brain-hackers_pepepper-mirror/u-boot-brain
1
0
Fork 0
mirror of https://github.com/brain-hackers/u-boot-brain synced 2024-06-09 23:36:03 +09:00
Code Issues Projects Releases Wiki Activity
927c1fa266
u-boot-brain/drivers/spi/fsl_qspi.c
Peng Fan 5f7f70c171 qspi:fsl implement AHB read 
The QSPI controller in i.MX 6SoloX and Vybrid supports reading data using
IP register and AHB bus.

The original driver only supports reading data from IP interface. The IC
team suggests to use AHB read which is faster then IP read. Using AHB read,
we can directly memcpy, a "missed" access to the buffer will cause the
controller to clear the buffer and use the SEQID stored in bfgencr register
to initiate a read from flash device.

Since AHB bus is 64 bit width, we can not set MCR register using 32bit. In
order to minimize code change, redefine QSPI_MCR_END_CFD_LE to 64bit Little
endian but not 32bit Little endia.

Introduce a new configuration option CONFIG_SYS_FSL_QSPI_AHB. If want to
use AHB read, just define CONFIG_SYS_FSL_QSPI_AHB. If not, just ignore it.
Actually if Vybrid is migrated to use AHB read, this option can be removed and
IP read function can be discared. The reason to introduce this option
is that only i.MX SOC is tested in my side, no Vybrid platform for me.

In spi_setup_slave, the original piece code to set AHB is deleted, since
Vybrid platform does not use this to intiate AHB read. Instead, add
qspi_init_ahb_read function if defined CONFIG_SYS_FSL_QSPI_AHB.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-09 00:03:28 +05:30

785 lines
22 KiB
C
Raw Blame History

/*
* Copyright 2013-2014 Freescale Semiconductor, Inc.
*
* Freescale Quad Serial Peripheral Interface (QSPI) driver
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <malloc.h>
#include <spi.h>
#include <asm/io.h>
#include <linux/sizes.h>
#include "fsl_qspi.h"
#define RX_BUFFER_SIZE 0x80
#ifdef CONFIG_MX6SX
#define TX_BUFFER_SIZE 0x200
#else
#define TX_BUFFER_SIZE 0x40
#endif
#define OFFSET_BITS_MASK 0x00ffffff
#define FLASH_STATUS_WEL 0x02
/* SEQID */
#define SEQID_WREN 1
#define SEQID_FAST_READ 2
#define SEQID_RDSR 3
#define SEQID_SE 4
#define SEQID_CHIP_ERASE 5
#define SEQID_PP 6
#define SEQID_RDID 7
#define SEQID_BE_4K 8
#ifdef CONFIG_SPI_FLASH_BAR
#define SEQID_BRRD 9
#define SEQID_BRWR 10
#define SEQID_RDEAR 11
#define SEQID_WREAR 12
#endif
/* QSPI CMD */
#define QSPI_CMD_PP 0x02 /* Page program (up to 256 bytes) */
#define QSPI_CMD_RDSR 0x05 /* Read status register */
#define QSPI_CMD_WREN 0x06 /* Write enable */
#define QSPI_CMD_FAST_READ 0x0b /* Read data bytes (high frequency) */
#define QSPI_CMD_BE_4K 0x20 /* 4K erase */
#define QSPI_CMD_CHIP_ERASE 0xc7 /* Erase whole flash chip */
#define QSPI_CMD_SE 0xd8 /* Sector erase (usually 64KiB) */
#define QSPI_CMD_RDID 0x9f /* Read JEDEC ID */
/* Used for Micron, winbond and Macronix flashes */
#define QSPI_CMD_WREAR 0xc5 /* EAR register write */
#define QSPI_CMD_RDEAR 0xc8 /* EAR reigster read */
/* Used for Spansion flashes only. */
#define QSPI_CMD_BRRD 0x16 /* Bank register read */
#define QSPI_CMD_BRWR 0x17 /* Bank register write */
/* 4-byte address QSPI CMD - used on Spansion and some Macronix flashes */
#define QSPI_CMD_FAST_READ_4B 0x0c /* Read data bytes (high frequency) */
#define QSPI_CMD_PP_4B 0x12 /* Page program (up to 256 bytes) */
#define QSPI_CMD_SE_4B 0xdc /* Sector erase (usually 64KiB) */
#ifdef CONFIG_SYS_FSL_QSPI_LE
#define qspi_read32 in_le32
#define qspi_write32 out_le32
#elif defined(CONFIG_SYS_FSL_QSPI_BE)
#define qspi_read32 in_be32
#define qspi_write32 out_be32
#endif
static unsigned long spi_bases[] = {
QSPI0_BASE_ADDR,
#ifdef CONFIG_MX6SX
QSPI1_BASE_ADDR,
#endif
};
static unsigned long amba_bases[] = {
