mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-31 14:28:52 +09:00
![Stefan Agner](/assets/img/avatar_default.png)
The motivation for moving MX28 selection to Kconfig is to be able to better handle NAND MXS selection through Kconfig. This selection method also aligns with the way other i.MX SoCs are selected in U-Boot. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
227 lines
7.1 KiB
C
227 lines
7.1 KiB
C
/*
|
|
* Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
|
|
* on behalf of DENX Software Engineering GmbH
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
#ifndef __CONFIGS_M28EVK_H__
|
|
#define __CONFIGS_M28EVK_H__
|
|
|
|
/* System configurations */
|
|
#define CONFIG_MACH_TYPE MACH_TYPE_M28EVK
|
|
|
|
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
|
|
|
|
/* Memory configuration */
|
|
#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
|
|
#define PHYS_SDRAM_1 0x40000000 /* Base address */
|
|
#define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
|
|
/* Environment */
|
|
#define CONFIG_ENV_SIZE (16 * 1024)
|
|
|
|
/* Environment is in NAND */
|
|
#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
|
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
|
|
#define CONFIG_ENV_RANGE (4 * CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_OFFSET (24 * CONFIG_ENV_SECT_SIZE) /* 3 MiB */
|
|
#define CONFIG_ENV_OFFSET_REDUND \
|
|
(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
|
|
|
|
#define CONFIG_MTD_DEVICE
|
|
#define CONFIG_MTD_PARTITIONS
|
|
#endif
|
|
|
|
/* FEC Ethernet on SoC */
|
|
#ifdef CONFIG_CMD_NET
|
|
#define CONFIG_FEC_MXC
|
|
#endif
|
|
|
|
/* RTC */
|
|
#ifdef CONFIG_CMD_DATE
|
|
/* Use the internal RTC in the MXS chip */
|
|
#define CONFIG_RTC_INTERNAL
|
|
#ifdef CONFIG_RTC_INTERNAL
|
|
#define CONFIG_RTC_MXS
|
|
#else
|
|
#define CONFIG_RTC_M41T62
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#define CONFIG_SYS_M41T11_BASE_YEAR 2000
|
|
#endif
|
|
#endif
|
|
|
|
/* USB */
|
|
#ifdef CONFIG_CMD_USB
|
|
#define CONFIG_EHCI_MXS_PORT0
|
|
#define CONFIG_EHCI_MXS_PORT1
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
|
#endif
|
|
|
|
/* SPI */
|
|
#ifdef CONFIG_CMD_SPI
|
|
#define CONFIG_DEFAULT_SPI_BUS 2
|
|
#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0
|
|
|
|
/* SPI FLASH */
|
|
#ifdef CONFIG_CMD_SF
|
|
#define CONFIG_SF_DEFAULT_BUS 2
|
|
#define CONFIG_SF_DEFAULT_CS 0
|
|
#define CONFIG_SF_DEFAULT_SPEED 40000000
|
|
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
|
|
|
|
#define CONFIG_ENV_SPI_BUS 2
|
|
#define CONFIG_ENV_SPI_CS 0
|
|
#define CONFIG_ENV_SPI_MAX_HZ 40000000
|
|
#define CONFIG_ENV_SPI_MODE SPI_MODE_0
|
|
#endif
|
|
|
|
#endif
|
|
|
|
/* LCD */
|
|
#ifdef CONFIG_VIDEO
|
|
#define CONFIG_VIDEO_LOGO
|
|
#define CONFIG_SPLASH_SCREEN
|
|
#define CONFIG_BMP_16BPP
|
|
#define CONFIG_VIDEO_BMP_RLE8
|
|
#define CONFIG_VIDEO_BMP_GZIP
|
|
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
|
|
#endif
|
|
|
|
/* Booting Linux */
|
|
#define CONFIG_BOOTFILE "fitImage"
|
|
#define CONFIG_BOOTCOMMAND "run mmc_mmc"
|
|
#define CONFIG_LOADADDR 0x42000000
|
|
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
|
|
|
|
/* Extra Environment */
|
|
#define CONFIG_PREBOOT "run try_bootscript"
|
|
#define CONFIG_HOSTNAME m28evk
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"consdev=ttyAMA0\0" \
|
|
"baudrate=115200\0" \
|
|
"bootscript=boot.scr\0" \
|
|
"bootdev=/dev/mmcblk0p2\0" \
|
|
"rootdev=/dev/mmcblk0p3\0" \
|
|
"netdev=eth0\0" \
|
|
"hostname=m28evk\0" \
|
|
"rootpath=/opt/eldk-5.5/armv5te/rootfs-qte-sdk\0" \
|
|
"kernel_addr_r=0x42000000\0" \
|
|
"videomode=video=ctfb:x:800,y:480,depth:18,mode:0,pclk:30066," \
|
|
"le:0,ri:256,up:0,lo:45,hs:1,vs:1,sync:100663296," \
|
|
"vmode:0\0" \
|
|
"update_nand_full_filename=u-boot.nand\0" \
|
|
"update_nand_firmware_filename=u-boot.sb\0" \
|
|
"update_sd_firmware_filename=u-boot.sd\0" \
|
|
"update_nand_firmware_maxsz=0x100000\0" \
|
|
"update_nand_stride=0x40\0" /* MX28 datasheet ch. 12.12 */ \
