brain-hackers_pepepper-mirror/u-boot-brain
1
0
Fork 0
mirror of https://github.com/brain-hackers/u-boot-brain synced 2024-06-09 23:36:03 +09:00
Code Issues Projects Releases Wiki Activity
8974ff1a60
u-boot-brain/drivers/mmc/fsl_esdhc_imx.c
Haibo Chen 8974ff1a60 mmc: fsl_esdhc_imx: add extra delay for IO voltage switch if necessary 
Some board like imx8mm-evkb, IO voltage switch from 3.3v to 1.8v need
around 18ms, common code only delay 10ms, so need to delay extra 8ms.
Otherwise voltage switch will timeout when wait for data0 line.

This IO voltage switch time depends on board design, depend on the
PMIC and capacitance. imx8mm-evkb board use PCA9450(PMIC) and 10uF
capacitance.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
2021-04-08 23:59:50 +02:00

1772 lines
45 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2007, 2010-2011 Freescale Semiconductor, Inc
* Copyright 2019 NXP Semiconductors
* Andy Fleming
* Yangbo Lu <yangbo.lu@nxp.com>
*
* Based vaguely on the pxa mmc code:
* (C) Copyright 2003
* Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
*/
#include <config.h>
#include <common.h>
#include <command.h>
#include <clk.h>
#include <cpu_func.h>
#include <errno.h>
#include <hwconfig.h>
#include <log.h>
#include <mmc.h>
#include <part.h>
#include <asm/cache.h>
#include <asm/global_data.h>
#include <dm/device_compat.h>
#include <linux/bitops.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <power/regulator.h>
#include <malloc.h>
#include <fsl_esdhc_imx.h>
#include <fdt_support.h>
#include <asm/io.h>
#include <dm.h>
#include <asm-generic/gpio.h>
#include <dm/pinctrl.h>
#include <dt-structs.h>
#include <mapmem.h>
#include <dm/ofnode.h>
#include <linux/iopoll.h>
#if !CONFIG_IS_ENABLED(BLK)
#include "mmc_private.h"
#endif
#ifndef ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE
#ifdef CONFIG_FSL_USDHC
#define ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE 1
#endif
#endif
DECLARE_GLOBAL_DATA_PTR;
#define SDHCI_IRQ_EN_BITS (IRQSTATEN_CC | IRQSTATEN_TC | \
IRQSTATEN_CINT | \
IRQSTATEN_CTOE | IRQSTATEN_CCE | IRQSTATEN_CEBE | \
IRQSTATEN_CIE | IRQSTATEN_DTOE | IRQSTATEN_DCE | \
IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR | \
IRQSTATEN_DINT)
#define MAX_TUNING_LOOP 40
#define ESDHC_DRIVER_STAGE_VALUE 0xffffffff
struct fsl_esdhc {
uint dsaddr; /* SDMA system address register */
uint blkattr; /* Block attributes register */
uint cmdarg; /* Command argument register */
uint xfertyp; /* Transfer type register */
uint cmdrsp0; /* Command response 0 register */
uint cmdrsp1; /* Command response 1 register */
uint cmdrsp2; /* Command response 2 register */
uint cmdrsp3; /* Command response 3 register */
uint datport; /* Buffer data port register */
uint prsstat; /* Present state register */
uint proctl; /* Protocol control register */
uint sysctl; /* System Control Register */
uint irqstat; /* Interrupt status register */
uint irqstaten; /* Interrupt status enable register */
uint irqsigen; /* Interrupt signal enable register */
uint autoc12err; /* Auto CMD error status register */
uint hostcapblt; /* Host controller capabilities register */
uint wml; /* Watermark level register */
uint mixctrl; /* For USDHC */
char reserved1[4]; /* reserved */
uint fevt; /* Force event register */
uint admaes; /* ADMA error status register */
uint adsaddr; /* ADMA system address register */
char reserved2[4];
uint dllctrl;
uint dllstat;
uint clktunectrlstatus;
char reserved3[4];
uint strobe_dllctrl;
uint strobe_dllstat;
char reserved4[72];
uint vendorspec;
uint mmcboot;
uint vendorspec2;
uint tuning_ctrl; /* on i.MX6/7/8/RT */
char reserved5[44];
uint hostver; /* Host controller version register */
char reserved6[4]; /* reserved */
uint dmaerraddr; /* DMA error address register */
char reserved7[4]; /* reserved */
uint dmaerrattr; /* DMA error attribute register */
char reserved8[4]; /* reserved */
uint hostcapblt2; /* Host controller capabilities register 2 */
char reserved9[8]; /* reserved */
uint tcr; /* Tuning control register */
char reserved10[28]; /* reserved */
uint sddirctl; /* SD direction control register */
char reserved11[712];/* reserved */
uint scr; /* eSDHC control register */
};
struct fsl_esdhc_plat {
#if CONFIG_IS_ENABLED(OF_PLATDATA)
/* Put this first since driver model will copy the data here */
struct dtd_fsl_esdhc dtplat;
#endif
struct mmc_config cfg;
struct mmc mmc;
};
struct esdhc_soc_data {
u32 flags;
};
/**
* struct fsl_esdhc_priv
*
* @esdhc_regs: registers of the sdhc controller
* @sdhc_clk: Current clk of the sdhc controller
* @bus_width: bus width, 1bit, 4bit or 8bit
* @cfg: mmc config
* @mmc: mmc
* Following is used when Driver Model is enabled for MMC
* @dev: pointer for the device
* @non_removable: 0: removable; 1: non-removable
* @broken_cd: 0: use GPIO for card detect; 1: Do not use GPIO for card detect
* @wp_enable: 1: enable checking wp; 0: no check
* @vs18_enable: 1: use 1.8V voltage; 0: use 3.3V
* @flags: ESDHC_FLAG_xx in include/fsl_esdhc_imx.h
* @caps: controller capabilities
* @tuning_step: tuning step setting in tuning_ctrl register
* @start_tuning_tap: the start point for tuning in tuning_ctrl register
* @strobe_dll_delay_target: settings in strobe_dllctrl
* @signal_voltage: indicating the current voltage
* @signal_voltage_switch_extra_delay_ms: extra delay for IO voltage switch
* @cd_gpio: gpio for card detection
* @wp_gpio: gpio for write protection
*/
struct fsl_esdhc_priv {
struct fsl_esdhc *esdhc_regs;
unsigned int sdhc_clk;
struct clk per_clk;
unsigned int clock;
unsigned int mode;
unsigned int bus_width;
#if !CONFIG_IS_ENABLED(BLK)
struct mmc *mmc;
#endif
struct udevice *dev;
int non_removable;
int broken_cd;
int wp_enable;
int vs18_enable;
u32 flags;
u32 caps;
u32 tuning_step;
u32 tuning_start_tap;
u32 strobe_dll_delay_target;
u32 signal_voltage;
u32 signal_voltage_switch_extra_delay_ms;
#if CONFIG_IS_ENABLED(DM_REGULATOR)
struct udevice *vqmmc_dev;
struct udevice *vmmc_dev;
#endif
#if CONFIG_IS_ENABLED(DM_GPIO)
struct gpio_desc cd_gpio;
struct gpio_desc wp_gpio;
#endif
};
/* Return the XFERTYP flags for a given command and data packet */
static uint esdhc_xfertyp(struct mmc_cmd *cmd, struct mmc_data *data)
{
uint xfertyp = 0;
if (data) {
xfertyp |= XFERTYP_DPSEL;
#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
xfertyp |= XFERTYP_DMAEN;
#endif
if (data->blocks > 1) {
xfertyp |= XFERTYP_MSBSEL;
xfertyp |= XFERTYP_BCEN;
#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111
xfertyp |= XFERTYP_AC12EN;
#endif
}
if (data->flags & MMC_DATA_READ)
xfertyp |= XFERTYP_DTDSEL;
}
if (cmd->resp_type & MMC_RSP_CRC)
xfertyp |= XFERTYP_CCCEN;
if (cmd->resp_type & MMC_RSP_OPCODE)
xfertyp |= XFERTYP_CICEN;
if (cmd->resp_type & MMC_RSP_136)
xfertyp |= XFERTYP_RSPTYP_136;
else if (cmd->resp_type & MMC_RSP_BUSY)
xfertyp |= XFERTYP_RSPTYP_48_BUSY;
else if (cmd->resp_type & MMC_RSP_PRESENT)
xfertyp |= XFERTYP_RSPTYP_48;
if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
xfertyp |= XFERTYP_CMDTYP_ABORT;
return XFERTYP_CMD(cmd->cmdidx) | xfertyp;
}
#ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO
/*
* PIO Read/Write Mode reduce the performace as DMA is not used in this mode.