QSPI0_AMBA_BASE,
#ifdef CONFIG_MX6SX
QSPI1_AMBA_BASE,
#endif
};
struct fsl_qspi {
struct spi_slave slave;
unsigned long reg_base;
unsigned long amba_base;
u32 sf_addr;
u8 cur_seqid;
};
/* QSPI support swapping the flash read/write data
* in hardware for LS102xA, but not for VF610 */
static inline u32 qspi_endian_xchg(u32 data)
{
#ifdef CONFIG_VF610
return swab32(data);
#else
return data;
#endif
}
static inline struct fsl_qspi *to_qspi_spi(struct spi_slave *slave)
{
return container_of(slave, struct fsl_qspi, slave);
}
static void qspi_set_lut(struct fsl_qspi *qspi)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)qspi->reg_base;
u32 lut_base;
/* Unlock the LUT */
qspi_write32(&regs->lutkey, LUT_KEY_VALUE);
qspi_write32(&regs->lckcr, QSPI_LCKCR_UNLOCK);
/* Write Enable */
lut_base = SEQID_WREN * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_WREN) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD));
qspi_write32(&regs->lut[lut_base + 1], 0);
qspi_write32(&regs->lut[lut_base + 2], 0);
qspi_write32(&regs->lut[lut_base + 3], 0);
/* Fast Read */
lut_base = SEQID_FAST_READ * 4;
#ifdef CONFIG_SPI_FLASH_BAR
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_FAST_READ) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
#else
if (FSL_QSPI_FLASH_SIZE <= SZ_16M)
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_FAST_READ) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
else
qspi_write32(&regs->lut[lut_base],
OPRND0(QSPI_CMD_FAST_READ_4B) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) |
OPRND1(ADDR32BIT) | PAD1(LUT_PAD1) |
INSTR1(LUT_ADDR));
#endif
qspi_write32(&regs->lut[lut_base + 1], OPRND0(8) | PAD0(LUT_PAD1) |
INSTR0(LUT_DUMMY) | OPRND1(RX_BUFFER_SIZE) | PAD1(LUT_PAD1) |
INSTR1(LUT_READ));
qspi_write32(&regs->lut[lut_base + 2], 0);
qspi_write32(&regs->lut[lut_base + 3], 0);
/* Read Status */
lut_base = SEQID_RDSR * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_RDSR) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) |
PAD1(LUT_PAD1) | INSTR1(LUT_READ));
qspi_write32(&regs->lut[lut_base + 1], 0);
qspi_write32(&regs->lut[lut_base + 2], 0);
qspi_write32(&regs->lut[lut_base + 3], 0);
/* Erase a sector */
lut_base = SEQID_SE * 4;
#ifdef CONFIG_SPI_FLASH_BAR
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_SE) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
#else
if (FSL_QSPI_FLASH_SIZE <= SZ_16M)
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_SE) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
else
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_SE_4B) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR32BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
#endif
qspi_write32(&regs->lut[lut_base + 1], 0);
qspi_write32(&regs->lut[lut_base + 2], 0);
qspi_write32(&regs->lut[lut_base + 3], 0);
/* Erase the whole chip */
lut_base = SEQID_CHIP_ERASE * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_CHIP_ERASE) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD));
qspi_write32(&regs->lut[lut_base + 1], 0);
qspi_write32(&regs->lut[lut_base + 2], 0);
qspi_write32(&regs->lut[lut_base + 3], 0);
/* Page Program */
lut_base = SEQID_PP * 4;
#ifdef CONFIG_SPI_FLASH_BAR
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_PP) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
#else
if (FSL_QSPI_FLASH_SIZE <= SZ_16M)
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_PP) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
else
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_PP_4B) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR32BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
#endif
#ifdef CONFIG_MX6SX
/*
* To MX6SX, OPRND0(TX_BUFFER_SIZE) can not work correctly.
