mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-20 08:58:52 +09:00
![wdenk](/assets/img/avatar_default.png)
- remove trailing white space, trailing empty lines, C++ comments, etc. - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c) * Patches by Kenneth Johansson, 25 Jun 2003: - major rework of command structure (work done mostly by Michal Cendrowski and Joakim Kristiansen)
176 lines
6.9 KiB
Plaintext
176 lines
6.9 KiB
Plaintext
NAND FLASH commands and notes
|
|
|
|
# (C) Copyright 2003
|
|
# Dave Ellis, SIXNET, dge@sixnetio.com
|
|
#
|
|
# See file CREDITS for list of people who contributed to this
|
|
# project.
|
|
#
|
|
# This program is free software; you can redistribute it and/or
|
|
# modify it under the terms of the GNU General Public License as
|
|
# published by the Free Software Foundation; either version 2 of
|
|
# the License, or (at your option) any later version.
|
|
#
|
|
# This program is distributed in the hope that it will be useful,
|
|
# but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
# GNU General Public License for more details.
|
|
#
|
|
# You should have received a copy of the GNU General Public License
|
|
# along with this program; if not, write to the Free Software
|
|
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
# MA 02111-1307 USA
|
|
|
|
Commands:
|
|
|
|
nand bad
|
|
Print a list of all of the bad blocks in the current device.
|
|
|
|
nand device
|
|
Print information about the current NAND device.
|
|
|
|
nand device num
|
|
Make device `num' the current device and print information about it.
|
|
|
|
nand erase off size
|
|
nand erase clean [off size]
|
|
Erase `size' bytes starting at offset `off'. Only complete erase
|
|
blocks can be erased.
|
|
|
|
If `clean' is specified, a JFFS2-style clean marker is written to
|
|
each block after it is erased. If `clean' is specified without an
|
|
offset or size, the entire flash is erased.
|
|
|
|
This command will not erase blocks that are marked bad. There is
|
|
a debug option in cmd_nand.c to allow bad blocks to be erased.
|
|
Please read the warning there before using it, as blocks marked
|
|
bad by the manufacturer must _NEVER_ be erased.
|
|
|
|
nand info
|
|
Print information about all of the NAND devices found.
|
|
|
|
nand read addr ofs size
|
|
Read `size' bytes from `ofs' in NAND flash to `addr'. If a page
|
|
cannot be read because it is marked bad or an uncorrectable data
|
|
error is found the command stops with an error.
|
|
|
|
nand read.jffs2 addr ofs size
|
|
Like `read', but the data for blocks that are marked bad is read as
|
|
0xff. This gives a readable JFFS2 image that can be processed by
|
|
the JFFS2 commands such as ls and fsload.
|
|
|
|
nand read.oob addr ofs size
|
|
Read `size' bytes from the out-of-band data area corresponding to
|
|
`ofs' in NAND flash to `addr'. This is limited to the 16 bytes of
|
|
data for one 512-byte page or 2 256-byte pages. There is no check
|
|
for bad blocks or ECC errors.
|
|
|
|
nand write addr ofs size
|
|
Write `size' bytes from `addr' to `ofs' in NAND flash. If a page
|
|
cannot be written because it is marked bad or the write fails the
|
|
command stops with an error.
|
|
|
|
nand write.jffs2 addr ofs size
|
|
Like `write', but blocks that are marked bad are skipped and the
|
|
is written to the next block instead. This allows writing writing
|
|
a JFFS2 image, as long as the image is short enough to fit even
|
|
after skipping the bad blocks. Compact images, such as those
|
|
produced by mkfs.jffs2 should work well, but loading an image copied
|
|
from another flash is going to be trouble if there are any bad blocks.
|
|
|
|
nand write.oob addr ofs size
|
|
Write `size' bytes from `addr' to the out-of-band data area
|
|
corresponding to `ofs' in NAND flash. This is limited to the 16 bytes
|
|
of data for one 512-byte page or 2 256-byte pages. There is no check
|
|
for bad blocks.
|
|
|
|
Configuration Options:
|
|
|
|
CFG_CMD_NAND
|
|
A good one to add to CONFIG_COMMANDS since it enables NAND support.
