mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-09-07 05:13:21 +09:00
![]() Boot Log for i.CoreM6 DualLite/Solo Starter Kit: ----------------------------------------------- U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46) Trying to boot from MMC1 U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530) CPU: Freescale i.MX6SOLO rev1.3 at 792MHz CPU: Industrial temperature grade (-40C to 105C) at 31C Reset cause: POR DRAM: 256 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device switch to partitions #0, OK mmc0 is current device reading boot.scr ** Unable to read file boot.scr ** reading zImage 6741808 bytes read in 341 ms (18.9 MiB/s) Booting from mmc ... reading imx6dl-icore.dtb 30600 bytes read in 19 ms (1.5 MiB/s) Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800a787 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 Boot Log for i.CoreM6 Quad/Dual Starter Kit: -------------------------------------------- U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46) Trying to boot from MMC1 U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530) CPU: Freescale i.MX6Q rev1.2 at 792MHz CPU: Industrial temperature grade (-40C to 105C) at 28C Reset cause: POR DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
||
---|---|---|
.. | ||
icorem6.c | ||
Kconfig | ||
MAINTAINERS | ||
Makefile | ||
README |
How to use U-Boot on Engicam i.CoreM6 DualLite/Solo and Quad/Dual Starter Kit: ----------------------------------------------------------------------------- - Build U-Boot for Engicam i.CoreM6 QDL: $ make mrproper $ make icorem6qdl_mmc_defconfig $ make This will generate the SPL image called SPL and the u-boot.img. - Flash the SPL image into the micro SD card: sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync - Flash the u-boot.img image into the micro SD card: sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync - Jumper settings: MMC Boot: JM3 Closed - Connect the Serial cable between the Starter Kit and the PC for the console. (J28 is the Linux Serial console connector) - Insert the micro SD card in the board, power it up and U-Boot messages should come up. - Note: For loading Linux on Quad/Dual modules set the dtb as icorem6qdl> setenv fdt_file imx6q-icore.dtb