* So, Use IDATSZ in IPCR to determine the size and here set 0.
*/
qspi_write32(&regs->lut[lut_base + 1], OPRND0(0) |
PAD0(LUT_PAD1) | INSTR0(LUT_WRITE));
#else
qspi_write32(&regs->lut[lut_base + 1], OPRND0(TX_BUFFER_SIZE) |
PAD0(LUT_PAD1) | INSTR0(LUT_WRITE));
#endif
qspi_write32(&regs->lut[lut_base + 2], 0);
qspi_write32(&regs->lut[lut_base + 3], 0);
/* READ ID */
lut_base = SEQID_RDID * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_RDID) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(8) |
PAD1(LUT_PAD1) | INSTR1(LUT_READ));
qspi_write32(&regs->lut[lut_base + 1], 0);
qspi_write32(&regs->lut[lut_base + 2], 0);
qspi_write32(&regs->lut[lut_base + 3], 0);
/* SUB SECTOR 4K ERASE */
lut_base = SEQID_BE_4K * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_BE_4K) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) |
PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
#ifdef CONFIG_SPI_FLASH_BAR
/*
* BRRD BRWR RDEAR WREAR are all supported, because it is hard to
* dynamically check whether to set BRRD BRWR or RDEAR WREAR during
* initialization.
*/
lut_base = SEQID_BRRD * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_BRRD) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) |
PAD1(LUT_PAD1) | INSTR1(LUT_READ));
lut_base = SEQID_BRWR * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_BRWR) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) |
PAD1(LUT_PAD1) | INSTR1(LUT_WRITE));
lut_base = SEQID_RDEAR * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_RDEAR) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) |
PAD1(LUT_PAD1) | INSTR1(LUT_READ));
lut_base = SEQID_WREAR * 4;
qspi_write32(&regs->lut[lut_base], OPRND0(QSPI_CMD_WREAR) |
PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) |
PAD1(LUT_PAD1) | INSTR1(LUT_WRITE));
#endif
/* Lock the LUT */
qspi_write32(&regs->lutkey, LUT_KEY_VALUE);
qspi_write32(&regs->lckcr, QSPI_LCKCR_LOCK);
}
#if defined(CONFIG_SYS_FSL_QSPI_AHB)
/*
* If we have changed the content of the flash by writing or erasing,
* we need to invalidate the AHB buffer. If we do not do so, we may read out
* the wrong data. The spec tells us reset the AHB domain and Serial Flash
* domain at the same time.
*/
static inline void qspi_ahb_invalid(struct fsl_qspi *q)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)q->reg_base;
u32 reg;
reg = qspi_read32(&regs->mcr);
reg |= QSPI_MCR_SWRSTHD_MASK | QSPI_MCR_SWRSTSD_MASK;
qspi_write32(&regs->mcr, reg);
/*
* The minimum delay : 1 AHB + 2 SFCK clocks.
* Delay 1 us is enough.
*/
udelay(1);
reg &= ~(QSPI_MCR_SWRSTHD_MASK | QSPI_MCR_SWRSTSD_MASK);
qspi_write32(&regs->mcr, reg);
}
/* Read out the data from the AHB buffer. */
static inline void qspi_ahb_read(struct fsl_qspi *q, u8 *rxbuf, int len)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)q->reg_base;
u32 mcr_reg;
mcr_reg = qspi_read32(&regs->mcr);
qspi_write32(&regs->mcr, QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK |
QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE);
/* Read out the data directly from the AHB buffer. */
memcpy(rxbuf, (u8 *)(q->amba_base + q->sf_addr), len);
qspi_write32(&regs->mcr, mcr_reg);
}
static void qspi_enable_ddr_mode(struct fsl_qspi_regs *regs)
{
u32 reg, reg2;
reg = qspi_read32(&regs->mcr);
/* Disable the module */
qspi_write32(&regs->mcr, reg | QSPI_MCR_MDIS_MASK);
/* Set the Sampling Register for DDR */
reg2 = qspi_read32(&regs->smpr);
reg2 &= ~QSPI_SMPR_DDRSMP_MASK;
reg2 |= (2 << QSPI_SMPR_DDRSMP_SHIFT);
qspi_write32(&regs->smpr, reg2);
/* Enable the module again (enable the DDR too) */
reg |= QSPI_MCR_DDR_EN_MASK;
/* Enable bit 29 for imx6sx */
reg |= (1 << 29);
qspi_write32(&regs->mcr, reg);
}
/*
* There are two different ways to read out the data from the flash:
* the "IP Command Read" and the "AHB Command Read".