|
|
|
|
CONFIG_MTD_NAND_ECC_JFFS2
|
|
Define this if you want the Error Correction Code information in
|
|
the out-of-band data to be formatted to match the JFFS2 file system.
|
|
CONFIG_MTD_NAND_ECC_YAFFS would be another useful choice for
|
|
someone to implement.
|
|
|
|
CFG_MAX_NAND_DEVICE
|
|
The maximum number of NAND devices you want to support.
|
|
|
|
NAND Interface:
|
|
|
|
#define NAND_WAIT_READY(nand)
|
|
Wait until the NAND flash is ready. Typically this would be a
|
|
loop waiting for the READY/BUSY line from the flash to indicate it
|
|
it is ready.
|
|
|
|
#define WRITE_NAND_COMMAND(d, adr)
|
|
Write the command byte `d' to the flash at `adr' with the
|
|
CLE (command latch enable) line true. If your board uses writes to
|
|
different addresses to control CLE and ALE, you can modify `adr'
|
|
to be the appropriate address here. If your board uses I/O registers
|
|
to control them, it is probably better to let NAND_CTL_SETCLE()
|
|
and company do it.
|
|
|
|
#define WRITE_NAND_ADDRESS(d, adr)
|
|
Write the address byte `d' to the flash at `adr' with the
|
|
ALE (address latch enable) line true. If your board uses writes to
|
|
different addresses to control CLE and ALE, you can modify `adr'
|
|
to be the appropriate address here. If your board uses I/O registers
|
|
to control them, it is probably better to let NAND_CTL_SETALE()
|
|
and company do it.
|
|
|
|
#define WRITE_NAND(d, adr)
|
|
Write the data byte `d' to the flash at `adr' with the
|
|
ALE and CLE lines false. If your board uses writes to
|
|
different addresses to control CLE and ALE, you can modify `adr'
|
|
to be the appropriate address here. If your board uses I/O registers
|
|
to control them, it is probably better to let NAND_CTL_CLRALE()
|
|
and company do it.
|
|
|
|
#define READ_NAND(adr)
|
|
Read a data byte from the flash at `adr' with the
|
|
ALE and CLE lines false. If your board uses reads from
|
|
different addresses to control CLE and ALE, you can modify `adr'
|
|
to be the appropriate address here. If your board uses I/O registers
|
|
to control them, it is probably better to let NAND_CTL_CLRALE()
|
|
and company do it.
|
|
|
|
#define NAND_DISABLE_CE(nand)
|
|
Set CE (Chip Enable) low to enable the NAND flash.
|
|
|
|
#define NAND_ENABLE_CE(nand)
|
|
Set CE (Chip Enable) high to disable the NAND flash.
|
|
|
|
#define NAND_CTL_CLRALE(nandptr)
|
|
Set ALE (address latch enable) low. If ALE control is handled by
|
|
WRITE_NAND_ADDRESS() this can be empty.
|
|
|
|
#define NAND_CTL_SETALE(nandptr)
|
|
Set ALE (address latch enable) high. If ALE control is handled by
|
|
WRITE_NAND_ADDRESS() this can be empty.
|
|
|
|
#define NAND_CTL_CLRCLE(nandptr)
|
|
Set CLE (command latch enable) low. If CLE control is handled by
|
|
WRITE_NAND_ADDRESS() this can be empty.
|
|
|
|
#define NAND_CTL_SETCLE(nandptr)
|
|
Set CLE (command latch enable) high. If CLE control is handled by
|
|
WRITE_NAND_ADDRESS() this can be empty.
|
|
|
|
More Definitions:
|
|
|
|
These definitions are needed in the board configuration for now, but
|
|
may really belong in a header file.
|
|
TODO: Figure which ones are truly configuration settings and rename
|
|
them to CFG_NAND_... and move the rest somewhere appropriate.
|
|
|
|
#define SECTORSIZE 512
|
|
#define ADDR_COLUMN 1
|
|
#define ADDR_PAGE 2
|
|
#define ADDR_COLUMN_PAGE 3
|
|
#define NAND_ChipID_UNKNOWN 0x00
|
|
#define NAND_MAX_FLOORS 1
|
|
#define NAND_MAX_CHIPS 1
|