*/
static void esdhc_pio_read_write(struct fsl_esdhc_priv *priv,
struct mmc_data *data)
{
struct fsl_esdhc *regs = priv->esdhc_regs;
uint blocks;
char *buffer;
uint databuf;
uint size;
uint irqstat;
ulong start;
if (data->flags & MMC_DATA_READ) {
blocks = data->blocks;
buffer = data->dest;
while (blocks) {
start = get_timer(0);
size = data->blocksize;
irqstat = esdhc_read32(&regs->irqstat);
while (!(esdhc_read32(&regs->prsstat) & PRSSTAT_BREN)) {
if (get_timer(start) > PIO_TIMEOUT) {
printf("\nData Read Failed in PIO Mode.");
return;
}
}
while (size && (!(irqstat & IRQSTAT_TC))) {
udelay(100); /* Wait before last byte transfer complete */
irqstat = esdhc_read32(&regs->irqstat);
databuf = in_le32(&regs->datport);
*((uint *)buffer) = databuf;
buffer += 4;
size -= 4;
}
blocks--;
}
} else {
blocks = data->blocks;
buffer = (char *)data->src;
while (blocks) {
start = get_timer(0);
size = data->blocksize;
irqstat = esdhc_read32(&regs->irqstat);
while (!(esdhc_read32(&regs->prsstat) & PRSSTAT_BWEN)) {
if (get_timer(start) > PIO_TIMEOUT) {
printf("\nData Write Failed in PIO Mode.");
return;
}
}
while (size && (!(irqstat & IRQSTAT_TC))) {
udelay(100); /* Wait before last byte transfer complete */
databuf = *((uint *)buffer);
buffer += 4;
size -= 4;
irqstat = esdhc_read32(&regs->irqstat);
out_le32(&regs->datport, databuf);
}
blocks--;
}
}
}
#endif
static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc,
struct mmc_data *data)
{
int timeout;
struct fsl_esdhc *regs = priv->esdhc_regs;
#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
dma_addr_t addr;
#endif
uint wml_value;
wml_value = data->blocksize/4;
if (data->flags & MMC_DATA_READ) {
if (wml_value > WML_RD_WML_MAX)
wml_value = WML_RD_WML_MAX_VAL;
esdhc_clrsetbits32(&regs->wml, WML_RD_WML_MASK, wml_value);
#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
addr = virt_to_phys((void *)(data->dest));
if (upper_32_bits(addr))
printf("Error found for upper 32 bits\n");
else
esdhc_write32(&regs->dsaddr, lower_32_bits(addr));
#else
esdhc_write32(&regs->dsaddr, (u32)data->dest);
#endif
#endif
} else {
#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
flush_dcache_range((ulong)data->src,
(ulong)data->src+data->blocks
*data->blocksize);
#endif
if (wml_value > WML_WR_WML_MAX)
wml_value = WML_WR_WML_MAX_VAL;
if (priv->wp_enable) {
if ((esdhc_read32(&regs->prsstat) &
PRSSTAT_WPSPL) == 0) {
printf("\nThe SD card is locked. Can not write to a locked card.\n\n");
return -ETIMEDOUT;
}
} else {
#if CONFIG_IS_ENABLED(DM_GPIO)
if (dm_gpio_is_valid(&priv->wp_gpio) &&
dm_gpio_get_value(&priv->wp_gpio)) {
printf("\nThe SD card is locked. Can not write to a locked card.\n\n");
return -ETIMEDOUT;
}
#endif
}
esdhc_clrsetbits32(&regs->wml, WML_WR_WML_MASK,
wml_value << 16);
#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
addr = virt_to_phys((void *)(data->src));
if (upper_32_bits(addr))
printf("Error found for upper 32 bits\n");
else
esdhc_write32(&regs->dsaddr, lower_32_bits(addr));
#else
esdhc_write32(&regs->dsaddr, (u32)data->src);
#endif
#endif
}
esdhc_write32(&regs->blkattr, data->blocks << 16 | data->blocksize);
/* Calculate the timeout period for data transactions */
/*
* 1)Timeout period = (2^(timeout+13)) SD Clock cycles
* 2)Timeout period should be minimum 0.250sec as per SD Card spec
* So, Number of SD Clock cycles for 0.25sec should be minimum
* (SD Clock/sec * 0.25 sec) SD Clock cycles
* = (mmc->clock * 1/4) SD Clock cycles
* As 1) >= 2)
* => (2^(timeout+13)) >= mmc->clock * 1/4
* Taking log2 both the sides
* => timeout + 13 >= log2(mmc->clock/4)
* Rounding up to next power of 2
* => timeout + 13 = log2(mmc->clock/4) + 1
* => timeout + 13 = fls(mmc->clock/4)
*
* However, the MMC spec "It is strongly recommended for hosts to
* implement more than 500ms timeout value even if the card
* indicates the 250ms maximum busy length." Even the previous
* value of 300ms is known to be insufficient for some cards.
* So, we use
* => timeout + 13 = fls(mmc->clock/2)
*/
timeout = fls(mmc->clock/2);
timeout -= 13;
if (timeout > 14)
timeout = 14;
if (timeout < 0)
timeout = 0;
#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC_A001
if ((timeout == 4) || (timeout == 8) || (timeout == 12))
timeout++;
#endif
#ifdef ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE
timeout = 0xE;
#endif
esdhc_clrsetbits32(&regs->sysctl, SYSCTL_TIMEOUT_MASK, timeout << 16);
return 0;
}
static void check_and_invalidate_dcache_range
(struct mmc_cmd *cmd,
struct mmc_data *data) {
unsigned start = 0;
unsigned end = 0;
unsigned size = roundup(ARCH_DMA_MINALIGN,
data->blocks*data->blocksize);
#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
dma_addr_t addr;
addr = virt_to_phys((void *)(data->dest));
if (upper_32_bits(addr))
printf("Error found for upper 32 bits\n");
else
start = lower_32_bits(addr);
#else
start = (unsigned)data->dest;
#endif
end = start + size;
invalidate_dcache_range(start, end);
}
#ifdef CONFIG_MCF5441x
/*
* Swaps 32-bit words to little-endian byte order.
