 sarnold sarnold 8826 Mar 21 18:11 iocsr_config.h
|
|
-rw-r--r-- 1 sarnold sarnold 4398 Mar 21 18:11 pinmux_config.h
|
|
-rw-r--r-- 1 sarnold sarnold 3190 Mar 21 18:11 pll_config.h
|
|
-rw-r--r-- 1 sarnold sarnold 9022 Mar 21 18:11 sdram_config.h
|
|
|
|
Note: file sizes will differ slightly depending on the selected board.
|
|
|
|
Now your board is ready for full mainline support including U-Boot SPL.
|
|
The Preloader will not be needed any more.
|