mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-07-05 10:46:15 +09:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com> |
||
|---|---|---|
| .. | ||
| c29xpcie.c | ||
| cpld.c | ||
| cpld.h | ||
| ddr.c | ||
| Kconfig | ||
| law.c | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
| spl_minimal.c | ||
| spl.c | ||
| tlb.c | ||
Overview ========= C29XPCIE board is a series of Freescale PCIe add-in cards to perform as public key crypto accelerator or secure key management module. It includes C293PCIE board, C293PCIE board and C291PCIE board. The Freescale C29x family is a high performance crypto co-processor. It combines a single e500v2 core with necessary SEC engines. (maximum core frequency 1000/1200 MHz). The C29xPCIE board features are as follows: Memory subsystem: - 512Mbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus) - 64 Mbyte NOR flash single-chip memory - 4 Gbyte NAND flash memory - 1 Mbit AT24C1024 I2C EEPROM - 16 Mbyte SPI memory Interfaces: - 10/100/1000 BaseT Ethernet ports: - eTSEC1, RGMII: one 10/100/1000 port - eTSEC2, RGMII: one 10/100/1000 port - DUART interface: - DUART interface: supports two UARTs up to 115200 bps for console display Board connectors: - Mini-ITX power supply connector - JTAG/COP for debugging Physical Memory Map on C29xPCIE =============================== Address Start Address End Memory type 0x0_0000_0000 - 0x0_1fff_ffff 512MB DDR 0xc_0000_0000 - 0xc_8fff_ffff 256MB PCIE memory 0xf_ec00_0000 - 0xf_efff_ffff 64MB NOR flash 0xf_ffb0_0000 - 0xf_ffb7_ffff 512KB SRAM 0xf_ffc0_0000 - 0xf_ffc0_ffff 64KB PCIE IO 0xf_ffdf_0000 - 0xf_ffdf_0fff 4KB CPLD 0xf_ffe0_0000 - 0xf_ffef_ffff 1MB CCSR Serial Port Configuration on C29xPCIE ===================================== Configure the serial port of the attached computer with the following values: -Data rate: 115200 bps -Number of data bits: 8 -Parity: None -Number of Stop bits: 1 -Flow Control: Hardware/None Settings of DIP-switch ====================== SW5[1:4]= 1111 and SW5[6]=0 for boot from 16bit NOR flash SW5[1:4]= 0110 and SW5[6]=0 for boot from SPI flash Note: 1 stands for 'off', 0 stands for 'on' Build and program U-Boot to NOR flash ================================== 1. Build u-boot.bin image example: export ARCH=powerpc export CROSS_COMPILE=/your_path/powerpc-linux-gnu- make C293PCIE 2. Program u-boot.bin into NOR flash => tftp $loadaddr $uboot => protect off eff40000 +$filesize => erase eff40000 +$filesize => cp.b $loadaddr eff40000 $filesize 3. Check SW5[1:4]= 1111 and SW5[6]=0, then power on. Alternate NOR bank ================== There are four banks in C29XPCIE board, example to change bank booting: 1. Program u-boot.bin into alternate NOR bank => tftp $loadaddr $uboot => protect off e9f40000 +$filesize => erase e9f40000 +$filesize => cp.b $loadaddr e9f40000 $filesize 2. Switch to alternate NOR bank => cpld_cmd reset altbank [bank] - [bank] bank value select 1-4 - bank 1 on the flash 0x0000000~0x0ffffff - bank 2 on the flash 0x1000000~0x1ffffff - bank 3 on the flash 0x2000000~0x2ffffff - bank 4 on the flash 0x3000000~0x3ffffff or set SW5[7]= ON/OFF and SW5[7]= ON/OFF, then power on again. Build and program U-Boot to SPI flash ================================== 1. Build u-boot-spi.bin image make C29xPCIE_SPIFLASH_config; make Need the boot_format tool to generate u-boot-spi.bin from the u-boot.bin. 2. Program u-boot-spi.bin into SPI flash => tftp $loadaddr $uboot-spi => sf erase 0 100000 => sf write $loadaddr 0 $filesize 3. Check SW5[1:4]= 0110 and SW5[6]=0, then power on.