mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-07-06 11:16:15 +09:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
131 lines
2.9 KiB
C
131 lines
2.9 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2011
|
|
* eInfochips Ltd. <www.einfochips.com>
|
|
* Written-by: Ajay Bhargav <contact@8051projects.net>
|
|
*
|
|
* Based on Aspenite:
|
|
* (C) Copyright 2010
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
* Contributor: Mahavir Jain <mjain@marvell.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <mvmfp.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/mfp.h>
|
|
#include <asm/arch/armada100.h>
|
|
#include <asm/gpio.h>
|
|
#include <miiphy.h>
|
|
#include <asm/mach-types.h>
|
|
|
|
#ifdef CONFIG_ARMADA100_FEC
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#endif /* CONFIG_ARMADA100_FEC */
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
u32 mfp_cfg[] = {
|
|
/* I2C */
|
|
MFP105_CI2C_SDA,
|
|
MFP106_CI2C_SCL,
|
|
|
|
/* Enable Console on UART3 */
|
|
MFPO8_UART3_TXD,
|
|
MFPO9_UART3_RXD,
|
|
|
|
/* Ethernet PHY Interface */
|
|
MFP086_ETH_TXCLK,
|
|
MFP087_ETH_TXEN,
|
|
MFP088_ETH_TXDQ3,
|
|
MFP089_ETH_TXDQ2,
|
|
MFP090_ETH_TXDQ1,
|
|
MFP091_ETH_TXDQ0,
|
|
MFP092_ETH_CRS,
|
|
MFP093_ETH_COL,
|
|
MFP094_ETH_RXCLK,
|
|
MFP095_ETH_RXER,
|
|
MFP096_ETH_RXDQ3,
|
|
MFP097_ETH_RXDQ2,
|
|
MFP098_ETH_RXDQ1,
|
|
MFP099_ETH_RXDQ0,
|
|
MFP100_ETH_MDC,
|
|
MFP101_ETH_MDIO,
|
|
MFP103_ETH_RXDV,
|
|
|
|
/* SSP2 */
|
|
MFP107_SSP2_RXD,
|
|
MFP108_SSP2_TXD,
|
|
MFP110_SSP2_CS,
|
|
MFP111_SSP2_CLK,
|
|
|
|
MFP_EOC /*End of configuration*/
|
|
};
|
|
/* configure MFP's */
|
|
mfp_config(mfp_cfg);
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
struct armd1apb2_registers *apb2_regs =
|
|
(struct armd1apb2_registers *)ARMD1_APBC2_BASE;
|
|
|
|
/* arch number of Board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_GPLUGD;
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
|
|
/* Assert PHY_RST# */
|
|
gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_LOW);
|
|
udelay(10);
|
|
/* Deassert PHY_RST# */
|
|
gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH);
|
|
|
|
/* Enable SSP2 clock */
|
|
writel(SSP2_APBCLK | SSP2_FNCLK, &apb2_regs->ssp2_clkrst);
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_ARMADA100_FEC
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
struct armd1apmu_registers *apmu_regs =
|
|
(struct armd1apmu_registers *)ARMD1_APMU_BASE;
|
|
|
|
/* Enable clock of ethernet controller */
|
|
writel(FE_CLK_RST | FE_CLK_ENA, &apmu_regs->fecrc);
|
|
|
|
return armada100_fec_register(ARMD1_FEC_BASE);
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
/* Configure and initialize PHY chip 88E3015 */
|
|
void reset_phy(void)
|
|
{
|
|
u16 phy_adr;
|
|
const char *name = "armd-fec0";
|
|
|
|
if (miiphy_set_current_dev(name))
|
|
return;
|
|
|
|
/* command to read PHY dev address */
|
|
if (miiphy_read(name, 0xff, 0xff, &phy_adr)) {
|
|
printf("Err..%s could not read PHY dev address\n", __func__);
|
|
return;
|
|
}
|
|
|
|
/* Set Ethernet LED in TX blink mode */
|
|
miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00);
|
|
miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL);
|
|
|
|
/* reset the phy */
|
|
miiphy_reset(name, phy_adr);
|
|
debug("88E3015 Initialized on %s\n", name);
|
|
}
|
|
#endif /* CONFIG_RESET_PHY_R */
|
|
#endif /* CONFIG_ARMADA100_FEC */
|