|
|
"update_nand_count=0x4\0" /* MX28 datasheet ch. 12.12 */ \
|
|
"update_nand_get_fcb_size=" /* Get size of FCB blocks */ \
|
|
"nand device 0 ; " \
|
|
"nand info ; " \
|
|
"setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
|
|
"setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
|
|
"update_nand_full=" /* Update FCB, DBBT and FW */ \
|
|
"if tftp ${update_nand_full_filename} ; then " \
|
|
"run update_nand_get_fcb_size ; " \
|
|
"nand scrub -y 0x0 ${filesize} ; " \
|
|
"nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; " \
|
|
"setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
|
|
"setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
|
|
"nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
|
|
"fi\0" \
|
|
"update_nand_firmware=" /* Update only firmware */ \
|
|
"if tftp ${update_nand_firmware_filename} ; then " \
|
|
"run update_nand_get_fcb_size ; " \
|
|
"setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
|
|
"setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; " \
|
|
"setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
|
|
"nand erase ${fcb_sz} ${fw_sz} ; " \
|
|
"nand write ${loadaddr} ${fcb_sz} ${filesize} ; " \
|
|
"nand write ${loadaddr} ${fw_off} ${filesize} ; " \
|
|
"fi\0" \
|
|
"update_sd_firmware=" /* Update the SD firmware partition */ \
|
|
"if mmc rescan ; then " \
|
|
"if tftp ${update_sd_firmware_filename} ; then " \
|
|
"setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \
|
|
"setexpr fw_sz ${fw_sz} + 1 ; " \
|
|
"mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
|
|
"fi ; " \
|
|
"fi\0" \
|
|
"addcons=" \
|
|
"setenv bootargs ${bootargs} " \
|
|
"console=${consdev},${baudrate}\0" \
|
|
"addip=" \
|
|
"setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:" \
|
|
"${netmask}:${hostname}:${netdev}:off\0" \
|
|
"addmisc=" \
|
|
"setenv bootargs ${bootargs} ${miscargs}\0" \
|
|
"adddfltmtd=" \
|
|
"if test \"x${mtdparts}\" == \"x\" ; then " \
|
|
"mtdparts default ; " \
|
|
"fi\0" \
|
|
"addmtd=" \
|
|
"run adddfltmtd ; " \
|
|
"setenv bootargs ${bootargs} ${mtdparts}\0" \
|
|
"addargs=run addcons addmtd addmisc\0" \
|
|
"mmcload=" \
|
|
"mmc rescan ; " \
|
|
"load mmc 0:2 ${kernel_addr_r} ${bootfile}\0" \
|
|
"ubiload=" \
|
|
"ubi part UBI ; ubifsmount ubi0:rootfs ; " \
|
|
"ubifsload ${kernel_addr_r} /boot/${bootfile}\0" \
|
|
"netload=" \
|
|
"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \
|
|
"miscargs=nohlt panic=1\0" \
|
|
"mmcargs=setenv bootargs root=${rootdev} rw rootwait\0" \
|
|
"ubiargs=" \
|
|
"setenv bootargs ubi.mtd=5 " \
|
|
"root=ubi0:rootfs rootfstype=ubifs\0" \
|
|
"nfsargs=" \
|
|
"setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath},v3,tcp\0" \
|
|
"mmc_mmc=" \
|
|
"run mmcload mmcargs addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"mmc_ubi=" \
|
|
"run mmcload ubiargs addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"mmc_nfs=" \
|
|
"run mmcload nfsargs addip addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"ubi_mmc=" \
|
|
"run ubiload mmcargs addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"ubi_ubi=" \
|
|
"run ubiload ubiargs addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"ubi_nfs=" \
|
|
"run ubiload nfsargs addip addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"net_mmc=" \
|
|
"run netload mmcargs addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"net_ubi=" \
|
|
"run netload ubiargs addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"net_nfs=" \
|
|
"run netload nfsargs addip addargs ; " \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"try_bootscript=" \
|
|
"mmc rescan;" \
|
|
"if test -e mmc 0:2 ${bootscript} ; then " \
|
|
"if load mmc 0:2 ${kernel_addr_r} ${bootscript};" \
|
|
"then ; " \
|
|
"echo Running bootscript... ; " \
|
|
"source ${kernel_addr_r} ; " \
|
|
"fi ; " \
|
|
"fi\0"
|
|
|
|
/* The rest of the configuration is shared */
|
|
#include <configs/mxs.h>
|
|
|
|
#endif /* __CONFIGS_M28EVK_H__ */
|