*/
static inline void sd_swap_dma_buff(struct mmc_data *data)
{
int i, size = data->blocksize >> 2;
u32 *buffer = (u32 *)data->dest;
u32 sw;
while (data->blocks--) {
for (i = 0; i < size; i++) {
sw = __sw32(*buffer);
*buffer++ = sw;
}
}
}
#endif
/*
* Sends a command out on the bus. Takes the mmc pointer,
* a command pointer, and an optional data pointer.
*/
static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
struct mmc_cmd *cmd, struct mmc_data *data)
{
int err = 0;
uint xfertyp;
uint irqstat;
u32 flags = IRQSTAT_CC | IRQSTAT_CTOE;
struct fsl_esdhc *regs = priv->esdhc_regs;
unsigned long start;
#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111
if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
return 0;
#endif
esdhc_write32(&regs->irqstat, -1);
sync();
/* Wait for the bus to be idle */
while ((esdhc_read32(&regs->prsstat) & PRSSTAT_CICHB) ||
(esdhc_read32(&regs->prsstat) & PRSSTAT_CIDHB))
;
while (esdhc_read32(&regs->prsstat) & PRSSTAT_DLA)
;
/* Set up for a data transfer if we have one */
if (data) {
err = esdhc_setup_data(priv, mmc, data);
if(err)
return err;
if (data->flags & MMC_DATA_READ)
check_and_invalidate_dcache_range(cmd, data);
}
/* Figure out the transfer arguments */
xfertyp = esdhc_xfertyp(cmd, data);
/* Mask all irqs */
esdhc_write32(&regs->irqsigen, 0);
/* Send the command */
esdhc_write32(&regs->cmdarg, cmd->cmdarg);
#if defined(CONFIG_FSL_USDHC)
esdhc_write32(&regs->mixctrl,
(esdhc_read32(&regs->mixctrl) & 0xFFFFFF80) | (xfertyp & 0x7F)
| (mmc->ddr_mode ? XFERTYP_DDREN : 0));
esdhc_write32(&regs->xfertyp, xfertyp & 0xFFFF0000);
#else
esdhc_write32(&regs->xfertyp, xfertyp);
#endif
if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) ||
(cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200))
flags = IRQSTAT_BRR;
/* Wait for the command to complete */
start = get_timer(0);
while (!(esdhc_read32(&regs->irqstat) & flags)) {
if (get_timer(start) > 1000) {
err = -ETIMEDOUT;
goto out;
}
}
irqstat = esdhc_read32(&regs->irqstat);
if (irqstat & CMD_ERR) {
err = -ECOMM;
goto out;
}
if (irqstat & IRQSTAT_CTOE) {
err = -ETIMEDOUT;
goto out;
}
/* Workaround for ESDHC errata ENGcm03648 */
if (!data && (cmd->resp_type & MMC_RSP_BUSY)) {
int timeout = 50000;
/* Poll on DATA0 line for cmd with busy signal for 5000 ms */
while (timeout > 0 && !(esdhc_read32(&regs->prsstat) &
PRSSTAT_DAT0)) {
udelay(100);
timeout--;
}
if (timeout <= 0) {
printf("Timeout waiting for DAT0 to go high!\n");
err = -ETIMEDOUT;
goto out;
}
}
/* Copy the response to the response buffer */
if (cmd->resp_type & MMC_RSP_136) {
u32 cmdrsp3, cmdrsp2, cmdrsp1, cmdrsp0;
cmdrsp3 = esdhc_read32(&regs->cmdrsp3);
cmdrsp2 = esdhc_read32(&regs->cmdrsp2);
cmdrsp1 = esdhc_read32(&regs->cmdrsp1);
cmdrsp0 = esdhc_read32(&regs->cmdrsp0);
cmd->response[0] = (cmdrsp3 << 8) | (cmdrsp2 >> 24);
cmd->response[1] = (cmdrsp2 << 8) | (cmdrsp1 >> 24);
cmd->response[2] = (cmdrsp1 << 8) | (cmdrsp0 >> 24);
cmd->response[3] = (cmdrsp0 << 8);
} else
cmd->response[0] = esdhc_read32(&regs->cmdrsp0);
/* Wait until all of the blocks are transferred */
if (data) {
#ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO
esdhc_pio_read_write(priv, data);
#else
flags = DATA_COMPLETE;
if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) ||
(cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200)) {
flags = IRQSTAT_BRR;
}
do {
irqstat = esdhc_read32(&regs->irqstat);
if (irqstat & IRQSTAT_DTOE) {
err = -ETIMEDOUT;
goto out;
}
if (irqstat & DATA_ERR) {
err = -ECOMM;
goto out;
}
} while ((irqstat & flags) != flags);
/*
* Need invalidate the dcache here again to avoid any
* cache-fill during the DMA operations such as the
* speculative pre-fetching etc.