*
* The IC guy suggests we use the "AHB Command Read" which is faster
* then the "IP Command Read". (What's more is that there is a bug in
* the "IP Command Read" in the Vybrid.)
*
* After we set up the registers for the "AHB Command Read", we can use
* the memcpy to read the data directly. A "missed" access to the buffer
* causes the controller to clear the buffer, and use the sequence pointed
* by the QUADSPI_BFGENCR[SEQID] to initiate a read from the flash.
*/
static void qspi_init_ahb_read(struct fsl_qspi_regs *regs)
{
/* AHB configuration for access buffer 0/1/2 .*/
qspi_write32(&regs->buf0cr, QSPI_BUFXCR_INVALID_MSTRID);
qspi_write32(&regs->buf1cr, QSPI_BUFXCR_INVALID_MSTRID);
qspi_write32(&regs->buf2cr, QSPI_BUFXCR_INVALID_MSTRID);
qspi_write32(&regs->buf3cr, QSPI_BUF3CR_ALLMST_MASK |
(0x80 << QSPI_BUF3CR_ADATSZ_SHIFT));
/* We only use the buffer3 */
qspi_write32(&regs->buf0ind, 0);
qspi_write32(&regs->buf1ind, 0);
qspi_write32(&regs->buf2ind, 0);
/*
* Set the default lut sequence for AHB Read.
* Parallel mode is disabled.
*/
qspi_write32(&regs->bfgencr,
SEQID_FAST_READ << QSPI_BFGENCR_SEQID_SHIFT);
/*Enable DDR Mode*/
qspi_enable_ddr_mode(regs);
}
#endif
void spi_init()
{
/* do nothing */
}
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
unsigned int max_hz, unsigned int mode)
{
struct fsl_qspi *qspi;
struct fsl_qspi_regs *regs;
u32 smpr_val;
u32 total_size;
if (bus >= ARRAY_SIZE(spi_bases))
return NULL;
if (cs >= FSL_QSPI_FLASH_NUM)
return NULL;
qspi = spi_alloc_slave(struct fsl_qspi, bus, cs);
if (!qspi)
return NULL;
qspi->reg_base = spi_bases[bus];
/*
* According cs, use different amba_base to choose the
* corresponding flash devices.
*
* If not, only one flash device is used even if passing
* different cs using `sf probe`
*/
qspi->amba_base = amba_bases[bus] + cs * FSL_QSPI_FLASH_SIZE;
qspi->slave.max_write_size = TX_BUFFER_SIZE;
regs = (struct fsl_qspi_regs *)qspi->reg_base;
qspi_write32(&regs->mcr, QSPI_MCR_RESERVED_MASK | QSPI_MCR_MDIS_MASK);
smpr_val = qspi_read32(&regs->smpr);
qspi_write32(&regs->smpr, smpr_val & ~(QSPI_SMPR_FSDLY_MASK |
QSPI_SMPR_FSPHS_MASK | QSPI_SMPR_HSENA_MASK));
qspi_write32(&regs->mcr, QSPI_MCR_RESERVED_MASK);
total_size = FSL_QSPI_FLASH_SIZE * FSL_QSPI_FLASH_NUM;
/*
* Any read access to non-implemented addresses will provide
* undefined results.
*
* In case single die flash devices, TOP_ADDR_MEMA2 and
* TOP_ADDR_MEMB2 should be initialized/programmed to
* TOP_ADDR_MEMA1 and TOP_ADDR_MEMB1 respectively - in effect,
* setting the size of these devices to 0. This would ensure
* that the complete memory map is assigned to only one flash device.
