mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-07-10 13:16:16 +09:00
90526e9fba
Move this header out of the common header. Network support is used in quite a few places but it still does not warrant blanket inclusion. Note that this net.h header itself has quite a lot in it. It could be split into the driver-mode support, functions, structures, checksumming, etc. Signed-off-by: Simon Glass <sjg@chromium.org> |
||
|---|---|---|
| .. | ||
| MAINTAINERS | ||
| Makefile | ||
| p201.c | ||
| README.p201 | ||
U-Boot for Amlogic P201 ======================= P201 is a reference board manufactured by Amlogic with the following specifications: - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz - ARM Mali 450 GPU - 2GB DDR3 SDRAM - 10/100 Ethernet - HDMI 2.0 4K/60Hz display - 2 x USB 2.0 Host - eMMC, microSD - Infrared receiver - SDIO WiFi Module - CVBS+Stereo Audio Jack Schematics are available from Amlogic on demand. Currently the u-boot port supports the following devices: - serial - eMMC, microSD - Ethernet - I2C - Regulators - Reset controller - Clock controller - USB Host - ADC u-boot compilation ================== > export ARCH=arm > export CROSS_COMPILE=aarch64-none-elf- > make p201_defconfig > make Image creation ============== Amlogic doesn't provide sources for the firmware and for tools needed to create the bootloader image, so it is necessary to obtain them from the git tree published by the board vendor: > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH > git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot > cd amlogic-u-boot > make gxb_p201_v1_defconfig > make > export FIPDIR=$PWD/fip Go back to mainline U-boot source tree then : > mkdir fip > cp $FIPDIR/gxl/bl2.bin fip/ > cp $FIPDIR/gxl/acs.bin fip/ > cp $FIPDIR/gxl/bl21.bin fip/ > cp $FIPDIR/gxl/bl30.bin fip/ > cp $FIPDIR/gxl/bl301.bin fip/ > cp $FIPDIR/gxl/bl31.img fip/ > cp u-boot.bin fip/bl33.bin > $FIPDIR/blx_fix.sh \ fip/bl30.bin \ fip/zero_tmp \ fip/bl30_zero.bin \ fip/bl301.bin \ fip/bl301_zero.bin \ fip/bl30_new.bin \ bl30 > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 > $FIPDIR/blx_fix.sh \ fip/bl2_acs.bin \ fip/zero_tmp \ fip/bl2_zero.bin \ fip/bl21.bin \ fip/bl21_zero.bin \ fip/bl2_new.bin \ bl2 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ --output fip/u-boot.bin \ --bl2 fip/bl2.n.bin.sig \ --bl30 fip/bl30_new.bin.enc \ --bl31 fip/bl31.img.enc \ --bl33 fip/bl33.bin.enc and then write the image to SD with: > DEV=/dev/your_sd_device > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444