*/
if (data->flags & MMC_DATA_READ) {
check_and_invalidate_dcache_range(cmd, data);
#ifdef CONFIG_MCF5441x
sd_swap_dma_buff(data);
#endif
}
#endif
}
out:
/* Reset CMD and DATA portions on error */
if (err) {
esdhc_write32(&regs->sysctl, esdhc_read32(&regs->sysctl) |
SYSCTL_RSTC);
while (esdhc_read32(&regs->sysctl) & SYSCTL_RSTC)
;
if (data) {
esdhc_write32(&regs->sysctl,
esdhc_read32(&regs->sysctl) |
SYSCTL_RSTD);
while ((esdhc_read32(&regs->sysctl) & SYSCTL_RSTD))
;
}
/* If this was CMD11, then notify that power cycle is needed */
if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V)
printf("CMD11 to switch to 1.8V mode failed, card requires power cycle.\n");
}
esdhc_write32(&regs->irqstat, -1);
return err;
}
static void set_sysctl(struct fsl_esdhc_priv *priv, struct mmc *mmc, uint clock)
{
struct fsl_esdhc *regs = priv->esdhc_regs;
int div = 1;
u32 tmp;
int ret;
#ifdef ARCH_MXC
#ifdef CONFIG_MX53
/* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
int pre_div = (regs == (struct fsl_esdhc *)MMC_SDHC3_BASE_ADDR) ? 2 : 1;
#else
int pre_div = 1;
#endif
#else
int pre_div = 2;
#endif
int ddr_pre_div = mmc->ddr_mode ? 2 : 1;
int sdhc_clk = priv->sdhc_clk;
uint clk;
while (sdhc_clk / (16 * pre_div * ddr_pre_div) > clock && pre_div < 256)
pre_div *= 2;
while (sdhc_clk / (div * pre_div * ddr_pre_div) > clock && div < 16)
div++;
pre_div >>= 1;
div -= 1;
clk = (pre_div << 8) | (div << 4);
#ifdef CONFIG_FSL_USDHC
esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON);
ret = readx_poll_timeout(esdhc_read32, &regs->prsstat, tmp, tmp & PRSSTAT_SDOFF, 100);
if (ret)
pr_warn("fsl_esdhc_imx: Internal clock never gate off.\n");
#else
esdhc_clrbits32(&regs->sysctl, SYSCTL_CKEN);
#endif
esdhc_clrsetbits32(&regs->sysctl, SYSCTL_CLOCK_MASK, clk);
ret = readx_poll_timeout(esdhc_read32, &regs->prsstat, tmp, tmp & PRSSTAT_SDSTB, 100);
if (ret)
pr_warn("fsl_esdhc_imx: Internal clock never stabilised.\n");
#ifdef CONFIG_FSL_USDHC
esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON);
#else
esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
#endif
priv->clock = clock;
}
#ifdef MMC_SUPPORTS_TUNING
static int esdhc_change_pinstate(struct udevice *dev)
{
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
int ret;
switch (priv->mode) {
case UHS_SDR50:
case UHS_DDR50:
ret = pinctrl_select_state(dev, "state_100mhz");
break;
case UHS_SDR104:
case MMC_HS_200:
case MMC_HS_400:
case MMC_HS_400_ES:
ret = pinctrl_select_state(dev, "state_200mhz");
break;
default:
ret = pinctrl_select_state(dev, "default");
break;
}
if (ret)
printf("%s %d error\n", __func__, priv->mode);
return ret;
}
static void esdhc_reset_tuning(struct mmc *mmc)
{
struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
struct fsl_esdhc *regs = priv->esdhc_regs;
if (priv->flags & ESDHC_FLAG_USDHC) {
if (priv->flags & ESDHC_FLAG_STD_TUNING) {
esdhc_clrbits32(&regs->autoc12err,
MIX_CTRL_SMPCLK_SEL |
MIX_CTRL_EXE_TUNE);
}
}
}
static void esdhc_set_strobe_dll(struct mmc *mmc)
{
struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
struct fsl_esdhc *regs = priv->esdhc_regs;
u32 val;
u32 tmp;
int ret;
if (priv->clock > ESDHC_STROBE_DLL_CLK_FREQ) {
esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON);
ret = readx_poll_timeout(esdhc_read32, &regs->prsstat, tmp, tmp & PRSSTAT_SDOFF, 100);
if (ret)
pr_warn("fsl_esdhc_imx: Internal clock never gate off.\n");
esdhc_write32(&regs->strobe_dllctrl, ESDHC_STROBE_DLL_CTRL_RESET);
/*
* enable strobe dll ctrl and adjust the delay target
* for the uSDHC loopback read clock
*/
val = ESDHC_STROBE_DLL_CTRL_ENABLE |
(priv->strobe_dll_delay_target <<
ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
esdhc_write32(&regs->strobe_dllctrl, val);
/* wait 1us to make sure strobe dll status register stable */
mdelay(1);
val = esdhc_read32(&regs->strobe_dllstat);
if (!(val & ESDHC_STROBE_DLL_STS_REF_LOCK))
pr_warn("HS400 strobe DLL status REF not lock!\n");
if (!(val & ESDHC_STROBE_DLL_STS_SLV_LOCK))
pr_warn("HS400 strobe DLL status SLV not lock!\n");
esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON);
}
}
static int esdhc_set_timing(struct mmc *mmc)
{
struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
struct fsl_esdhc *regs = priv->esdhc_regs;
u32 mixctrl;
mixctrl = esdhc_read32(&regs->mixctrl);
mixctrl &= ~(MIX_CTRL_DDREN | MIX_CTRL_HS400_EN);
switch (mmc->selected_mode) {
case MMC_LEGACY:
esdhc_reset_tuning(mmc);
esdhc_write32(&regs->mixctrl, mixctrl);
break;
case MMC_HS_400:
case MMC_HS_400_ES:
mixctrl |= MIX_CTRL_DDREN | MIX_CTRL_HS400_EN;
esdhc_write32(&regs->mixctrl, mixctrl);
break;
case MMC_HS:
case MMC_HS_52:
case MMC_HS_200:
case SD_HS:
case UHS_SDR12:
case UHS_SDR25:
case UHS_SDR50:
case UHS_SDR104:
esdhc_write32(&regs->mixctrl, mixctrl);
break;
case UHS_DDR50:
case MMC_DDR_52:
mixctrl |= MIX_CTRL_DDREN;
esdhc_write32(&regs->mixctrl, mixctrl);
break;
default:
printf("Not supported %d\n", mmc->selected_mode);
return -EINVAL;
}
priv->mode = mmc->selected_mode;
return esdhc_change_pinstate(mmc->dev);
}
static int esdhc_set_voltage(struct mmc *mmc)
{
struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
struct fsl_esdhc *regs = priv->esdhc_regs;
#if CONFIG_IS_ENABLED(DM_REGULATOR)
int ret;
#endif
priv->signal_voltage = mmc->signal_voltage;
switch (mmc->signal_voltage) {
case MMC_SIGNAL_VOLTAGE_330:
if (priv->vs18_enable)
return -ENOTSUPP;
#if CONFIG_IS_ENABLED(DM_REGULATOR)
if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) {
ret = regulator_set_value(priv->vqmmc_dev, 3300000);
if (ret) {
printf("Setting to 3.3V error");
return -EIO;
}
/* Wait for 5ms */
mdelay(5);
}
#endif
esdhc_clrbits32(&regs->vendorspec, ESDHC_VENDORSPEC_VSELECT);
if (!(esdhc_read32(&regs->vendorspec) &
ESDHC_VENDORSPEC_VSELECT))
return 0;
return -EAGAIN;
case MMC_SIGNAL_VOLTAGE_180:
#if CONFIG_IS_ENABLED(DM_REGULATOR)
if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) {
ret = regulator_set_value(priv->vqmmc_dev, 1800000);
if (ret) {
printf("Setting to 1.8V error");
return -EIO;
}
}
#endif
esdhc_setbits32(&regs->vendorspec, ESDHC_VENDORSPEC_VSELECT);
/*
* some board like imx8mm-evk need about 18ms to switch
* the IO voltage from 3.3v to 1.8v, common code only
* delay 10ms, so need to delay extra time to make sure
* the IO voltage change to 1.8v.