*/
qspi_write32(&regs->sfa1ad, FSL_QSPI_FLASH_SIZE | amba_bases[bus]);
qspi_write32(&regs->sfa2ad, FSL_QSPI_FLASH_SIZE | amba_bases[bus]);
qspi_write32(&regs->sfb1ad, total_size | amba_bases[bus]);
qspi_write32(&regs->sfb2ad, total_size | amba_bases[bus]);
qspi_set_lut(qspi);
smpr_val = qspi_read32(&regs->smpr);
smpr_val &= ~QSPI_SMPR_DDRSMP_MASK;
qspi_write32(&regs->smpr, smpr_val);
qspi_write32(&regs->mcr, QSPI_MCR_RESERVED_MASK);
#ifdef CONFIG_SYS_FSL_QSPI_AHB
qspi_init_ahb_read(regs);
#endif
return &qspi->slave;
}
void spi_free_slave(struct spi_slave *slave)
{
struct fsl_qspi *qspi = to_qspi_spi(slave);
free(qspi);
}
int spi_claim_bus(struct spi_slave *slave)
{
return 0;
}
#ifdef CONFIG_SPI_FLASH_BAR
/* Bank register read/write, EAR register read/write */
static void qspi_op_rdbank(struct fsl_qspi *qspi, u8 *rxbuf, u32 len)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)qspi->reg_base;
u32 reg, mcr_reg, data, seqid;
mcr_reg = qspi_read32(&regs->mcr);
qspi_write32(&regs->mcr, QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK |
QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE);
qspi_write32(&regs->rbct, QSPI_RBCT_RXBRD_USEIPS);
qspi_write32(&regs->sfar, qspi->amba_base);
if (qspi->cur_seqid == QSPI_CMD_BRRD)
seqid = SEQID_BRRD;
else
seqid = SEQID_RDEAR;
qspi_write32(&regs->ipcr, (seqid << QSPI_IPCR_SEQID_SHIFT) | len);
/* Wait previous command complete */
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
while (1) {
reg = qspi_read32(&regs->rbsr);
if (reg & QSPI_RBSR_RDBFL_MASK) {
data = qspi_read32(&regs->rbdr[0]);
data = qspi_endian_xchg(data);
memcpy(rxbuf, &data, len);
qspi_write32(&regs->mcr, qspi_read32(&regs->mcr) |
QSPI_MCR_CLR_RXF_MASK);
break;
}
}
qspi_write32(&regs->mcr, mcr_reg);
}
#endif
static void qspi_op_rdid(struct fsl_qspi *qspi, u32 *rxbuf, u32 len)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)qspi->reg_base;
u32 mcr_reg, rbsr_reg, data;
int i, size;
mcr_reg = qspi_read32(&regs->mcr);
qspi_write32(&regs->mcr, QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK |
QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE);
qspi_write32(&regs->rbct, QSPI_RBCT_RXBRD_USEIPS);
qspi_write32(&regs->sfar, qspi->amba_base);
qspi_write32(&regs->ipcr, (SEQID_RDID << QSPI_IPCR_SEQID_SHIFT) | 0);
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
i = 0;
size = len;
while ((RX_BUFFER_SIZE >= size) && (size > 0)) {
rbsr_reg = qspi_read32(&regs->rbsr);
if (rbsr_reg & QSPI_RBSR_RDBFL_MASK) {
data = qspi_read32(&regs->rbdr[i]);
data = qspi_endian_xchg(data);
memcpy(rxbuf, &data, 4);
rxbuf++;
size -= 4;
i++;
}
}
qspi_write32(&regs->mcr, mcr_reg);
}
#ifndef CONFIG_SYS_FSL_QSPI_AHB
/* If not use AHB read, read data from ip interface */
static void qspi_op_read(struct fsl_qspi *qspi, u32 *rxbuf, u32 len)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)qspi->reg_base;
u32 mcr_reg, data;
int i, size;
u32 to_or_from;
mcr_reg = qspi_read32(&regs->mcr);
qspi_write32(&regs->mcr, QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK |
QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE);
qspi_write32(&regs->rbct, QSPI_RBCT_RXBRD_USEIPS);
to_or_from = qspi->sf_addr + qspi->amba_base;
while (len > 0) {
qspi_write32(&regs->sfar, to_or_from);
size = (len > RX_BUFFER_SIZE) ?
