mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-23 10:28:51 +09:00
![]() This problem is seen on Zoom1 and Zoom2 in the startup and when i2c probe is used Before : In: serial Out: serial Err: serial timed out in wait_for_bb: I2C_STAT=1000 timed out in wait_for_bb: I2C_STAT=1000 timed out in wait_for_bb: I2C_STAT=1000 timed out in wait_for_pin: I2C_STAT=1000 I2C read: I/O error timed out in wait_for_bb: I2C_STAT=1000 timed out in wait_for_bb: I2C_STAT=1000 Die ID #327c00020000000004013ddd05026013 Hit any key to stop autoboot: 0 OMAP3 Zoom1# i2c probe Valid chip addresses:timed out in wait_for_bb: I2C_STAT=1000 02 03 04 05 06 07 08 09 0A 0B 0C 0D <snip> After : In: serial Out: serial Err: serial Die ID #327c00020000000004013ddd05026013 Hit any key to stop autoboot: 0 OMAP3 Zoom1# i2c probe Valid chip addresses: 48 49 4A 4B The addresses are for the twl4030. The prescalar that converts the function clock to the sampling clock is hardcoded to 0. The reference manual recommends 7 if the function clock is 96MHz. Instead of just changing the hardcoded values, the prescalar is calculated from the value I2C_IP_CLK. The i2c #defines are in kHz. The speed passed into the i2c init routine is in Hz. To be consistent, change the defines to be in Hz. The timing calculations are based on what is done in the linux 2.6.30 kernel in drivers/i2c/buses/i2c_omap.c as apposed to what is done in TRM. The major variables in the timing caculations are specified as #defines that can be overriden as required. The variables and their defaults are I2C_IP_CLK SYSTEM_CLOCK_96 I2C_INTERNAL_SAMPLING_CLK 19200000 I2C_FASTSPEED_SCLL_TRIM 6 I2C_FASTSPEED_SCLH_TRIM 6 I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM I2C_HIGHSPEED_PHASE_TWO_SCLH I2C_FASTSPEED_SCLH_TRIM This was runtime verified on Zoom1, Zoom2, Beagle and Overo. The 400kHz and 3.4M cases were verifed on test Zoom1, Zoom2, Beagle and Overo configurations. Testing for omap2 will be done in a second step as Nishanth and Jean-Christophe commented. Signed-off-by: Tom Rix <Tom.Rix@windriver.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Heiko Schocher <hs@denx.de> |
||
---|---|---|
.. | ||
bits.h | ||
clocks.h | ||
i2c.h | ||
mem.h | ||
mux.h | ||
omap2420.h | ||
sizes.h | ||
sys_info.h | ||
sys_proto.h |