*/
if (priv->signal_voltage_switch_extra_delay_ms)
mdelay(priv->signal_voltage_switch_extra_delay_ms);
if (esdhc_read32(&regs->vendorspec) & ESDHC_VENDORSPEC_VSELECT)
return 0;
return -EAGAIN;
case MMC_SIGNAL_VOLTAGE_120:
return -ENOTSUPP;
default:
return 0;
}
}
static void esdhc_stop_tuning(struct mmc *mmc)
{
struct mmc_cmd cmd;
cmd.cmdidx = MMC_CMD_STOP_TRANSMISSION;
cmd.cmdarg = 0;
cmd.resp_type = MMC_RSP_R1b;
dm_mmc_send_cmd(mmc->dev, &cmd, NULL);
}
static int fsl_esdhc_execute_tuning(struct udevice *dev, uint32_t opcode)
{
struct fsl_esdhc_plat *plat = dev_get_plat(dev);
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
struct fsl_esdhc *regs = priv->esdhc_regs;
struct mmc *mmc = &plat->mmc;
u32 irqstaten = esdhc_read32(&regs->irqstaten);
u32 irqsigen = esdhc_read32(&regs->irqsigen);
int i, ret = -ETIMEDOUT;
u32 val, mixctrl;
/* clock tuning is not needed for upto 52MHz */
if (mmc->clock <= 52000000)
return 0;
/* This is readw/writew SDHCI_HOST_CONTROL2 when tuning */
if (priv->flags & ESDHC_FLAG_STD_TUNING) {
val = esdhc_read32(&regs->autoc12err);
mixctrl = esdhc_read32(&regs->mixctrl);
val &= ~MIX_CTRL_SMPCLK_SEL;
mixctrl &= ~(MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN);
val |= MIX_CTRL_EXE_TUNE;
mixctrl |= MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN;
esdhc_write32(&regs->autoc12err, val);
esdhc_write32(&regs->mixctrl, mixctrl);
}
/* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE); */
mixctrl = esdhc_read32(&regs->mixctrl);
mixctrl = MIX_CTRL_DTDSEL_READ | (mixctrl & ~MIX_CTRL_SDHCI_MASK);
esdhc_write32(&regs->mixctrl, mixctrl);
esdhc_write32(&regs->irqstaten, IRQSTATEN_BRR);
esdhc_write32(&regs->irqsigen, IRQSTATEN_BRR);
/*
* Issue opcode repeatedly till Execute Tuning is set to 0 or the number
* of loops reaches 40 times.
*/
for (i = 0; i < MAX_TUNING_LOOP; i++) {
u32 ctrl;
if (opcode == MMC_CMD_SEND_TUNING_BLOCK_HS200) {
if (mmc->bus_width == 8)
esdhc_write32(&regs->blkattr, 0x7080);
else if (mmc->bus_width == 4)
esdhc_write32(&regs->blkattr, 0x7040);
} else {
esdhc_write32(&regs->blkattr, 0x7040);
}
/* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE) */
val = esdhc_read32(&regs->mixctrl);
val = MIX_CTRL_DTDSEL_READ | (val & ~MIX_CTRL_SDHCI_MASK);
esdhc_write32(&regs->mixctrl, val);
/* We are using STD tuning, no need to check return value */
mmc_send_tuning(mmc, opcode, NULL);
ctrl = esdhc_read32(&regs->autoc12err);
if ((!(ctrl & MIX_CTRL_EXE_TUNE)) &&
(ctrl & MIX_CTRL_SMPCLK_SEL)) {
ret = 0;
break;
}
}
esdhc_write32(&regs->irqstaten, irqstaten);
esdhc_write32(&regs->irqsigen, irqsigen);
esdhc_stop_tuning(mmc);
return ret;
}
#endif
static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
{
struct fsl_esdhc *regs = priv->esdhc_regs;
int ret __maybe_unused;
u32 clock;
#ifdef MMC_SUPPORTS_TUNING
/*
* call esdhc_set_timing() before update the clock rate,
* This is because current we support DDR and SDR mode,
* Once the DDR_EN bit is set, the card clock will be
* divide by 2 automatically. So need to do this before
* setting clock rate.
*/
if (priv->mode != mmc->selected_mode) {
ret = esdhc_set_timing(mmc);
if (ret) {
printf("esdhc_set_timing error %d\n", ret);
return ret;
}
}
#endif
/* Set the clock speed */
clock = mmc->clock;
if (clock < mmc->cfg->f_min)
clock = mmc->cfg->f_min;
if (priv->clock != clock)
set_sysctl(priv, mmc, clock);
#ifdef MMC_SUPPORTS_TUNING
if (mmc->clk_disable) {
#ifdef CONFIG_FSL_USDHC
u32 tmp;
esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON);
ret = readx_poll_timeout(esdhc_read32, &regs->prsstat, tmp, tmp & PRSSTAT_SDOFF, 100);
if (ret)
pr_warn("fsl_esdhc_imx: Internal clock never gate off.\n");
#else
esdhc_clrbits32(&regs->sysctl, SYSCTL_CKEN);
#endif
} else {
#ifdef CONFIG_FSL_USDHC
esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON);
#else
esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
#endif
}
/*
* For HS400/HS400ES mode, make sure set the strobe dll in the
* target clock rate. So call esdhc_set_strobe_dll() after the
* clock updated.
*/
if (mmc->selected_mode == MMC_HS_400 || mmc->selected_mode == MMC_HS_400_ES)
esdhc_set_strobe_dll(mmc);
if (priv->signal_voltage != mmc->signal_voltage) {
ret = esdhc_set_voltage(mmc);
if (ret) {
if (ret != -ENOTSUPP)
printf("esdhc_set_voltage error %d\n", ret);
return ret;
}
}
#endif
/* Set the bus width */
esdhc_clrbits32(&regs->proctl, PROCTL_DTW_4 | PROCTL_DTW_8);
if (mmc->bus_width == 4)
esdhc_setbits32(&regs->proctl, PROCTL_DTW_4);
else if (mmc->bus_width == 8)
esdhc_setbits32(&regs->proctl, PROCTL_DTW_8);
return 0;
}
static int esdhc_init_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
{
struct fsl_esdhc *regs = priv->esdhc_regs;
ulong start;
/* Reset the entire host controller */
esdhc_setbits32(&regs->sysctl, SYSCTL_RSTA);
/* Wait until the controller is available */
start = get_timer(0);
while ((esdhc_read32(&regs->sysctl) & SYSCTL_RSTA)) {
if (get_timer(start) > 1000)
return -ETIMEDOUT;
}
#if defined(CONFIG_FSL_USDHC)
/* RSTA doesn't reset MMC_BOOT register, so manually reset it */
esdhc_write32(&regs->mmcboot, 0x0);
/* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */
esdhc_write32(&regs->mixctrl, 0x0);
esdhc_write32(&regs->clktunectrlstatus, 0x0);
/* Put VEND_SPEC to default value */
if (priv->vs18_enable)
esdhc_write32(&regs->vendorspec, (VENDORSPEC_INIT |
ESDHC_VENDORSPEC_VSELECT));
else
esdhc_write32(&regs->vendorspec, VENDORSPEC_INIT);
/* Disable DLL_CTRL delay line */
esdhc_write32(&regs->dllctrl, 0x0);
#endif
#ifndef ARCH_MXC
/* Enable cache snooping */
esdhc_write32(&regs->scr, 0x00000040);
#endif
#ifndef CONFIG_FSL_USDHC
esdhc_setbits32(&regs->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN);
#else
esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON);
#endif
/* Set the initial clock speed */
mmc_set_clock(mmc, 400000, MMC_CLK_ENABLE);
/* Disable the BRR and BWR bits in IRQSTAT */