RX_BUFFER_SIZE : len;
qspi_write32(&regs->ipcr,
(SEQID_FAST_READ << QSPI_IPCR_SEQID_SHIFT) | size);
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
to_or_from += size;
len -= size;
i = 0;
while ((RX_BUFFER_SIZE >= size) && (size > 0)) {
data = qspi_read32(&regs->rbdr[i]);
data = qspi_endian_xchg(data);
memcpy(rxbuf, &data, 4);
rxbuf++;
size -= 4;
i++;
}
qspi_write32(&regs->mcr, qspi_read32(&regs->mcr) |
QSPI_MCR_CLR_RXF_MASK);
}
qspi_write32(&regs->mcr, mcr_reg);
}
#endif
static void qspi_op_write(struct fsl_qspi *qspi, u8 *txbuf, u32 len)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)qspi->reg_base;
u32 mcr_reg, data, reg, status_reg, seqid;
int i, size, tx_size;
u32 to_or_from = 0;
mcr_reg = qspi_read32(&regs->mcr);
qspi_write32(&regs->mcr, QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK |
QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE);
qspi_write32(&regs->rbct, QSPI_RBCT_RXBRD_USEIPS);
status_reg = 0;
while ((status_reg & FLASH_STATUS_WEL) != FLASH_STATUS_WEL) {
qspi_write32(&regs->ipcr,
(SEQID_WREN << QSPI_IPCR_SEQID_SHIFT) | 0);
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
qspi_write32(&regs->ipcr,
(SEQID_RDSR << QSPI_IPCR_SEQID_SHIFT) | 1);
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
reg = qspi_read32(&regs->rbsr);
if (reg & QSPI_RBSR_RDBFL_MASK) {
status_reg = qspi_read32(&regs->rbdr[0]);
status_reg = qspi_endian_xchg(status_reg);
}
qspi_write32(&regs->mcr,
qspi_read32(&regs->mcr) | QSPI_MCR_CLR_RXF_MASK);
}
/* Default is page programming */
seqid = SEQID_PP;
#ifdef CONFIG_SPI_FLASH_BAR
if (qspi->cur_seqid == QSPI_CMD_BRWR)
seqid = SEQID_BRWR;
else if (qspi->cur_seqid == QSPI_CMD_WREAR)
seqid = SEQID_WREAR;
#endif
to_or_from = qspi->sf_addr + qspi->amba_base;
qspi_write32(&regs->sfar, to_or_from);
tx_size = (len > TX_BUFFER_SIZE) ?
TX_BUFFER_SIZE : len;
size = tx_size / 4;
for (i = 0; i < size; i++) {
memcpy(&data, txbuf, 4);
data = qspi_endian_xchg(data);
qspi_write32(&regs->tbdr, data);
txbuf += 4;
}
size = tx_size % 4;
if (size) {
data = 0;
memcpy(&data, txbuf, size);
data = qspi_endian_xchg(data);
qspi_write32(&regs->tbdr, data);
}
qspi_write32(&regs->ipcr, (seqid << QSPI_IPCR_SEQID_SHIFT) | tx_size);
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
qspi_write32(&regs->mcr, mcr_reg);
}
static void qspi_op_rdsr(struct fsl_qspi *qspi, u32 *rxbuf)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)qspi->reg_base;
u32 mcr_reg, reg, data;
mcr_reg = qspi_read32(&regs->mcr);
qspi_write32(&regs->mcr, QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK |
QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE);
qspi_write32(&regs->rbct, QSPI_RBCT_RXBRD_USEIPS);
qspi_write32(&regs->sfar, qspi->amba_base);
qspi_write32(&regs->ipcr,
(SEQID_RDSR << QSPI_IPCR_SEQID_SHIFT) | 0);
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
while (1) {
reg = qspi_read32(&regs->rbsr);
if (reg & QSPI_RBSR_RDBFL_MASK) {
