mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-20 17:08:52 +09:00
![Tom Rini](/assets/img/avatar_default.png)
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
72 lines
2.4 KiB
C
72 lines
2.4 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Configuation settings for the Renesas SH7763RDP board
|
|
*
|
|
* Copyright (C) 2008 Renesas Solutions Corp.
|
|
* Copyright (C) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
|
|
*/
|
|
|
|
#ifndef __SH7763RDP_H
|
|
#define __SH7763RDP_H
|
|
|
|
#define CONFIG_CPU_SH7763 1
|
|
#define __LITTLE_ENDIAN 1
|
|
|
|
#define CONFIG_ENV_OVERWRITE 1
|
|
|
|
#define CONFIG_DISPLAY_BOARDINFO
|
|
|
|
/* SCIF */
|
|
#define CONFIG_CONS_SCIF2 1
|
|
|
|
#define CONFIG_SYS_PBSIZE 256 /* Buffer size for Console output */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 115200 } /* List of legal baudrate
|
|
settings for this board */
|
|
|
|
/* SDRAM */
|
|
#define CONFIG_SYS_SDRAM_BASE (0x8C000000)
|
|
#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024)
|
|
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE)
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024))
|
|
|
|
/* Flash(NOR) */
|
|
#define CONFIG_SYS_FLASH_BASE (0xA0000000)
|
|
#define CONFIG_SYS_FLASH_CFI_WIDTH (FLASH_CFI_16BIT)
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS (1)
|
|
#define CONFIG_SYS_MAX_FLASH_SECT (520)
|
|
|
|
/* U-Boot setting */
|
|
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 4 * 1024 * 1024)
|
|
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE)
|
|
#define CONFIG_SYS_MONITOR_LEN (128 * 1024)
|
|
/* Size of DRAM reserved for malloc() use */
|
|
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
|
|
|
|
#undef CONFIG_SYS_FLASH_QUIET_TEST
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
|
|
/* Timeout for Flash erase operations (in ms) */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000)
|
|
/* Timeout for Flash write operations (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000)
|
|
/* Timeout for Flash set sector lock bit operations (in ms) */
|
|
#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000)
|
|
/* Timeout for Flash clear lock bit operations (in ms) */
|
|
#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000)
|
|
/* Use hardware flash sectors protection instead of U-Boot software protection */
|
|
#undef CONFIG_SYS_DIRECT_FLASH_TFTP
|
|
/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */
|
|
|
|
/* Clock */
|
|
#define CONFIG_SYS_CLK_FREQ 66666666
|
|
#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ
|
|
|
|
/* Ether */
|
|
#define CONFIG_SH_ETHER_USE_PORT (1)
|
|
#define CONFIG_SH_ETHER_PHY_ADDR (0x01)
|
|
#define CONFIG_BITBANGMII
|
|
#define CONFIG_BITBANGMII_MULTI
|
|
#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_MII
|
|
|
|
#endif /* __SH7763RDP_H */
|