esdhc_clrbits32(&regs->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR);
#ifdef CONFIG_MCF5441x
esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
#else
/* Put the PROCTL reg back to the default */
esdhc_write32(&regs->proctl, PROCTL_INIT);
#endif
/* Set timout to the maximum value */
esdhc_clrsetbits32(&regs->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16);
return 0;
}
static int esdhc_getcd_common(struct fsl_esdhc_priv *priv)
{
struct fsl_esdhc *regs = priv->esdhc_regs;
int timeout = 1000;
#ifdef CONFIG_ESDHC_DETECT_QUIRK
if (CONFIG_ESDHC_DETECT_QUIRK)
return 1;
#endif
#if CONFIG_IS_ENABLED(DM_MMC)
if (priv->non_removable)
return 1;
if (priv->broken_cd)
return 1;
#if CONFIG_IS_ENABLED(DM_GPIO)
if (dm_gpio_is_valid(&priv->cd_gpio))
return dm_gpio_get_value(&priv->cd_gpio);
#endif
#endif
while (!(esdhc_read32(&regs->prsstat) & PRSSTAT_CINS) && --timeout)
udelay(1000);
return timeout > 0;
}
static int esdhc_reset(struct fsl_esdhc *regs)
{
ulong start;
/* reset the controller */
esdhc_setbits32(&regs->sysctl, SYSCTL_RSTA);
/* hardware clears the bit when it is done */
start = get_timer(0);
while ((esdhc_read32(&regs->sysctl) & SYSCTL_RSTA)) {
if (get_timer(start) > 100) {
printf("MMC/SD: Reset never completed.\n");
return -ETIMEDOUT;
}
}
return 0;
}
#if !CONFIG_IS_ENABLED(DM_MMC)
static int esdhc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_priv *priv = mmc->priv;
return esdhc_getcd_common(priv);
}
static int esdhc_init(struct mmc *mmc)
{
struct fsl_esdhc_priv *priv = mmc->priv;
return esdhc_init_common(priv, mmc);
}
static int esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
struct mmc_data *data)
{
struct fsl_esdhc_priv *priv = mmc->priv;
return esdhc_send_cmd_common(priv, mmc, cmd, data);
}
static int esdhc_set_ios(struct mmc *mmc)
{
struct fsl_esdhc_priv *priv = mmc->priv;
return esdhc_set_ios_common(priv, mmc);
}
static const struct mmc_ops esdhc_ops = {
.getcd = esdhc_getcd,
.init = esdhc_init,
.send_cmd = esdhc_send_cmd,
.set_ios = esdhc_set_ios,
};
#endif
static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
struct fsl_esdhc_plat *plat)
{
struct mmc_config *cfg;
struct fsl_esdhc *regs;
u32 caps, voltage_caps;
int ret;
if (!priv)
return -EINVAL;
regs = priv->esdhc_regs;
/* First reset the eSDHC controller */
ret = esdhc_reset(regs);
if (ret)
return ret;
#ifdef CONFIG_MCF5441x
/* ColdFire, using SDHC_DATA[3] for card detection */
esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
#endif
#ifndef CONFIG_FSL_USDHC
esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
| SYSCTL_IPGEN | SYSCTL_CKEN);
/* Clearing tuning bits in case ROM has set it already */
esdhc_write32(&regs->mixctrl, 0);
esdhc_write32(&regs->autoc12err, 0);
esdhc_write32(&regs->clktunectrlstatus, 0);
#else
esdhc_setbits32(&regs->vendorspec, VENDORSPEC_FRC_SDCLK_ON);
#endif
if (priv->vs18_enable)
esdhc_setbits32(&regs->vendorspec, ESDHC_VENDORSPEC_VSELECT);
esdhc_write32(&regs->irqstaten, SDHCI_IRQ_EN_BITS);
cfg = &plat->cfg;
#ifndef CONFIG_DM_MMC
memset(cfg, '\0', sizeof(*cfg));
#endif
voltage_caps = 0;
caps = esdhc_read32(&regs->hostcapblt);
#ifdef CONFIG_MCF5441x
/*
* MCF5441x RM declares in more points that sdhc clock speed must
* never exceed 25 Mhz. From this, the HS bit needs to be disabled
* from host capabilities.
*/
caps &= ~ESDHC_HOSTCAPBLT_HSS;
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135
caps = caps & ~(ESDHC_HOSTCAPBLT_SRS |
ESDHC_HOSTCAPBLT_VS18 | ESDHC_HOSTCAPBLT_VS30);
#endif
/* T4240 host controller capabilities register should have VS33 bit */
#ifdef CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
caps = caps | ESDHC_HOSTCAPBLT_VS33;
#endif
if (caps & ESDHC_HOSTCAPBLT_VS18)
voltage_caps |= MMC_VDD_165_195;
if (caps & ESDHC_HOSTCAPBLT_VS30)
voltage_caps |= MMC_VDD_29_30 | MMC_VDD_30_31;
if (caps & ESDHC_HOSTCAPBLT_VS33)
voltage_caps |= MMC_VDD_32_33 | MMC_VDD_33_34;
cfg->name = "FSL_SDHC";
#if !CONFIG_IS_ENABLED(DM_MMC)
cfg->ops = &esdhc_ops;
#endif
#ifdef CONFIG_SYS_SD_VOLTAGE
cfg->voltages = CONFIG_SYS_SD_VOLTAGE;
#else
cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
#endif
if ((cfg->voltages & voltage_caps) == 0) {
printf("voltage not supported by controller\n");
return -1;
}
if (priv->bus_width == 8)
cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
else if (priv->bus_width == 4)
cfg->host_caps = MMC_MODE_4BIT;
cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
#ifdef CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
cfg->host_caps |= MMC_MODE_DDR_52MHz;
#endif
if (priv->bus_width > 0) {
if (priv->bus_width < 8)
cfg->host_caps &= ~MMC_MODE_8BIT;
if (priv->bus_width < 4)
cfg->host_caps &= ~MMC_MODE_4BIT;
}
if (caps & ESDHC_HOSTCAPBLT_HSS)
cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
#ifdef CONFIG_ESDHC_DETECT_8_BIT_QUIRK
if (CONFIG_ESDHC_DETECT_8_BIT_QUIRK)
cfg->host_caps &= ~MMC_MODE_8BIT;
#endif
cfg->host_caps |= priv->caps;
cfg->f_min = 400000;
cfg->f_max = min(priv->sdhc_clk, (u32)200000000);
cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
esdhc_write32(&regs->dllctrl, 0);
if (priv->flags & ESDHC_FLAG_USDHC) {
if (priv->flags & ESDHC_FLAG_STD_TUNING) {
u32 val = esdhc_read32(&regs->tuning_ctrl);
val |= ESDHC_STD_TUNING_EN;
val &= ~ESDHC_TUNING_START_TAP_MASK;
val |= priv->tuning_start_tap;
val &= ~ESDHC_TUNING_STEP_MASK;
val |= (priv->tuning_step) << ESDHC_TUNING_STEP_SHIFT;
/* Disable the CMD CRC check for tuning, if not, need to
* add some delay after every tuning command, because
* hardware standard tuning logic will directly go to next
* step once it detect the CMD CRC error, will not wait for
* the card side to finally send out the tuning data, trigger
* the buffer read ready interrupt immediately. If usdhc send
* the next tuning command some eMMC card will stuck, can't
* response, block the tuning procedure or the first command
* after the whole tuning procedure always can't get any response.