data = qspi_read32(&regs->rbdr[0]);
data = qspi_endian_xchg(data);
memcpy(rxbuf, &data, 4);
qspi_write32(&regs->mcr, qspi_read32(&regs->mcr) |
QSPI_MCR_CLR_RXF_MASK);
break;
}
}
qspi_write32(&regs->mcr, mcr_reg);
}
static void qspi_op_erase(struct fsl_qspi *qspi)
{
struct fsl_qspi_regs *regs = (struct fsl_qspi_regs *)qspi->reg_base;
u32 mcr_reg;
u32 to_or_from = 0;
mcr_reg = qspi_read32(&regs->mcr);
qspi_write32(&regs->mcr, QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK |
QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE);
qspi_write32(&regs->rbct, QSPI_RBCT_RXBRD_USEIPS);
to_or_from = qspi->sf_addr + qspi->amba_base;
qspi_write32(&regs->sfar, to_or_from);
qspi_write32(&regs->ipcr,
(SEQID_WREN << QSPI_IPCR_SEQID_SHIFT) | 0);
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
if (qspi->cur_seqid == QSPI_CMD_SE) {
qspi_write32(&regs->ipcr,
(SEQID_SE << QSPI_IPCR_SEQID_SHIFT) | 0);
} else if (qspi->cur_seqid == QSPI_CMD_BE_4K) {
qspi_write32(&regs->ipcr,
(SEQID_BE_4K << QSPI_IPCR_SEQID_SHIFT) | 0);
}
while (qspi_read32(&regs->sr) & QSPI_SR_BUSY_MASK)
;
qspi_write32(&regs->mcr, mcr_reg);
}
int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
const void *dout, void *din, unsigned long flags)
{
struct fsl_qspi *qspi = to_qspi_spi(slave);
u32 bytes = DIV_ROUND_UP(bitlen, 8);
static u32 wr_sfaddr;
u32 txbuf;
if (dout) {
if (flags & SPI_XFER_BEGIN) {
qspi->cur_seqid = *(u8 *)dout;
memcpy(&txbuf, dout, 4);
}
if (flags == SPI_XFER_END) {
qspi->sf_addr = wr_sfaddr;
qspi_op_write(qspi, (u8 *)dout, bytes);
return 0;
}
if (qspi->cur_seqid == QSPI_CMD_FAST_READ) {
qspi->sf_addr = swab32(txbuf) & OFFSET_BITS_MASK;
} else if ((qspi->cur_seqid == QSPI_CMD_SE) ||
(qspi->cur_seqid == QSPI_CMD_BE_4K)) {
qspi->sf_addr = swab32(txbuf) & OFFSET_BITS_MASK;
qspi_op_erase(qspi);
} else if (qspi->cur_seqid == QSPI_CMD_PP)
wr_sfaddr = swab32(txbuf) & OFFSET_BITS_MASK;
#ifdef CONFIG_SPI_FLASH_BAR
else if ((qspi->cur_seqid == QSPI_CMD_BRWR) ||
(qspi->cur_seqid == QSPI_CMD_WREAR)) {
wr_sfaddr = 0;
}
#endif
}
if (din) {
if (qspi->cur_seqid == QSPI_CMD_FAST_READ) {
#ifdef CONFIG_SYS_FSL_QSPI_AHB
qspi_ahb_read(qspi, din, bytes);
#else
qspi_op_read(qspi, din, bytes);
#endif
}
else if (qspi->cur_seqid == QSPI_CMD_RDID)
qspi_op_rdid(qspi, din, bytes);
else if (qspi->cur_seqid == QSPI_CMD_RDSR)
qspi_op_rdsr(qspi, din);
#ifdef CONFIG_SPI_FLASH_BAR
else if ((qspi->cur_seqid == QSPI_CMD_BRRD) ||
(qspi->cur_seqid == QSPI_CMD_RDEAR)) {
qspi->sf_addr = 0;
qspi_op_rdbank(qspi, din, bytes);
}
#endif
}
#ifdef CONFIG_SYS_FSL_QSPI_AHB
if ((qspi->cur_seqid == QSPI_CMD_SE) ||
(qspi->cur_seqid == QSPI_CMD_PP) ||
(qspi->cur_seqid == QSPI_CMD_BE_4K) ||
(qspi->cur_seqid == QSPI_CMD_WREAR) ||
(qspi->cur_seqid == QSPI_CMD_BRWR))
qspi_ahb_invalid(qspi);
#endif
return 0;
}
void spi_release_bus(struct spi_slave *slave)
{
/* Nothing to do */
}
Reference in New Issue View Git Blame Copy Permalink