*/
val |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE;
esdhc_write32(&regs->tuning_ctrl, val);
}
}
return 0;
}
#if !CONFIG_IS_ENABLED(DM_MMC)
static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg,
struct fsl_esdhc_priv *priv)
{
if (!cfg || !priv)
return -EINVAL;
priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base);
priv->bus_width = cfg->max_bus_width;
priv->sdhc_clk = cfg->sdhc_clk;
priv->wp_enable = cfg->wp_enable;
priv->vs18_enable = cfg->vs18_enable;
return 0;
};
int fsl_esdhc_initialize(struct bd_info *bis, struct fsl_esdhc_cfg *cfg)
{
struct fsl_esdhc_plat *plat;
struct fsl_esdhc_priv *priv;
struct mmc *mmc;
int ret;
if (!cfg)
return -EINVAL;
priv = calloc(sizeof(struct fsl_esdhc_priv), 1);
if (!priv)
return -ENOMEM;
plat = calloc(sizeof(struct fsl_esdhc_plat), 1);
if (!plat) {
free(priv);
return -ENOMEM;
}
ret = fsl_esdhc_cfg_to_priv(cfg, priv);
if (ret) {
debug("%s xlate failure\n", __func__);
free(plat);
free(priv);
return ret;
}
ret = fsl_esdhc_init(priv, plat);
if (ret) {
debug("%s init failure\n", __func__);
free(plat);
free(priv);
return ret;
}
mmc = mmc_create(&plat->cfg, priv);
if (!mmc)
return -EIO;
priv->mmc = mmc;
return 0;
}
int fsl_esdhc_mmc_init(struct bd_info *bis)
{
struct fsl_esdhc_cfg *cfg;
cfg = calloc(sizeof(struct fsl_esdhc_cfg), 1);
cfg->esdhc_base = CONFIG_SYS_FSL_ESDHC_ADDR;
cfg->sdhc_clk = gd->arch.sdhc_clk;
return fsl_esdhc_initialize(bis, cfg);
}
#endif
#ifdef CONFIG_OF_LIBFDT
__weak int esdhc_status_fixup(void *blob, const char *compat)
{
#ifdef CONFIG_FSL_ESDHC_PIN_MUX
if (!hwconfig("esdhc")) {
do_fixup_by_compat(blob, compat, "status", "disabled",
sizeof("disabled"), 1);
return 1;
}
#endif
return 0;
}
void fdt_fixup_esdhc(void *blob, struct bd_info *bd)
{
const char *compat = "fsl,esdhc";
if (esdhc_status_fixup(blob, compat))
return;
do_fixup_by_compat_u32(blob, compat, "clock-frequency",
gd->arch.sdhc_clk, 1);
}
#endif
#if CONFIG_IS_ENABLED(DM_MMC)
#include <asm/arch/clock.h>
__weak void init_clk_usdhc(u32 index)
{
}
static int fsl_esdhc_of_to_plat(struct udevice *dev)
{
#if !CONFIG_IS_ENABLED(OF_PLATDATA)
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
#if CONFIG_IS_ENABLED(DM_REGULATOR)
struct udevice *vqmmc_dev;
int ret;
#endif
const void *fdt = gd->fdt_blob;
int node = dev_of_offset(dev);
fdt_addr_t addr;
unsigned int val;
addr = dev_read_addr(dev);
if (addr == FDT_ADDR_T_NONE)
return -EINVAL;
priv->esdhc_regs = (struct fsl_esdhc *)addr;
priv->dev = dev;
priv->mode = -1;
val = dev_read_u32_default(dev, "bus-width", -1);
if (val == 8)
priv->bus_width = 8;
else if (val == 4)
priv->bus_width = 4;
else
priv->bus_width = 1;
val = fdtdec_get_int(fdt, node, "fsl,tuning-step", 1);
priv->tuning_step = val;
val = fdtdec_get_int(fdt, node, "fsl,tuning-start-tap",
ESDHC_TUNING_START_TAP_DEFAULT);
priv->tuning_start_tap = val;
val = fdtdec_get_int(fdt, node, "fsl,strobe-dll-delay-target",
ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT);
priv->strobe_dll_delay_target = val;
val = fdtdec_get_int(fdt, node, "fsl,signal-voltage-switch-extra-delay-ms", 0);
priv->signal_voltage_switch_extra_delay_ms = val;
if (dev_read_bool(dev, "broken-cd"))
priv->broken_cd = 1;
if (dev_read_bool(dev, "non-removable")) {
priv->non_removable = 1;
} else {
priv->non_removable = 0;
#if CONFIG_IS_ENABLED(DM_GPIO)
gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
GPIOD_IS_IN);
#endif
}
if (dev_read_prop(dev, "fsl,wp-controller", NULL)) {
priv->wp_enable = 1;
} else {
priv->wp_enable = 0;
#if CONFIG_IS_ENABLED(DM_GPIO)
gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio,
GPIOD_IS_IN);
#endif
}
priv->vs18_enable = 0;
#if CONFIG_IS_ENABLED(DM_REGULATOR)
/*
* If emmc I/O has a fixed voltage at 1.8V, this must be provided,
* otherwise, emmc will work abnormally.
*/
ret = device_get_supply_regulator(dev, "vqmmc-supply", &vqmmc_dev);
if (ret) {
dev_dbg(dev, "no vqmmc-supply\n");
} else {
priv->vqmmc_dev = vqmmc_dev;
ret = regulator_set_enable(vqmmc_dev, true);
if (ret) {
dev_err(dev, "fail to enable vqmmc-supply\n");
return ret;
}
if (regulator_get_value(vqmmc_dev) == 1800000)
priv->vs18_enable = 1;
}
#endif
#endif
return 0;
}
static int fsl_esdhc_probe(struct udevice *dev)
{
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
struct fsl_esdhc_plat *plat = dev_get_plat(dev);
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
struct esdhc_soc_data *data =
(struct esdhc_soc_data *)dev_get_driver_data(dev);
struct mmc *mmc;
#if !CONFIG_IS_ENABLED(BLK)
struct blk_desc *bdesc;
#endif
int ret;
#if CONFIG_IS_ENABLED(OF_PLATDATA)
struct dtd_fsl_esdhc *dtplat = &plat->dtplat;
unsigned int val;
priv->esdhc_regs = map_sysmem(dtplat->reg[0], dtplat->reg[1]);
val = plat->dtplat.bus_width;
if (val == 8)
priv->bus_width = 8;
else if (val == 4)
priv->bus_width = 4;
else
priv->bus_width = 1;
if (dtplat->non_removable)
priv->non_removable = 1;
else
priv->non_removable = 0;
if (CONFIG_IS_ENABLED(DM_GPIO) && !priv->non_removable) {
struct udevice *gpiodev;
ret = device_get_by_ofplat_idx(dtplat->cd_gpios->idx, &gpiodev);
if (ret)
return ret;
ret = gpio_dev_request_index(gpiodev, gpiodev->name, "cd-gpios",
dtplat->cd_gpios->arg[0], GPIOD_IS_IN,
dtplat->cd_gpios->arg[1], &priv->cd_gpio);
if (ret)
return ret;
}
#endif
if (data)
priv->flags = data->flags;
/*
* TODO:
* Because lack of clk driver, if SDHC clk is not enabled,
* need to enable it first before this driver is invoked.
*
* we use MXC_ESDHC_CLK to get clk freq.
* If one would like to make this function work,
* the aliases should be provided in dts as this:
*
* aliases {
* mmc0 = &usdhc1;
* mmc1 = &usdhc2;
* mmc2 = &usdhc3;
* mmc3 = &usdhc4;
* };
* Then if your board only supports mmc2 and mmc3, but we can
* correctly get the seq as 2 and 3, then let mxc_get_clock
* work as expected.
*/
init_clk_usdhc(dev_seq(dev));
#if CONFIG_IS_ENABLED(CLK)
/* Assigned clock already set clock */
ret = clk_get_by_name(dev, "per", &priv->per_clk);
if (ret) {
printf("Failed to get per_clk\n");
return ret;
}
ret = clk_enable(&priv->per_clk);
if (ret) {
printf("Failed to enable per_clk\n");
return ret;
}
priv->sdhc_clk = clk_get_rate(&priv->per_clk);
#else
priv->sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK + dev_seq(dev));
if (priv->sdhc_clk <= 0) {
dev_err(dev, "Unable to get clk for %s\n", dev->name);
return -EINVAL;
}
#endif
ret = fsl_esdhc_init(priv, plat);
if (ret) {
dev_err(dev, "fsl_esdhc_init failure\n");
return ret;
}
#if !CONFIG_IS_ENABLED(OF_PLATDATA)
ret = mmc_of_parse(dev, &plat->cfg);
if (ret)
return ret;
#endif
mmc = &plat->mmc;
mmc->cfg = &plat->cfg;
mmc->dev = dev;
#if !CONFIG_IS_ENABLED(BLK)
mmc->priv = priv;
/* Setup dsr related values */
mmc->dsr_imp = 0;
mmc->dsr = ESDHC_DRIVER_STAGE_VALUE;
/* Setup the universal parts of the block interface just once */
bdesc = mmc_get_blk_desc(mmc);
bdesc->if_type = IF_TYPE_MMC;
bdesc->removable = 1;
bdesc->devnum = mmc_get_next_devnum();
bdesc->block_read = mmc_bread;
bdesc->block_write = mmc_bwrite;
bdesc->block_erase = mmc_berase;
/* setup initial part type */
bdesc->part_type = mmc->cfg->part_type;
mmc_list_add(mmc);
#endif
upriv->mmc = mmc;
return esdhc_init_common(priv, mmc);
}
#if CONFIG_IS_ENABLED(DM_MMC)
static int fsl_esdhc_get_cd(struct udevice *dev)
{
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
return esdhc_getcd_common(priv);
}
static int fsl_esdhc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
struct mmc_data *data)
{
struct fsl_esdhc_plat *plat = dev_get_plat(dev);
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
return esdhc_send_cmd_common(priv, &plat->mmc, cmd, data);
}
static int fsl_esdhc_set_ios(struct udevice *dev)
{
struct fsl_esdhc_plat *plat = dev_get_plat(dev);
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
return esdhc_set_ios_common(priv, &plat->mmc);
}
#if CONFIG_IS_ENABLED(MMC_HS400_ES_SUPPORT)
static int fsl_esdhc_set_enhanced_strobe(struct udevice *dev)
{
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
struct fsl_esdhc *regs = priv->esdhc_regs;
u32 m;
m = esdhc_read32(&regs->mixctrl);
m |= MIX_CTRL_HS400_ES;
esdhc_write32(&regs->mixctrl, m);
return 0;
}
#endif
static int fsl_esdhc_wait_dat0(struct udevice *dev, int state,
int timeout_us)
{
int ret;
u32 tmp;
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
struct fsl_esdhc *regs = priv->esdhc_regs;
ret = readx_poll_timeout(esdhc_read32, &regs->prsstat, tmp,
!!(tmp & PRSSTAT_DAT0) == !!state,
timeout_us);
return ret;
}
static const struct dm_mmc_ops fsl_esdhc_ops = {
.get_cd = fsl_esdhc_get_cd,
.send_cmd = fsl_esdhc_send_cmd,
.set_ios = fsl_esdhc_set_ios,
#ifdef MMC_SUPPORTS_TUNING
.execute_tuning = fsl_esdhc_execute_tuning,
#endif
#if CONFIG_IS_ENABLED(MMC_HS400_ES_SUPPORT)
.set_enhanced_strobe = fsl_esdhc_set_enhanced_strobe,
#endif
.wait_dat0 = fsl_esdhc_wait_dat0,
};
#endif
static struct esdhc_soc_data usdhc_imx7d_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
| ESDHC_FLAG_HS400,
};
static struct esdhc_soc_data usdhc_imx8qm_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING |
ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 |
ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES,
};
static const struct udevice_id fsl_esdhc_ids[] = {
{ .compatible = "fsl,imx51-esdhc", },
{ .compatible = "fsl,imx53-esdhc", },
{ .compatible = "fsl,imx6ul-usdhc", },
{ .compatible = "fsl,imx6sx-usdhc", },
{ .compatible = "fsl,imx6sl-usdhc", },
{ .compatible = "fsl,imx6q-usdhc", },
{ .compatible = "fsl,imx7d-usdhc", .data = (ulong)&usdhc_imx7d_data,},
{ .compatible = "fsl,imx7ulp-usdhc", },
{ .compatible = "fsl,imx8qm-usdhc", .data = (ulong)&usdhc_imx8qm_data,},
{ .compatible = "fsl,imx8mm-usdhc", .data = (ulong)&usdhc_imx8qm_data,},
{ .compatible = "fsl,imx8mn-usdhc", .data = (ulong)&usdhc_imx8qm_data,},
{ .compatible = "fsl,imx8mq-usdhc", .data = (ulong)&usdhc_imx8qm_data,},
{ .compatible = "fsl,imxrt-usdhc", },
{ .compatible = "fsl,esdhc", },
{ /* sentinel */ }
};
#if CONFIG_IS_ENABLED(BLK)
static int fsl_esdhc_bind(struct udevice *dev)
{
struct fsl_esdhc_plat *plat = dev_get_plat(dev);
return mmc_bind(dev, &plat->mmc, &plat->cfg);
}
#endif
U_BOOT_DRIVER(fsl_esdhc) = {
.name = "fsl_esdhc",
.id = UCLASS_MMC,
.of_match = fsl_esdhc_ids,
.of_to_plat = fsl_esdhc_of_to_plat,
.ops = &fsl_esdhc_ops,
#if CONFIG_IS_ENABLED(BLK)
.bind = fsl_esdhc_bind,
#endif
.probe = fsl_esdhc_probe,
.plat_auto = sizeof(struct fsl_esdhc_plat),
.priv_auto = sizeof(struct fsl_esdhc_priv),
};
DM_DRIVER_ALIAS(fsl_esdhc, fsl_imx6q_usdhc)
#endif
Reference in New Issue View Git Blame Copy Permalink